Installation Guide

ManualsBrandsRaytec ManualsAccessoriesRAYMAX 100 Platinum, 10-20 Deg, 850nm

Installation Steps

1. Mount Illuminator

2. Mount Power Supply Unit (PSU)

3. Connect Illuminator to PSU

4. PSU connections

5. Connect PSU to Mains

Set Up Steps

1. Position illuminator adjacent to

camera and point towards scene

2. Adjust vertical angle

3. Adjust horizontal angle via Adaptive

Illumination (AI) (if required)

4. Tighten all ﬁxings

Package Contents

1. Illuminator

2. Power Supply (PSU)

illuminators installation guide

(including IR Covert, IR PLATINUM, HYBRID and Low Voltage Series)

LUXMAX

and

RAYMAX / RAYLUX illuminator

PSU

Overview

This installation guide provides instructions for installing the RAYMAX

and RAYLUX series illuminators

WARNING

Version 3.1

GOLDEN RULES:

1. Ensure PSU lid orientation has

warning label in line with glands

(see PSU diagram, right)

2. Ensure operating voltage is

correct for unit being installed

3. DO NOT INPUT MAINS VOLTAGE

INTO LOW VOLTAGE PSU

4. Ensure PSU is fully water tight

Summary of content (12 pages)

PAGE 1
MAX and LUX illuminators installation guide (including IR Covert, IR PLATINUM, HYBRID and Low Voltage Series) This installation guide provides instructions for installing the RAYMAX and RAYLUX series illuminators Installation Steps 1. 2. 3. 4. 5. Mount Illuminator Mount Power Supply Unit (PSU) Connect Illuminator to PSU PSU connections Connect PSU to Mains Overview Set Up Steps 1. Position illuminator adjacent to camera and point towards scene 2. Adjust vertical angle 3.
PAGE 2
Adaptive illumination bolt LED illuminator Bracket LED output cable x2 2.5m (8.2ft) Photocell (automatic operation) LED output 1 LED output 2 Mains input ! 1.5m Isolate mains before removing cover 2 Mount PSU to flat surface Install in a well ventilated area Do not continually stare at lamp Specifications subject to change without notice. Installation to be carried out by suitable trained and qualified personnel.
PAGE 3
Installation 1m (3.3ft - 29m 9.
PAGE 4
Set Up TARGET 1 Position illuminator adjacent to camera and point towards scene (Optional night set-up for optimum image performance) 2 Adjust vertical angle ! Max x2 3 Adjust horizontal angle via Adaptive 4 Tighten all fixings Illumination (AI) (if required) ! CAUTION: Do not fully loosen AI bolt.
PAGE 5
Technical Drawings (Not to scale) Standard Bracketry 100mm (4”) 25mm (1”) 12.5mm (0.5”) 47mm (1.9”) RM/RL 25 36mm (1.4”) 72mm (2.8”) 52mm (2”) RM/RL 200/100/50 33mm (1.
PAGE 6
PSU Specifications Infra-Red Series PSU RM300 RM200 RM150 RM100 RM50 RM25 Input AC 100-230 universal<120W AC 100-230 universal<80W AC 100-230 universal<60W AC 100-230 universal<40W AC 100-230 universal<20W AC 100-230 universal<10W Fuse 2.5A anti-surge 2.5A anti-surge 2.5A anti-surge 2.5A anti-surge 1A anti-surge 1A anti-surge Typical Output (Standard) 6.6A @ 13.5V 4.4A @ 13.5V 3.6A @ 13.5V 2.4A @ 13.5V 1A @ 13.5V 0.5A @ 13.
PAGE 7
Low Voltage PSU (LVP) Specification Infra-Red and WHITE-LIGHT Series PSU (Excluding Platinum and Covert Series) 300 200 150 100 50 25 Input x 24V AC/DC x 24V AC/DC 12/24V AC/DC 12/24V AC/DC Fuse x 5A x 5A 3A 3A Typical Output (Infra-Red) x 4.4A @ 13.5V x 2.4A @ 13.5V 1A @ 13.5V 0.5A @ 13.5V Typical Output (White-Light) x 4.2A @ 13.5V x 2.8A @ 13.5V 1.4A @ 13.5V 0.7A @ 13.5V Adjustable Power x 10% - 100% x 10% - 100% 10% - 100% 10% - 100% Weight x 1.85 kg (4.
PAGE 8
Power Supply Diagrams (Not to scale) Infra-Red and White-Light RM/RL 50/25 Models (Not to scale) Photocell Power Adjust LED Output x2 (Polarity Sensitive) Telemetry Input - requires zero volt, latched input Photocell Sensitivity Mains Input 100V to 230V AC Auto-Sensing Infra-Red and White-Light RM/RL 200/100 Models (Model shown: RM/RL 100 Premium) (Not to scale) 12V DC power output (Premium PSU only) Photocell following contact - volt free, non polarity sensitive (Premium PSU only) Telemetry Input
PAGE 9
Infra-Red and White-Light RM/RL 300/150 and Hybrid Models (Final specification model dependant - model shown: RM/RL 300 Premium) Note - Hybrid control boards will be labelled IR/WL Photocell following contact - volt free, non polarity sensitive (Premium PSU only) Telemetry Input requires zero volt, latched input Photocell Sensitivity Photocell 12V DC Power Output (Premium PSU only) Power Adjust Up to x3 LED Output (Polarity Sensitive) (Model Dependant) Mains Input (100V to 230V AC) Auto-Sensing 9
PAGE 10
Trouble Shooting Ensure all tests are undertaken by a qualified, trained engineer.
PAGE 11
Step 3: Set-up Camera, lens and illumination Check alignment of lamp Check camera lens – fully open at night & set correctly Check model number to Raytec performance specification to ensure required distance is achievable Step 4: Call Raytec for further assistance Note down: • Model and serial number of illuminator • Camera make and model • Lens make and model If the Raytec lamp is still not delivering the required performance, please contact us for further assistance.
PAGE 12
UK / Europe T: +44 (0) 1670 520055 F: +44 (0) 1670 819760 sales@rayteccctv.com Americas (Toll Free) T: +1 888 505 8335 ussales@rayteccctv.com www.rayteccctv.