81253_1.book Page 1 Monday, May 9, 2005 9:36 AM SeaTalk2 Keyboard Owner's Handbook www.raymarine.com Introduction PAGE WPTS MOB ACTIVE DATA MENU OUT . OK CANCEL IN This handbook explains how to install, connect, operate and maintain your SeaTalk2 Keyboard (E55061). This keyboard is also supplied with the Remote Station Kit (T82005) details of how to integrate these devices is given on Page 6.
81253_1.book Page 2 Monday, May 9, 2005 9:36 AM The controls WPTS MOB To manage waypoints and initiate MOB. Power To turn display off and access backlight functions and scanner controls. Soft keys Press to select corresponding function identified by on-screen label. PAGE To change page and configure page sets. Trackpad To control on-screen cursor and scroll through menu items.
81253_1.book Page 3 Monday, May 9, 2005 9:36 AM Whats in the box?. . . . Suncover Stud (x2) Clamp (x2) SeaTalk2 Keyboard Thumb nut (x2) Drain tube (8mm x 1m) SeaTalk2 cable (1.5m) SeaTalk2 power/RF ground cable (1.5m) Cradle Terminator (x2) SeaTalk2 Keyboard Owner's Handbook www.raymarine.com Introduction to the SeaTalk2 Keyboard Gasket PAGE WPTS ACTIVE MOB DATA MENU OUT .
81253_1.book Page 4 Monday, May 9, 2005 9:36 AM Planning the installation Where can the SeaTalk2 Keyboard be mounted? The Seatalk2 keyboard can be flush or trunnion mounted either indoors or outdoors. It is waterproof to CFR-46 standard. Important: The drain tube is not required if the keyboard is mounted indoors or in an area protected from rain and/or sea spray.
81253_1.book Page 5 Monday, May 9, 2005 9:36 AM Configuration 2 Cable length between E-Series Display and keyboard exceeds 4.5m and Not linking into an existing SeaTalk2 system. Supplied in the box E Series display Not supplied/accessory/ existing system Keyboard cable (attached/3m) SeaTalk2 Keyboard E-Series Display SeaTalk2 extension cable (see 'Accessories') SeaTalk2 cable (1.5m) SeaTalk2 Power/RF ground cable (1.
81253_1.book Page 6 Monday, May 9, 2005 9:36 AM Integrating the Remote Station Kit Station 1 M1500 monitor No other SeaTalk devices connected Alarm Alarm Black Drain Other SeaTalk devices Yellow VGA out cable, 5m NOT waterproof Black Brown Yellow Red Black Drain OR VGA out cable, waterproof (see Accessories) Black White White 12v supply Red SeaTalk2 Keyboard Red Red Brown Other SeaTalk devices connected OR Junction box Remote Station Kit SeaTalk2 cable (1.
81253_1.book Page 7 Monday, May 9, 2005 9:36 AM Installation Note: Before installing the keyboard, please read 'Planning the installation' on Pages 4 & 5. What tools do I need to install the keyboard? Drill 10 mm (3/8 in) drill bit File Jigsaw Masking or adhesive tape How do I install the keyboard? 1. Using self-adhesive or masking tape, fix the 3. Saw around the shaded area of the template. template in the required position.
1253_1.book Page 8 Monday, May 9, 2005 9:36 AM Installation - continued 5. Peel the backing from the gasket and stick it 8. Fit the keyboard assembly into its housing. to the underside of the cradle. With the dimples in the clamps fitting into the nipples on the cradle, fit and secure the clamps in place using the thumb nuts. 6. Finger tighten the studs into position. 9.
81253_1.book Page 9 Monday, May 9, 2005 9:36 AM Accessories and spares What accessories are available? ... Description Part no. SeaTalk2 E55070 power/RF ground cable (1.5m) Auxiliary alarm E26033 M1500 monitor kit (includes 5m VGA Out cable) E02009 Terminator E25048 Junction box E25049 SeaTalk2 extension cables: 1 metre E25040 3 metres E25042 5 metres E25043 10 metres E25038 20 metres E25044 E-Series SeaTalk2 cable (1.
81253_1.book Page 10 Monday, May 9, 2005 9:36 AM Removing/refitting How do I remove the keyboard? ... 3. Push down at the top of the keyboard to 1. Switch off the power. raise it from the cradle and lift the it from the cradle. 2. Slide and hold the latch. How do I refit the keyboard? ... 2. Push the bottom of the keyboard into the cradle to engage the latch. 1. Position the top edge of the keyboard under the lip of the cradle. Maintenance What routine checks and servicing can I do? ...
81253_1.book Page 11 Monday, May 9, 2005 9:36 AM Important information EMC conformance All Raymarine equipment and accessories are designed to the best industry standards for use in the recreational marine environment. The design and manufacture of Raymarine equipment and accessories conforms to the appropriate Electromagnetic Compatibility (EMC) standards, but correct installation is required to ensure that performance is not compromised.
81253_1.book Page 12 Monday, May 9, 2005 9:36 AM Technical support & contact information www.raymarine.com Visit the Customer Support area of our website for Frequently Asked Questions, servicing information, e-mail access to the Raymarine Technical Support Department and details of Raymarine agents, worldwide. United States Europe For accessories and parts contact: For technical support, service and accessories contact: Your authorized Raymarine dealer.
