81258_3.
81258_3.book Page 2 Wednesday, November 8, 2006 2:06 PM Trademarks and registered trademarks Autohelm, HSB, Raymarine, RayTech, Sail Pilot, SeaTalk and Sportpilot are registered trademarks of Raymarine Limited. Apelco is a registered trademark of Raymarine Holdings Limited (Registered in all major marketing territories).
81258_3.book Page 1 Wednesday, November 8, 2006 2:06 PM Contents 1 Contents Safety notices ............................................................................... 1 Important information................................................................ 3 Geographic location .......................................................................... 3 Television reception........................................................................... 4 EMC conformance .....................................
81258_3.book Page 2 Wednesday, November 8, 2006 2:06 PM 2 Maintenance and troubleshooting .......................................... 45 Introduction ........................................................................................ 45 Maintenance....................................................................................... 45 Troubleshooting.................................................................................. 45 Antenna diagnosis .................................................
81258_3.book Page 1 Wednesday, November 8, 2006 2:06 PM 1 Safety notices CAUTION WARNING Product installation Connectors This equipment must be installed in accordance with the instructions contained in this handbook. Failure to do so could result in poor product performance, personal injury and/or damage to your boat. Take care not to damage the exposed connectors below the base plate when moving the unit. DO NOT use these connectors to lift the unit.
81258_3.
81258_3.book Page 3 Wednesday, November 8, 2006 2:06 PM 3 Important information Introduction This handbook contains an explanation of how to install, connect and maintain your Raymarine Satellite TV system. This handbook covers the following models: • 45STV Satellite TV system. •60STV Satellite TV D7943_ 1 system. Your Raymarine Satellite TV system provides uninterrupted television access to hundreds of TV channels in all types of weather conditions.
1258_3.book Page 4 Wednesday, November 8, 2006 2:06 PM 4 Raymarine Satellite TV Systems Television reception For full functionality of your Raymarine Satellite TV system, it is necessary to subscribe to the relevant service(s) from the appropriate service provider(s). Full details of service providers can be found in “Satellite service providers” on page 62. EMC conformance All Raymarine equipment and accessories are designed to the best industry standards for use in the leisure marine market.
81258_3.book Page 5 Wednesday, November 8, 2006 2:06 PM 5 What does a typical system look like? Raymarine Satellite TV Antenna Power/Data cable DC Power RF cable Satellite Receiver (IRD) Antenna Control Unit Television D7944_1 Note: Satellite receivers, televisions and subscription services must be purchased separately.
81258_3.
81258_3.book Page 7 Wednesday, November 8, 2006 2:06 PM 7 Installation EMC installation guidelines All Raymarine equipment and accessories are designed to the best industry standards for use in the recreational marine environment. Their design and manufacture conforms to the appropriate Electromagnetic Compatibility (EMC) standards, but correct installation is required to ensure that performance is not compromised.
81258_3.book Page 8 Wednesday, November 8, 2006 2:06 PM 8 Raymarine Satellite TV Systems What’s in the box?.... Raymarine STV Antenna Unit houses the antenna positioning mechanism, low noise block (LNB), power supply and control elements within a molded radome. Connectors on the underside of the base plate join the power, signal and control cabling from the below decks units. D7945_1 Antenna Control Unit (ACU) controls power to the antenna unit via the On/Off switch.
81258_3.book Page 9 Wednesday, November 8, 2006 2:06 PM 9 What tools do I need to install my TV system?....
81258_3.book Page 10 Wednesday, November 8, 2006 2:06 PM 10 Raymarine Satellite TV Systems How do I plan the installation?... Make sure nearby objects do not block the antenna. It requires a +150 to +900 look angle to receive satellite signals .
81258_3.book Page 11 Wednesday, November 8, 2006 2:06 PM 11 Extending the cables The cables that have been supplied with your Raymarine Satellite TV system should be of adequate length to complete the installation on most boats. However, should it be necessary to extend a cable the following points should be considered: Power and data cable This cable is supplied at a length of 15 m. If a longer length is required you should replace this cable with Raymarine Part No.E96007 - 30 m Power/Data cable.
81258_3.book Page 12 Wednesday, November 8, 2006 2:06 PM 12 Raymarine Satellite TV Systems How do I install the ACU?.... ACU dimensions 195 mm (7.67 in) 229 mm (9.0 in) 160 mm (6.3 in) 224.6 mm (8.84 in) 62.7 mm (2.47 in) 65 mm (2.56 in) 195 mm (7.
81258_3.book Page 13 Wednesday, November 8, 2006 2:06 PM 13 Installing the ACU The ACU should be installed below decks, in a position that is: • dry. • well ventilated. • easily accessible. • near your main TV viewing area. The ACU should be installed using the two fixing brackets supplied. These brackets can be placed on the sides of the unit to provide a top or bottom fix. _1 953 D7 To install the ACU: 1.
81258_3.book Page 14 Wednesday, November 8, 2006 2:06 PM 14 Raymarine Satellite TV Systems Securing the antenna How do I install the antenna?.... Preparing the antenna 1. Using a 5 mm allen key, remove the antenna dome retaining bolts and dome. 2. Remove the foam transit restraints from the antenna base. 3. Replace and secure the antenna dome. Secure the antenna to the base using bolts, spring washers and flat washers.
81258_3.book Page 15 Wednesday, November 8, 2006 2:06 PM 15 How do I connect the system cables?.... Antenna baseplate To connect the antenna 1. Pass the power/data cable through the access hole of the mounting plate and connect it to the power/data connector on the antenna base plate. There are two types of antenna baseplate that can be fitted to your Raymarine TV System.
81258_3.book Page 16 Wednesday, November 8, 2006 2:06 PM 16 Raymarine Satellite TV Systems How do I configure the system?... Connecting the ACU Your Raymarine Satellite TV system can be connected with multiple IRDs at the same time to receive pictures in different cabins offering the maximum choice of channels. The following section shows the different combinations available and their connections. In all cases the ACU must be connected to the power/data connector of the antenna base plate.
81258_3.book Page 17 Wednesday, November 8, 2006 2:06 PM 17 Twin IRDs You can connect two IRDs to your antenna as shown in the following diagram.However, only one of the IRDs can be configured as a two satellite receiver. The other IRD needs to be configured as a one satellite receiver. The two satellite receiver determines which satellite is tracked, while the other receiver can watch any channel which is available from the tracked satellite.
81258_3.book Page 18 Wednesday, November 8, 2006 2:06 PM 18 Multiple IRDs Raymarine Satellite TV Systems 6. Connect the multi-switch to the appropriate DC power supply. IMPORTANT: Due to satellite polarization, incorrect connection in systems using multiple IRDs will result in signal degradation. Make sure you select the correct method of connection for your area of operation.
81258_3.book Page 19 Wednesday, November 8, 2006 2:06 PM 19 North American systems - DirecTV This version of a multi-switch installation uses a DiSEqC supplier - Raymarine Part No. A96014 - and enables you to change the satellite being tracked as you change channels using the IRD master instead of the ACU. 1 RF1 POWER PC I NTERFACE FUSE ANTENNA RF2 DC10.8 - 15.
81258_3.book Page 20 Wednesday, November 8, 2006 2:06 PM 20 • Set the ACU to ON. • The IRDs to OFF. • The television receivers to OFF. 6. Confirm that the antenna detects and tracks the DirecTV101 satellite. 7. Set the Master IRD to ON. 8. Set the Master IRD television receiver to ON. 9. Set the remaining IRDs to ON. 10. Set the remaining television receivers to ON. The system can now be controlled using the Master IRD. Raymarine Satellite TV Systems 5.
81258_3.book Page 21 Wednesday, November 8, 2006 2:06 PM 21 System with 4 RF connector baseplate Single IRD This is the basic method for connecting your Raymarine Satellite TV System.
81258_3.book Page 22 Wednesday, November 8, 2006 2:06 PM 22 Raymarine Satellite TV Systems Multiple IRDs Systems using more than 4 IRDs In European systems fitted with a 4 RF connector baseplate there are two options for connecting multiple IRDs. To connect more than 4 IRDs you will need to install a suitable active multiswitch between the antenna and the IRDs. Systems using up to 4 IRDs In European systems all four RF outputs from the antenna can be connected to individual IRDs.
81258_3.book Page 23 Wednesday, November 8, 2006 2:06 PM 23 Connecting your satellite TV system to an NMEA0183 GPS Note: This applies to Raymarine 60 STV systems only. Rear view 4. Strip back the wires from one end of the additional piece of cable and place the yellow (NMEA OUT) and ground wires into the connector block. 5. Tighten the connector block screws. 6. Strip back the wires on the free end of the additional piece of cable and place them in the connector block of the 9 pin connector.
81258_3.
81258_3.book Page 25 Wednesday, November 8, 2006 2:06 PM 25 System set up Introduction Set up using the ACU This section of the handbook describes how to set up your Raymarine Satellite TV system after installation using the ACU or the Graphical User Interface (GUI) and includes the following functions: Start up D7964_1 INITIALIZE ACU RAYMARINE 45STV INITIALIZE ANTENNA RAYMARINE 45STV 1. Communication is being established between the antenna and the ACU D7965_1 2. The antenna is initialized.
81258_3.book Page 26 Wednesday, November 8, 2006 2:06 PM 26 Raymarine Satellite TV Systems Changing the default satellite TRACKING A: SETUP A: ASTRA 2 HOTBIRD SETUP SETUP 4. Antenna is again tracking satellite A. Press to display position detail. 5. Antenna position detail and signal strength is displayed. Press center soft key to display NMEA GPS page. D7968_1 B: HOTBIRD TRACKING B: D7970_1 ASTRA2 ASTRA2 D7971_1 TRACKING A: B: HOTBIRD Your ACU is programmed with two default satellites.
81258_3.book Page 27 Wednesday, November 8, 2006 2:06 PM 27 Set up mode Setting the satellite pair To enter set up mode: This sequence applies to all satellite pairs except DirecTV: SETUP MODE? NEXT SAT A : ASTRA 2 NEXT SELECT EXIT D7975_1 NO YES D7973_1 YES 2. Press YES to enter setup mode. SET SAT PAIR? PREV D7974_1 SETUP D7972_1 B : HOTBIRD 1. With the antenna tracking press SETUP. YES NEXT 3. Press YES to set the satellite pair.
81258_3.book Page 28 Wednesday, November 8, 2006 2:06 PM 28 Raymarine Satellite TV Systems Setting the satellite pair - DirecTV SAT A* : DTV119 SAT A : DTV101 SELECT EXIT D78642_1 NEXT SAT B: DTV101 SELECT EXIT D8643_1 NEXT 1. Follow steps 1 thru 3 for entering set up mode- see “Set up mode” on page 27. Press YES to set satellite pair. 2. Set satellite A. Press NEXT to show alternative satellite name. Press SELECT to set chosen satellite to SAT A. Press EXIT to return to main set up menu. 3.
81258_3.book Page 29 Wednesday, November 8, 2006 2:06 PM 29 Setting the GPS using the ACU LATITUDE 1. Press YES to enter set up mode. NO D7973_1 YES D7982_1 + SETUP MODE? ##.##N INPUT - SAVE? YES NEXT D7974_1 PREV 3. Press YES to set GPS. NEXT D7980_1 YES + 28.20E _ INPUT D7981_1 LONGITUDE NO 6. Press YES to accept the data. Press NO to cancel and return to main set up menu. Note: If your system is connected to a GPS antenna, the position will be updated in real time.
81258_3.book Page 30 Wednesday, November 8, 2006 2:06 PM 30 Raymarine Satellite TV Systems Edit satellite information SATNAME : ASTRA 2 - 1. Press YES to enter set up mode. NO D7973_1 YES INPUT D7985_1 + SETUP MODE? LONGITUDE YES NEXT D7974_1 PREV 2. Press NEXT twice to enter Edit Sat Info menu. + VER LOW YES NEXT + 10788 22000 INPUT - 7. Input the tracking frequency (MHz) and symbol rate (kHz) for Vertical Low Band. D7983_1 PREV 3. Press YES to enter edit menu. 6.
81258_3.book Page 31 Wednesday, November 8, 2006 2:06 PM 31 HOR LOW INPUT 0X0020 D7989_1 + NID VER HIGH INPUT D7990_1 + 11895 27500 VER HIGH NID 0X0020 INPUT HOR HIGH 10. Input the NID for Horizontal Low Band. VERIFY : DVB DECODE 11. Input the tracking frequency (MHz) and symbol rate (kHz) for Vertical High Band. POWER : AUTO HOR HIGH 11954 27500 p INPUT D7992_1 + + PREV PREV 12. Input the NID for Vertical High Band.
81258_3.book Page 32 Wednesday, November 8, 2006 2:06 PM 32 Raymarine Satellite TV Systems Setting the local frequency AUTO - change voltage to LNB by IRD voltage. ONLY 13 V - always supply 13 V to LNB. ONLY 18 V - always supply 18 V to LNB. Note: (1) Raymarine does not recommend changing the satellite information unless advised to do so by the satellite provider. LNB systems in regions with circular polarization SETUP MODE? YES 1. Press YES to enter set up mode.
81258_3.book Page 33 Wednesday, November 8, 2006 2:06 PM 33 INPUT D7998_1 + 5. Input local frequency for the LNB. + increases a value. - decreases a value. Change the underscored digit using the +/- buttons. Press INPUT to accept a value SET SAT PAIR? PREV YES NEXT D8646_1 LOCAL FREQ : ####MHZ SET LOCAL FRQ? SAVE? NO D7977_1 YES YES 3. Press YES to set local frequency. NEXT D7996_1 PREV 6. Press YES to accept the data. Press NO to cancel and return to main set up menu.
81258_3.book Page 34 Wednesday, November 8, 2006 2:06 PM 34 Raymarine Satellite TV Systems Setting the DiSEqC method SAVE? SETUP MODE? 1. Press YES to enter set up mode. NO 5. Press YES to accept the selection. Press NO to cancel and return to main set up menu. D7973_1 YES NO D7977_1 YES * DiSEqC method SET SAT PAIR? YES NEXT D7974_1 PREV USE DISEQC? YES 3. Press YES to enter the DiSEqC menu. NEXT D8000_1 PREV 2. Press NEXT 4 times to go to the Use DiSEqC menu.
81258_3.book Page 35 Wednesday, November 8, 2006 2:06 PM 35 Setting the LNB skew angle Note: This menu is only applicable to Raymarine 60STV Premium models SKEW : CALIBRATION SELECT NEXT Dxxxx_1 PREV SETUP MODE? 1. Press YES to enter set up mode. NO D7973_1 YES 4. Select skew angle adjustment method*. PREV - view previous setting NEXT - view next setting SELECT - select the current setting SKEW : ##.# SET Dxxxx_1 - -> ### SET SAT PAIR? YES NEXT D8646_1 PREV 5.
81258_3.book Page 36 Wednesday, November 8, 2006 2:06 PM 36 Raymarine Satellite TV Systems Display version SETUP MODE? EXIT ACU S/W VER : 1.00 D8002_1 EXIT 2. Press NEXT 5 times to go to View Version menu. SET SAT PAIR? YES NEXT D8646_1 PREV YES 1. Press YES to enter set up mode. NO D7973_1 NEXT D8003_1 YES 3. Press YES to view product name and software versions. SET SAT PAIR? D9610_1 EXIT 4. Product name is displayed. Press EXIT to return to main set up menu.
81258_3.book Page 37 Wednesday, November 8, 2006 2:06 PM 37 NEXT YES NO D8008_1 YES GO TO POSITION? D8002_1 PREV 3. Press YES to enter Go position. - + ###.##DEG INPUT D8007_1 EL : 4. Input position value for azimuth (AZ) axis. + increases a value. - decreases a value. Change the underscored digit using the +/- buttons. Press INPUT to accept a value. 5. Input position value for elevation (EL) axis. + increases a value. - decreases a value. Change the underscored digit using the +/- buttons.
81258_3.book Page 38 Wednesday, November 8, 2006 2:06 PM 38 Raymarine Satellite TV Systems 3. Press YES to enter the Ant move step menu. ANT MOVE STEP? YES NEXT SETUP MODE? D8010_1 PREV Setting defaults 1. Press YES to enter set up mode. NO D7973_1 YES STEP AZ : ###.# EL CCW SET SAT PAIR? PREV YES NEXT D8646_1 D8011 1 CW 4. Move the antenna in the AZ axis. CW - move clockwise. EL - go to the elevation control screen. CCW - move counter-clockwise. EXIT DOWN 5.
81258_3.book Page 39 Wednesday, November 8, 2006 2:06 PM 39 Set up using the Graphical User Interface You can also set up your Raymarine Satellite TV system using the Graphical User Interface (GUI) which can be found on the CD-ROM. The CD-ROM contains folders for the different areas of operation. Open the correct folder for your area of operation. The method of operation is the same for all versions of the GUI. 4.
81258_3.book Page 40 Wednesday, November 8, 2006 2:06 PM 40 Raymarine Satellite TV Systems Antenna status The antenna status information shows monitoring and set up information for your antenna. Target satellite selection and monitoring This section enables you to set up satellite tracking and monitoring. Satellite pair This section shows satellites being tracked. Local frequency and signal strength This section shows the local satellite frequency and signal strength.
81258_3.book Page 41 Wednesday, November 8, 2006 2:06 PM 41 Restart Click this soft key to restart the antenna tracking the chosen satellite. Setup Click this soft key to enter the GUI set up mode prior to making any changes. Get Antenna Information Click this soft key to display the current system settings. Setting the GPS Your system antenna uses GPS information to enable it to track the satellite faster. The better the GPS information, the better the antenna performance.
81258_3.book Page 42 Wednesday, November 8, 2006 2:06 PM 42 Raymarine Satellite TV Systems 4. Click the drop-down arrow at the right of the longitude box and select W or E according to your longitude. 5. Click on the latitude box and enter your latitude in degrees and minutes format. 6. Click the drop-down arrow at the right of the latitude box and select N or S according to your latitude. 7. Click ‘Set GPS’ to save this information and set the GPS. 8. Click ‘Restart’.
81258_3.book Page 43 Wednesday, November 8, 2006 2:06 PM 43 Setting antenna angle, move step and diagnosis. You can move the antenna to a new target position or carry out diagnosis using the Move antenna - Execute diagnosis function of the GUI. D8020_1 Moving the antenna to a new position There are two methods for moving (stepping) the antenna to a new position: • • Positioning based on an absolute angle. Positioning based on a relative angle. To position using an absolute angle: 1.
81258_3.book Page 44 Wednesday, November 8, 2006 2:06 PM 44 Raymarine Satellite TV Systems • Red - shows that there is a fault with that function. If a fault is diagnosed refer to “Troubleshooting” on page 45 for possible solutions. 4. Click ‘Restart’. The system leaves set up mode and the antenna will start tracking. LNB Setting the skew angle Antenna flange D8022_1 Note: This section is only applicable to regions with linear polarization.
81258_3.book Page 45 Wednesday, November 8, 2006 2:06 PM 45 Maintenance and troubleshooting Introduction Troubleshooting This section deals with maintenance and troubleshooting that can be carried out by the system user. Your Raymarine product has been subjected to comprehensive test and quality assurance programs prior to packing and shipping.
81258_3.book Page 46 Wednesday, November 8, 2006 2:06 PM 46 1. Blown fuse, low power or wiring • Check that the in-line quick blow fuse (if fitted) has not blown, or the circuit breaker has not tripped. Replace fuse with one of the same type and rating. • If you have extended the power cable from the antenna unit, check that there is no power loss. • Check the system wiring and connections. 2.
81258_3.book Page 47 Wednesday, November 8, 2006 2:06 PM 47 Antenna diagnosis 1. Press YES to enter set up mode. CODE101 PASSED SETUP MODE? EXIT D8649 1 NO D7973_1 YES 2. Press NEXT 8 times to go to Antenna Diagnosis menu. SET SAT PAIR? YES NEXT D7974_1 PREV 5. Code 101 has been tested and passed. Press Exit to return to main set up menu. Code Test Code 101 Communication between antenna and ACU is being tested. If failed, check the power and data cable connections. 3.
81258_3.book Page 48 Wednesday, November 8, 2006 2:06 PM 48 Raymarine Satellite TV Systems Technical support You can obtain Technical Support for your Raymarine Satellite TV System from the following: www.raymarine.
81258_3.book Page 49 Wednesday, November 8, 2006 2:06 PM 49 Satellite information Introduction European satellites This section contains information on satellites in your region and includes: Astra 1G/1H • • • Satellite coverage areas. Satellite coverage by geographic location. Satellite tracking information Satellite coverage areas 60STV The following satellite coverage maps do not guarantee coverage. This can be affected by climatic conditions that may cause variation in the satellite signal.
81258_3.
81258_3.
81258_3.
81258_3.
81258_3.
81258_3.
81258_3.
81258_3.
81258_3.
81258_3.
81258_3.book Page 60 Wednesday, November 8, 2006 2:06 PM 60 Raymarine Satellite TV Systems Satellite coverage by geographic location The following table details satellite coverage by geographic location. To receive a satellite television service you will need to subscribe to the service from the relevant service provider. Country Satellites Service provider Spain Primary: Astra - AST01GKU Hispasat www.hispasat.
81258_3.book Page 61 Wednesday, November 8, 2006 2:06 PM 61 Hotbird www.eutelsat.com EchoStar 3 - ECH003KB EchoStar 6.8 - ECH008KB EchoStar 7 - ECH007KB EchoStar 1.2 - ECH001KB EchoStar Communications Corp. www.dishnetwork.com Turksat www.satcom.gov.tr DIRECTV 2.3 - DTV123KB DIRECTV 6 - DTV006KB DirectV Inc. www.directv.com Country Satellites Service provider Turkey Hotbird - HOT234KW Turksat - TUR01BKT Turksat - TUR01CEB Russia Thor - THO003KU Hotbird - HOT234KW Thor www.telenor.
81258_3.book Page 62 Wednesday, November 8, 2006 2:06 PM 62 Raymarine Satellite TV Systems Satellite tracking Satellite service providers Your Raymarine Satellite TV System can track a variety of DVB compatible and DSS (DIRECTV) satellites. Your system contains a pre-programmed library of either European or North American satellites, whichever are applicable to your system. There are also two open slots which can be programmed with user defined satellites.
81258_3.
81258_3.
81258_3.
81258_3.
81258_3.book Page 67 Wednesday, November 8, 2006 2:06 PM 67 Appendix 7: Technical specification Raymarine 45 STV General Approvals CE - conforms to FCC- verified to Dimensions Satellite antenna unit Antenna dish diameter Antenna control unit Weight Satellite antenna unit Antenna control unit Environmental Operating temperature range Storage temperature range Humidity limit Antenna system performance EU Directive 89/336/EEC CFR47: Part 15 500 mm x 538 mm (19.7 x 21.2 ins.) 450 mm (18 ins.
81258_3.book Page 68 Wednesday, November 8, 2006 2:06 PM 68 Raymarine Satellite TV Systems Universal Twin LNBF Universal Twin LNBF Local oscillator frequency 9.75 GHz - Low band 10.6 GHz - High band Local oscillator frequency stability + 1.0 MHz @ 25oC + 2.0 MHz @ -40oC ~ 60oC Local oscillator phase noise -50 dBc/Hz @ 1 KHz maximum -75 dBc/Hz @ 10 KHz maximum -95 dBc/Hz @ 100 KHz maximum Gain flatness + 0.
81258_3.book Page 69 Wednesday, November 8, 2006 2:06 PM 69 Dual LNBF Gain variation 5 dB (max) across 500 MHz Cross polarization isolation 25 dB (min.) Image rejection 40 dBm (min.) Output VWSR 2.1(max) in a 75 W system Noise figure 1.1 dB (max) Po 1 dB 0 dBm (min.) 3rd order intermodulation -50 dBc (max), two tones of -15 dBm output spaced 27 MHz Polarization switching voltage 10.5 V ~ 14.0 V @ RHCP 15.0 V ~ 21.
81258_3.book Page 70 Wednesday, November 8, 2006 2:06 PM 70 Raymarine Satellite TV Systems Raymarine 60 STV General Approvals CE - conforms to FCC- verified to Dimensions Satellite antenna unit Antenna dish diameter Antenna control unit Weight Satellite antenna unit Antenna control unit Environmental Operating temperature range Storage temperature range Humidity limit Operating voltage Power consumption Antenna system performance Frequency Ku-band (10.7 to 12.
81258_3.book Page 71 Wednesday, November 8, 2006 2:06 PM 71 Universal Twin LNBF Local oscillator frequency stability Local oscillator phase noise Universal Twin LNBF + 1.0 MHz @ 25o C + 2.0 MHz @ -40oC ~ 60oC -50 dBc/Hz @ 1 kHz -75 dBc/Hz @ 10 kHz -95 dBc/Hz @ 100 kHz Conversion gain 50 dB (min), 60 dB (max) Gain flatness + 0.
81258_3.book Page 72 Wednesday, November 8, 2006 2:06 PM 72 Raymarine Satellite TV Systems Dual LNBF (US models) QuadLNBF (EU Premium models) Image rejection 40 dBm (min.) Output VWSR 2.1(max) in a 75 W system Noise figure 1.1 dB (max) Po 1 dB 0 dBm (min.) 3 rd order intermodulation -50 dBc (max), two tones of -15 dBm output spaced 27 MHz Polarization switching voltage 10.5 V ~ 14.0 V @ RHCP 15.0 V ~ 21.
81258_3.book Page 73 Wednesday, November 8, 2006 2:06 PM 73 QuadLNBF (EU Premium models) Polarization switching voltage 10.5 V ~ 14.0 V @ VP 16.0 V ~ 19.0 V @ HP DC current consumption 160 mA (max) Band switching signal (DiSEqC 1.
81258_3.
