New a Series New c Series New e Series Installation and operation instructions English Date: 02-2013 Document number: 81337-6-EN © 2013 Raymarine UK Limited
Trademark and patents notice Autohelm, hsb2, RayTech Navigator, Sail Pilot, SeaTalk, SeaTalkNG, SeaTalkHS and Sportpilot are registered trademarks of Raymarine UK Limited. RayTalk, Seahawk, Smartpilot, Pathfinder and Raymarine are registered trademarks of Raymarine Holdings Limited. FLIR is a registered trademark of FLIR Systems, Inc. and/or its subsidiaries.
Contents Chapter 1 Important information.......................... 9 4.7 AIS connection..................................................... 50 TFT Displays ............................................................... 9 Water ingress ............................................................ 10 4.8 Fastheading connection........................................ 51 Disclaimers ............................................................... 10 Chart cards and memory cards..............................
Chapter 9 Autopilot control .............................. 101 Chapter 16 Radar application........................... 159 9.1 Autopilot control ................................................. 102 9.2 Autopilot status symbols ..................................... 103 16.1 Radar overview ................................................ 160 16.2 Radar scan speed ............................................ 161 9.3 Autopilot alarms ................................................. 104 16.
19.2 Thermal camera image..................................... 216 Chapter 26 Customizing your display ............. 267 19.3 Controls overview............................................. 217 19.4 Camera control ................................................ 218 26.1 Language selection .......................................... 268 26.2 Boat details...................................................... 269 19.5 Image adjustments ........................................... 220 26.3 Units set-up .....
New a Series / New c Series / New e Series
Chapter 1: Important information Warning: Product installation and operation This product must be installed and operated in accordance with the instructions provided. Failure to do so could result in personal injury, damage to your vessel and/or poor product performance. Warning: Potential ignition source This product is NOT approved for use in hazardous/flammable atmospheres. Do NOT install in a hazardous/flammable atmosphere (such as in an engine room or near fuel tanks).
Water ingress Water ingress disclaimer Although the waterproof rating capacity of this product meets the IPX6 standard, water intrusion and subsequent equipment failure may occur if the product is subjected to commercial high-pressure washing. Raymarine will not warrant products subjected to high-pressure washing. Disclaimers This product (including the electronic charts) is intended to be used only as an aid to navigation. It is designed to facilitate use of official government charts, not replace them.
Industry Canada Product disposal This device complies with Industry Canada License-exempt RSS standard(s). Dispose of this product in accordance with the WEEE Directive. Operation is subject to the following two conditions: 1. This device may not cause interference; and 2. This device must accept any interference, including interference that may cause undesired operation of the device.
New a Series / New c Series / New e Series
Chapter 2: Handbook information Chapter contents • 2.1 Handbook information on page 14 • 2.2 Product information on page 15 • 2.3 Handbook illustrations on page 16 • 2.4 Handbook conventions on page 17 • 2.
2.1 Handbook information This handbook contains important information regarding your multifunction display. The handbook is for use with the following Raymarine multifunction displays: Additional handbooks Description Part number SeaTalkng reference manual 81300 • New a Series User manuals Print Shop • New c Series Raymarine provides a Print Shop service, enabling you to purchase a high-quality, professionally-printed manual for your Raymarine product.
2.2 Product information The following Raymarine multifunction display variants are available Nonsonar Sonar Series a65 (E70076) a67 (E70077) New a Series Controls Features • Bluetooth. Touchscreen only a65 Wi-Fi (E70162) a67 Wi-Fi (E70163) • Internal GPS. • Bluetooth. New a Series Touchscreen only • Internal GPS. • WiFi e7 (E62354) e7D (E62355) • Bluetooth. New e Series HybridTouch (Touchscreen and physical buttons) • Wi-Fi • NMEA 0183 • NMEA 2000 (via SeaTalkng) • Internal GPS.
2.3 Handbook illustrations The illustrations and screenshots used in this handbook may differ slightly from your display model. The illustration of the multifunction display below is used throughout this manual and unless otherwise stated can apply to all variants of multifunction display (i.e. New a series, New c Series and New e Series).
2.4 Handbook conventions The following conventions are used throughout this handbook when referring to: Type Icons Example Convention The term "select" is used in procedures involving icons to refer to the action of selecting an on-screen icon, either using touch or physical buttons: • Touch — Press your finger on the icon to select. • Physical buttons — Use the Joystick to highlight the icon and press the Ok button.
Waypoint (MOB) button / icon Depending on the multifunction display variant there will be either a Waypoint (MOB) button or an on-screen icon. WPT button • New c Series • New e Series WPT icons • New a Series Throughout this manual the term: Select WPT, refers to pressing the physical WPT button or pressing the on-screen WPT icon.
2.5 Touch and non-touch operations This handbook applies to New a Series, New c Series and New e Series multifunction displays. All features and functions can be accessed using physical buttons (non-touch) on New c Series and New e Series displays or by using the touchscreen on New a Series and New e Series displays. This handbook uses icons throughout to identify whether a particular task is a touch or a non-touch operation.
New a Series / New c Series / New e Series
Chapter 3: Planning the installation Chapter contents • 3.1 System integration on page 22 • 3.2 Installation checklist on page 26 • 3.3 System Limits on page 26 • 3.4 Multiple data sources (MDS) overview on page 27 • 3.5 Identifying your display variant on page 27 • 3.6 Networking constraints on page 28 • 3.7 Typical systems on page 29 • 3.8 System protocols on page 32 • 3.9 Data master on page 33 • 3.10 New a Series parts supplied on page 33 • 3.
3.1 System integration Your multifunction display is compatible with a wide range of marine electronics devices. 1 2 3 5 4 7 6 8 SMARTPILOT RAY240 9 17 10 11 18 12 13 19 15 14 20 21 16 22 23 D12244-2 The display uses a number of protocols to transfer data between the various devices in your system.
Item Device Type Maximum quantity Suitable Devices Connections 4 GPS (external) — Raymarine 1 Any combination of the following: SeaTalk, SeaTalkng, or NMEA 0183. • Raystar125 GPS. • Raystar125+ GPS (via optional SeaTalk to SeaTalkng converter). • RS130 5 Instruments — Raymarine As determined by SeaTalkng bus bandwidth and power loading. SeaTalk (via optional SeaTalk to SeaTalkng converter): SeaTalk, SeaTalkng. • ST40 Wind, Speed, Depth, Rudder, or Compass.
Item Device Type Maximum quantity Suitable Devices Connections 10 Video / camera • New a Series = 0 Composite PAL or NTSC video source. BNC connectors. Third party IP camera Via SeaTalkhs network. • e7, e7D, New c Series =1 • New e Series (excluding e7 and e7D) = 2 10 IP camera Only 1 camera may be viewed at a time. Note: IP cameras must be able to assign IP address via DHCP and allow unauthenticated, anonymous ONVIF access.
Item Device Type Maximum quantity Suitable Devices Connections 18 Additional multifunction display(s) — Raymarine 5 SeaTalkhs (recommended): SeaTalkhs. • New a Series multifunction displays. • New c Series multifunction displays. • New e Series multifunction displays. Note: You can connect Raymarine multifunction displays using NMEA 0183 or SeaTalkng but not all functions are supported. Note: Visit www.raymarine.com to download the latest software version for your display.
3.2 Installation checklist 3.3 System Limits Installation includes the following activities: The following limits apply to the number of system components that can be connected in a Raymarine multifunction display system. Installation Task 1 Plan your system. Component Maximum 2 Obtain all required equipment and tools. Site all equipment. Maximum number of SeaTalkhs devices 25 3 4 Route all cables. Maximum number of SeaTalkng devices 50 5 Drill cable and mounting holes.
3.4 Multiple data sources (MDS) overview Installations that include multiple instances of data sources can cause data conflicts. An example is an installation featuring more than one source of GPS data. MDS enables you to manage conflicts involving the following types of data: • GPS Position. • Heading. • Depth. 3.5 Identifying your display variant To discover which model display you have follow the steps below: From the homescreen: 1. Select Set-up. 2. Select Maintenance. 3. Select Diagnostics. 4.
3.6 Networking constraints New a Series, New c Series and New e Series displays can be networked together and can also be networked to Raymarine’s E-Series Widescreen displays and G-Series systems. Caution is advised when networking a New a Series, New c Series or New e Series to a network containing a E-Series Widescreen display or when connecting to a G-Series system as there are networking constraints and restrictions which apply.
3.7 Typical systems The illustrations below show examples of possible system configurations, for more details on compatible devices please refer to the System integration section. Note: In the examples below the multifunction display(s) could be any of the following: • New a Series • New c Series • New e Series Example: Basic system 2 1 3 4 5 SMARTPILOT SeaTalkhs / RayNet SeaTalkhs / RayNet SeaTalkng D12245-2 1. Raymarine Multifunction display. 2. Raymarine network switch. 3. Raymarine radar scanner.
Example: Basic system with sonar variant display 1 2 3 4 5 SMARTPILOT SeaTalkhs / RayNet SeaTalkng D12589-1 1. Multifunction display 2. Sonar transducer. 3. Radar scanner. 4. SPX course computer. 5. SeaTalkng pilot controller. Example: Basic system with non-sonar variant display 2 1 3 4 5 SMARTPILOT SeaTalkhs / RayNet SeaTalkng D12590-1 1. Multifunction display. 2. Sonar module. 3. Sonar transducer. 4. SPX course computer. 5. SeaTalkng pilot controller.
Example: Expanded system 5 SeaTalkhs / RayNet 12 6 7 4 8 9 SeaTalkng 3 SeaTalkng 2 SeaTalkng 1 SeaTalkng 10 15 SeaTalkhs / RayNet 12 DeviceNet 14 12 13 11 SeaTalkhs / RayNet SeaTalkhs / RayNet SeaTalkhs / RayNet D12247-2 1. Radar scanner. 2. Weather sensor. 3. Sirius weather receiver. 4. Sonar module. 5. SeaTalkng Pilot controller. 6. SeaTalkng Instrument display. 7. AIS receiver / transceiver. 8. Audio system. 9. Smartphone / tablet. 10. DeviceNet spur (for NMEA 2000 devices). 11.
3.8 System protocols Your Multifunction Display can connect to various instruments and displays to share information and so improve the functionality of the system. These connections may be made using a number of different protocols. Fast and accurate data collection and transfer is achieved by using a combination of the following data protocols: is generally used to connect a data receiver and a transmitter together, e.g. a compass sensor transmitting heading to a radar display.
3.9 Data master 3.10 New a Series parts supplied Any system containing more than one networked multifunction display must have a designated data master. The following items are supplied with your multifunction display. The data master is the display which serves as a primary source of data for all displays, it also handles all external sources of information.
3.11 e7 / e7D Parts supplied 3.12 New c Series and New e Series parts supplied The parts shown below are supplied with the e7 / e7D multifunction display. The parts shown below are supplied with the New c Series and New e Series (Excluding e7 and e7D) multifunction displays. 5 4 3 4 2 1 x4 x4 3 6 2 x4 9 5 6 1 7 7 8 D12170-3 D12248-2 1. Sun cover. 2. Front bezel. 3. Multifunction display. 4. Rear bezel (required for trunnion bracket mounting). 5. Gasket (required for flush mounting). 6.
3.13 Tools required for installation 1 2 3 6 4 7 5 8 D12171-2 1. Power drill. 2. Jigsaw. 3. Pozidrive screwdriver. 4. Adhesive tape. 5. Spanner for surface mounting or bracket mounting fixings. 6. File. 7. Hole saw for flush mounting (For hole saw size refer to your product’s mounting template). 8. Drill bit for surface mounting or bracket mounting.
New a Series / New c Series / New e Series
Chapter 4: Cables and connections Chapter contents • 4.1 General cabling guidance on page 38 • 4.2 Connections overview on page 39 • 4.3 Power connection — New a Series on page 40 • 4.4 Power connection — New c Series and New e Series on page 41 • 4.5 Network connections on page 43 • 4.6 GPS connection on page 50 • 4.7 AIS connection on page 50 • 4.8 Fastheading connection on page 51 • 4.9 SeaTalkng connections on page 51 • 4.10 SeaTalk connection on page 53 • 4.
4.1 General cabling guidance Cable types and length It is important to use cables of the appropriate type and length • Unless otherwise stated use only standard cables of the correct type, supplied by Raymarine. • Ensure that any non-Raymarine cables are of the correct quality and gauge. For example, longer power cable runs may require larger wire gauges to minimize voltage drop along the run. Routing cables Cables must be routed correctly, to maximize performance and prolong cable life.
4.2 Connections overview 0 0 Details of the connections available on Raymarine multifunction displays are shown below.
0 4.3 Power connection — New a Series 0 0 0 0 0 0 0 0 4 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 The following restrictions apply to any extension to the power cable: 0 0 • Cable must be of a suitable gauge for the circuit load. 0 • Each unit should have its own dedicated power cable wired back to the distribution panel. 2 3 5 Cable extension 6 D12581-1 1. Multifunction display rear panel connections. Total length (max) Supply voltage Cable gauge (AWG) 0–5 m (0–16.
4.4 Power connection — New c Series and New e Series Power cable The display is supplied with a combined power and data multi cable, this can be extended if required. Power cables available 5 4 1 2 Cable Part number 1.5 m (4.9 ft) Straight power and data cable R62379 1.5 m (4.9 ft) Right angled power and data cable R70029 Notes 3 Cable extension 7 6 The following restrictions apply to any extension to the power cable: • Cable must be of a suitable gauge for the circuit load.
Sharing a breaker Where more than 1 piece of equipment shares a breaker you must provide protection for the individual circuits. E.g. by connecting an in-line fuse for each power circuit. - + 1 2 3 4 4 D11637-2 1 Positive (+) bar 2 Negative (-) bar 3 Circuit breaker 4 Fuse Where possible, connect individual items of equipment to individual circuit breakers. Where this is not possible, use individual in-line fuses to provide the necessary protection.
4.5 Network connections You can connect a number of digital devices to your multifunction display using the Network connector(s) at the rear of the unit. A typical network of digital devices may include: • Up to 6 Raymarine multifunction displays. • SeaTalkhs or RayNet digital devices such as a sonar module and radar scanner. • Ethernet IP cameras. Note: Your multifunction display includes the following network connectors: • e7, e7D, a65 and a67 = 1 x SeaTalkhs / RayNet connector.
Network cable connector types There are 2 types of network cable connector — RayNet. SeaTalkhs patch cables SeaTalkhs and SeaTalkhs connector — used for connecting SeaTalkhs devices to a Raymarine network switch via SeaTalkhs cables. RayNet connector — used for connecting Raymarine network switches and SeaTalkhs devices to the multifunction display via RayNet cables. Also required for connecting a crossover coupler if only one device is being connected to the display's Network connector.
Radar connected using crossover coupler 1. Radar scanner 2. Multifunction display rear connector panel. 3. SeaTalkhs crossover coupler. 4. RayNet to SeaTalkhs network cable. 5. Connection to power supply — Open array scanners require a VCM (Voltage Converter Module). 1 Note: The connector on the free end of the radar cable does NOT have a locking mechanism. 2 4 3 5 D12253-1 Radar cable extension For longer cable runs a radar power and data digital cable extension is required.
Digital radar cables Sonar module connection You will need a dedicated radar power and data digital cable and SeaTalkhs network cables to connect your scanner to your system. Connection Required cable Radar scanner to power supply and Raymarine network switch. Power and data digital cable. For longer cable runs, extensions are available in a variety of lengths. Raymarine network switch to multifunction display. SeaTalkhs network cables, available in a variety of cable lengths.
600 watt sonar-compatible sonar transducer connection via optional adaptor — Sonar variant multifunction displays 1 2 3 D12257-1 1. Rear connector panel of multifunction display (Sonar variant). Sonar variant multifunction displays The table below details which multifunction display variants feature a built-in sonar module and can be connected directly to compatible sonar transducers. Sonar variants Non-sonar variants a67 a65 e7D e7 c97 c95 c127 c125 e97 e95 e127 e125 2.
used in conjunction with the multifunctional display to control the thermal camera if required. • “Dual payload” thermal cameras include 2 independent lenses; 1 for thermal (infrared) and 1 for visible light. If you only have 1 display you should only connect the video cable labelled “VIS / IR” (visible light / infrared) to the display. If you have 2 or more displays you should connect 1 cable to each display.
Fusion link connection Network connection You can connect a Fusion 700 series marine entertainment system to your multifunction display. 1 2 Direct connection 3 3 4 4 5 2 1 D12741-1 6 1. Multifunction display. 2. Fusion system. 3. RayNet to SeaTalkhs cable. 4. Fusion ethernet connector. Direct connection with networked multifunction displays 1 3 2 6 D12740-1 4 1. Network switch. 2. Fusion system. 3. RayNet to SeaTalkhs cable. 4. Fusion ethernet connector. 5.
4.6 GPS connection 4.7 AIS connection Depending on display variant, your multifunction display may include an internal GPS receiver. If required the multifunction display can also be connected to an external GPS receiver, using SeaTalkng or NMEA 0183. A compatible AIS can be connected using SeaTalkng or NMEA 0183. Connection using SeaTalkng GPS connection — SeaTalkng 2 1 1 2 SeaTalkng D12263-1 SeaTalkng D12261-1 1. Multifunction display. 1. Multifunction display. 2.
S M A R T P I L O 4.8 Fastheading connection 4.9 SeaTalkng connections If you wish to use MARPA (radar target acquisition) functions on your multifunction display you need either: The display can connect to a SeaTalkng system. • An autopilot connected to the multifunction display via SeaTalkng or NMEA 0183. The compass is connected to the course computer and calibrated via the pilot control head; or: • A Raymarine or third-party fastheading sensor connected to the multifunction display via NMEA 0183.
SeaTalkng cabling components Description Part No SeaTalkng SeaTalkng 3 m (9.8 ft) backbone A06035 SeaTalkng 5 m (16.4 ft) backbone A06036 SeaTalkng 9 m (29.5 ft) backbone A06068 SeaTalkng 20 m (65.6 ft) backbone A06037 cabling components and their purposes. Connection / Cable Notes Backbone cable (various lengths) The main cable carrying data. Spurs from the backbone are used to connect SeaTalkng devices.
4.10 SeaTalk connection You can connect SeaTalk devices to your multifunction display using the optional SeaTalk to SeaTalkng converter. 3 1 4.11 New a Series DSC VHF radio connection The New a Series multifunction display requires an NMEA 0183 to SeaTalkng converter and a powered SeaTalkng backbone to enable connection to a DSC VHF radio. 1 SeaTalk SeaTalkng NMEA0183 2 3 SeaTalkng 5 4 2 SeaTalkng D12265-1 D12743-1 1. SeaTalk device. 2. SeaTalk to SeaTalkng converter.
4.12 NMEA 0183 connection NMEA 0183 devices can be connected to New c Series and New e Series multifunction displays using the power and data cable. Note: New a Series does not support connection of NMEA 0183 devices.
4.13 NMEA 2000 connection 4.14 Camera / Video connection The display can receive data from NMEA 2000 devices (e.g. data from compatible engines). The NMEA 2000 connection is made using SeaTalkng and appropriate adaptor cables. A camera or a video device can be connected directly to New c Series and New e Series multifunction displays using the video connector on the power and data cable.
4.15 Camera / video in-out connection A camera / video device or external display can be connected to New e Series multifunction displays (excluding the e7 / e7D) using the dedicated video in/out connector. Note: New a Series and New c Series multifunction displays do not have a dedicated video in/out connector. Video In Examples of video input sources that you can connect to the display include: • Video camera.
4.16 Media player connection You can use your multifunction display to wirelessly control a Bluetooth-compatible media player (such as a smartphone). The media player must be compatible with the Bluetooth AVRCP protocol (version 2.1 or higher). 1 2 3 select Ok on the multifunction display. If the code does NOT match, repeat steps 4 to 8. 11. If the pairing was successful the multifunction display will confirm the pairing. The external media device is now paired with the multifunction display.
1. 2. 3. 4. 5. 6. Select Set-up. Select System Settings. Select Wireless Connections. Select Connection Manager. Select the media player device in the list. Select Unpair / Forget this device. 4.17 Bluetooth remote control connection You can control the multifunction display wirelessly using a Raymarine remote control unit. The remote control uses a Bluetooth wireless connection. 1 2 3 D12163-2 1. Multifunction display. 2. Bluetooth connection. 3.
9. When prompted, press the arrow button on your remote that you wish to be configured as the UP button. The other arrow button will automatically be configured as the DOWN button. If the pairing was successful a “Pairing Success” message will be displayed. If a “Pairing Failure” or “Pairing Timeout” message is displayed, repeat steps 1 to 8. Customizing the SHORTCUT button On your multifunction display, with the homescreen displayed: 1. Select Set-up. 2. Select System Settings. 3. Select External Devices.
4.18 Remote control functions Bu tto n s Arrow buttons Shortcut button Ra n g e or P a ir S e le c t D12051-2 Button Default functions: Range / zoom. Application where function available: Chart Radar Fishfinder Weather Homescreen • Press UP or DOWN arrow for momentary response. • Hold UP or DOWN arrow for continuous response. Open homescreen. Shortcut: Hold Select application in homescreen (in left-to-right, top-to-bottom order). • Press UP or DOWN arrow for momentary response.
Reconnecting the RCU 1. When you pair the RCU-3 with a multifunction display a wireless connection is established. 2. When you power off the multifunction display it loses its connection with the RCU-3 after 10 minutes. 60 5 55 10 50 15 45 40 Minutes 20 35 25 30 = > 10 Minutes 3. To restore the connection between the 2 units, press and hold any button on the RCU-3 for at least 3 seconds.
4.19 WiFi connections Raymarine mobile app connection You can use compatible tablet and smartphone devices as a wireless repeat display or remote control for your multifunction display. Raymarine apps allow you to stream and / or control, remotely what you see on your multifunction display to a compatible device, using a Wi-Fi connection. To use this feature you must first: • Ensure your device is compatible with the app you wish to use.
Chapter 5: Location and mounting Chapter contents • 5.1 Selecting a location on page 64 • 5.2 Mounting - New a Series on page 65 • 5.
5.1 Selecting a location 1 Warning: Potential ignition source 2 6 This product is NOT approved for use in hazardous/flammable atmospheres. Do NOT install in a hazardous/flammable atmosphere (such as in an engine room or near fuel tanks). 250 (9.8 mm 4 in ) 200 (7.8 mm 7 in ) mm 500.7 in) 9 1 ( 300 (11 mm .8 i n) 350 (13 mm .8 i n) General location requirements mm 700.5 in) 7 2 ( When selecting a location for your display it is important to consider a number of factors.
Viewing angle 00000 00000 A B 000 C Prevailing conditions 00000 The weather and location of the vessel can affect the GPS performance. Typically calm clear conditions provide for a more accurate GPS fix. Vessels at extreme northerly or southerly latitudes may also receive a weaker GPS signal. GPS antenna mounted below decks will be more susceptible to performance issues related to the prevailing conditions. 000 The construction of your vessel can have an impact on GPS performance.
0 D12585-2 1. Check the selected location for the unit. A clear, flat area with suitable clearance behind the panel is required. 2. Drill or knock out the 4 mounting holes on the unit 0 00 0 0 D12578-2 0 D12588-1 3. Fix the appropriate cutting template supplied with the product, to the selected location, using masking or self-adhesive tape. 4. Using a suitable hole saw (the size is indicated on the template), make a hole in each corner of the cut-out area. 5.
5.3 Mounting - New c Series and New e series Viewing angle 000 000000 000 display, ensuring that the clips along the bottom edge of the bezel latch into position. 000000 B C 000 A 000000 000 000000 D 000 000 D12268-1 e7 / e7D e95 / e97 / c95 / c97 e125 / e127 / c125 / c127 e165 A 70º 80º 80º 80º B 70º 80º 80º 80º C 70º 80º 80º 70º D 50º 60º 60º 70º D12586-1 4. Ensure the bezel is correctly aligned with the display, as shown. 5.
1. Remove the front bezel. Refer to the separate instructions provided for that procedure. 3 3. Using a suitable hole saw (the size is indicated on the template), make a hole in each corner of the cut-out area. 4. Using a suitable saw, cut along the inside edge of the cut-out line. 5. Ensure that the unit fits into the removed area and then file around the rough edge until smooth. 6. Drill 4 holes as indicated on the template to accept the fixings. 7.
• Attach the front bezel. display, ensuring that the clips along the bottom edge of the bezel latch into position. D12274-1 D12273-2 1. Mark the location of the mounting bracket screw holes on the chosen mounting surface. 2. Drill holes for the fixings using a suitable drill, ensuring there is nothing behind the surface that may be damaged. 3. Use the fixings supplied with the mounting bracket to attach securely. 4. Attach the display unit to the mounting bracket. Front bezel 4.
New a Series / New c Series / New e Series
Chapter 6: Getting started Chapter contents • 6.1 Display power on page 72 • 6.2 New a Series Controls on page 72 • 6.3 e7 / e7D Controls on page 73 • 6.4 c95 / c97 / c125 / c127 / e95 / e97 / e125 / e127 / e165 Controls on page 73 • 6.5 Hybridtouch overview on page 75 • 6.6 Touchscreen overview on page 75 • 6.7 Homescreen overview — New a Series on page 76 • 6.8 Homescreen overview — New c Series / New e Series on page 76 • 6.9 System checks on page 77 • 6.
6.1 Display power 6.2 New a Series Controls Powering the display on 1. Press the POWER button. 2. Select Accept to acknowledge the disclaimer message. 1 Powering the display on 1. Press the POWER button. 2. Press the OK button to accept the disclaimer message. 2 Powering the display off 3 D12577-1 1. Touchscreen — touch the screen to operate functions, including all menu operations. 1. Press and hold the POWER button until the countdown reaches zero.
6.3 e7 / e7D Controls 6.4 c95 / c97 / c125 / c127 / e95 / e97 / e125 / e127 / e165 Controls 1 2 1 2 3 3 4 4 5 5 6 6 7 7 D12179-1 8 1. Touchscreen — you can touch the screen to operate many common functions, including all menu operations (HybridTouch multifunction displays only). 11 10 2. Menu — accesses menus. Press again to close menus. 3. UniControl — provides a joystick and rotary control and an OK button for using menus and applications. 4.
List of cursor labels 1 2 3 Label Feature Application A/B Ruler line Chart AIS AIS target Chart COG Course Over Ground vector Chart CTR Center of radar Radar FLT Floating EBL/VRM Radar GRD Guard zone Radar HDG Heading vector Chart MARPA MARPA target Radar MOB Man Over Board marker Chart, Radar POS Vessel's position Chart RTE Route leg Chart SHM Ship's Heading Marker Radar TIDE Tide indicator Chart TRACK Track line Chart VRM/EBL VRM and EBL, 1 or 2 Radar WI
6.5 Hybridtouch overview 6.6 Touchscreen overview If your multifunction display features Hybridtouch, this enables you to operate the unit using the touchscreen and the physical keys. The touchscreen provides an alternative to using physical buttons to control your multifunction display. All functions can be accessed using the touchscreen. However, there may be situations (such as rough sea conditions) when it is not appropriate to use the touchscreen.
6.7 Homescreen overview — New a Series 6.8 Homescreen overview — New c Series / New e Series The homescreen provides a central point of access to your display's range of applications. The homescreen provides a central point of access to your display's range of applications. • The homescreen also provides quick access to your data (waypoints, routes, and tracks). • The homescreen also provides quick access to your data (waypoints, routes, and tracks).
6.9 System checks GPS Check GPS selection You can use an internal (if available) or external GPS receiver. 2 • Your multifunction display may feature an internal GPS receiver. 3 • You can also connect an external GPS receiver using SeaTalkng or NMEA 0183. 4 • Where appropriate use the System Settings menu to enable or disable the internal GPS receiver.
3. Select Radar so that Transmit is highlighted. The radar scanner should now be transmitting and receiving. 4. Check that the radar screen is operating correctly. Typical HD radar screen Adjusting the bearing alignment Once you have checked the bearing alignment you can proceed and make any required adjustments. With the radar application displayed: 1. Select Menu. 2. Select Scanner Set-up . 3. Select Advanced. 4. Select Bearing Alignment. Selecting Bearing Alignment displays the numeric adjust control.
4. Select Transducer. A list of transducers is displayed. 5. Select the transducer you want to use. Checking the sonar Sonar checks are made using the fishfinder application. 1. Select the fishfinder page. Panning and tilting, and the thermal image On a New e Series multifunction display you can pan and tilt the thermal camera image using the touchscreen. Move your finger up and down the screen to tilt the camera up or down.
6.10 Enabling autopilot functions 6.11 Enabling AIS functions With the homescreen displayed: 1. Select Set-up. 2. Select System Settings. 3. Select Autopilot Control so that On is highlighted. Selecting Autopilot Control switches the control On and Off. 4. Select Back to return to the System Settings menu. 5. Select Pilot Controls. If this menu option is disabled, no autopilot has been found. Check the physical connections, then repeat steps 1 to 5 above. 6.
6.12 Pages Pages are used to display applications. Pages are displayed and accessed on the homescreen. Each page can display more than 1 application. • You can set up and display up to 4 applications per page using a New c Series or New e Series (except for the e7 and e7D) multifunction display. • The New a Series and the e7 / e7D multifunction displays can only set up and show up to 2 applications per page.
6.13 Applications Chart application — provides a 2D or 3D graphical view of your charts to help you navigate. Waypoint, route, and track functions enable you to navigate to a specific location, build and navigate routes, or record where you've been. Chart cards provide higher levels of detail and 3D views. 6.14 Splitscreen controls When viewing a page with more than 1 application displayed you can switch applications from the splitscreen view to fullscreen view.
Selecting the active window — e7 / e7D 6.15 Screen overview When viewing a splitscreen page you can select the active application and view it fullscreen on an e7 / e7D with the touch lock enabled by following the steps below. With a page featuring multiple applications displayed: 1. Press the Menu button. 2. Select Cycle application. Selecting cycle application cycles through the available applications. 3. Select Fullscreen to view the active application in fullscreen, or 4.
1 2 Screen item Description 1 Back • Touchscreen — Select the on-screen Back icon to go back to the previous menu. 3 • Non–touchscreen — Use the Back button to go back to the previous menu. 2 Menu item • Touchscreen — Momentarily touching a menu item highlights and automatically selects the item.
Screen item Description Screen item Description 3 Close — On Touchscreen displays you can select this icon to close the menu(s). The close icon is not available on non-touchscreen displays. 1 4 Scroll bar Status — provides status information for the connected equipment. For example, the Pilot Control dialog displays the locked heading and current navigation mode for a connected autopilot unit. 2 Control icons — provide direct control of the connected equipment.
6.16 Editing information in dialogs 6.17 Editing numerical settings With the dialog displayed: 1. Select the field you want to edit. The on-screen keyboard is displayed: To edit numerical values in you can either use the Rotary Control, the on-screen numeric adjust control or on-screen numeric keypad to increase or decrease the value. 1 2 3 4 D12567-1 2. Use the on-screen keyboard to make the changes. 3. Use the on-screen keyboard's SAVE key to keep any changes.
6.18 Basic touchscreen operations Placing and moving the cursor using touch To place or move the cursor around the screen on a touchscreen multifunction display follow the steps below. 1. Touch the screen at any position on the screen to place the cursor there. 6.19 Databar status symbols The status symbols on the databar confirm whether the appropriate connections to your system have been made. The symbols show the status for the following: • Radar scanner. • AIS receiver / transceiver. • Sonar module.
Symbol Description Symbol Description AIS unit is connected and switched on, but has active alarms. Power steering active. AIS unit is connected and switched on, but the dangerous and lost alarm is disabled. Wind Vane mode is active. Sonar status symbols The sonar status is indicated in the databar. Symbol Description Symbol animated: the sonar module is connected and transmitting. Symbol static: the sonar module is connected but not transmitting.
6.20 Initial set up procedures Adjusting the display brightness — New a Series and New e Series Once your display has been installed and commissioned, Raymarine recommends that you perform an initial set up procedure. Startup wizard 1 2 3 4 5 D12568-1 When you power-up the display for the first time or after a system reset a Startup Wizard is displayed. The wizard guides you through the following initial settings: 1. Language selection 2. Vessel type selection 3. Configure units 4.
Data master Enabling and disabling simulator mode Any system containing more than one networked multifunction display must have a designated data master. The data master is the display which serves as a primary source of data for all displays, it also handles all external sources of information. For example the displays may require heading information from the autopilot and GPS systems, usually received through a SeaTalkng or NMEA connection.
Chapter 7: Managing display data Chapter contents • 7.1 Memory cards overview on page 92 • 7.2 Inserting a memory card or chart card on page 92 • 7.3 Removing a memory card or chart card on page 93 • 7.4 Saving user data and user settings on page 93 • 7.5 Screenshots on page 96 • 7.
7.1 Memory cards overview You can use memory cards to archive data such as waypoints, routes, and tracks. Memory cards can be used to archive your data when the system capacity is reached. You can then delete old data from your system, creating capacity for new data. The archived data can be retrieved at any time. You can also use memory cards to backup your data. Note: Raymarine recommends that you backup your data to a memory card on a regular basis. 7.
7.3 Removing a memory card or chart card From the homescreen: 1. Select My Data. 2. Select Eject Card. A message is displayed prompting you to select the memory device you want to eject. 3. Select SD1 for a memory card in the top card slot, or SD2 for a memory card in the bottom card slot. 4. Open the chart card door, located on the front right of the display. 5. Push the edge of the card towards the unit, until an audible click is heard.
want to erase data from, if your display only has 1 card slot then you will not be prompted. 4. Select SD1 for a memory card in the top card slot, or SD2 for a memory card in the bottom card slot. 5. Select Erase Waypoints from Card, Erase Routes from Card, or Erase Tracks from Card, as appropriate.
Chart application — Cartography settings Data application Application Setting Application Setting Cartography Data overlay cell 1 on / off Data Datapages and content Data overlay cell 1 content Datapage order Data overlay cell 2 on / off Color theme Data overlay cell 2 content Dial color Chart object menu Number of engines Chart display Maximum tachometer range Chart grid 2D shading Community layer Fishfinder application Application Setting Fishfinder Configure preset frequencies Ch
7.5 Screenshots 7.6 Resetting your system You can take a screenshot of what is currently displayed on the screen. Screenshots are saved to an SD card in .bmp (bitmap) format. The saved image can be viewed from the multifunction display or any device capable of viewing bitmap images. Your system may be reset to its factory default settings if required. There are 2 types of reset operation, both of which affect the current display you are using, AND any networked displays. • Settings reset.
Chapter 8: Document viewer application Chapter contents • 8.
8.1 Document viewer overview • Fit to Width — Scales the open document to fit the width of the application window. Your multifunction display includes a pdf document viewer. The document viewer is available from the homescreen and is used to view and search pdf documents (such as product handbooks). • Close File — Closes the open document. Opening the user manual The product user manual is stored on the internal memory. From the homescreen: 1. Select Doc Viewer. 2. Select User Manual.
Browsing an open document On HybridTouch and non-touch displays you can browse pdf documents by following the steps below. With a pdf document open: 1. Move the Joystick Up or Down to move up and down through the document. 2. Move the Joystick Left or Right to pan left and right. Changing the zoom factor On touchscreen displays you can change the zoom factor of the open document by following the steps below. With a pdf document open: 1. Select the on-screen Zoom in icon to zoom in, or 2.
New a Series / New c Series / New e Series
Chapter 9: Autopilot control Chapter contents • 9.1 Autopilot control on page 102 • 9.2 Autopilot status symbols on page 103 • 9.
9.1 Autopilot control You can use your multifunction display to control your autopilot. Note: For information on connecting your multifunction display to a Raymarine autopilot system, refer to the documentation that accompanied your autopilot. With the Autopilot Control function enabled, you can use your multifunction display to: • Engage the autopilot and instruct it to follow a route, or a waypoint. • Disengage the autopilot. 1. Select Set-up. 2. Select System Settings. 3.
1. Select Menu > Navigate > Goto Cursor, Goto Waypoint, or Follow Route as appropriate. The Pilot Control dialog is displayed. 2. Select Engage Pilot. A confirmation pop-up message is displayed. 3. Select Yes to confirm and engage the autopilot, or 4. Select No to leave the autopilot in the current state. Engaging the autopilot using the context menu From the chart application context menu. 1. Select any of the following options from the Chart context menu: • Goto Waypoint 9.
9.3 Autopilot alarms The autopilot function provides alarms to alert you to situations that require action. Your multifunction display shows autopilot alarms, regardless of whether there is active navigation on the system. If autopilot control is enabled, and an alarm is raised by the autopilot, the multifunction display provides an audible alarm sound (providing that the alarm has not already been silenced). The Pilot Control dialog is displayed, indicating a new alarm.
Chapter 10: Alarms and Man over board functions Chapter contents • 10.1 Using Man Overboard (MOB) functions on page 106 • 10.
10.1 Using Man Overboard (MOB) functions 1. Select Ok on the MOB alarm dialog. The alarm will be silenced but remains active. Man overboard Cancelling the man overboard (MOB) alarm — New a Series If you lose a person or object overboard, you can use the Man Overboard (MOB) function to mark the position that the vessel was at when the MOB function was activated. The MOB function is available at all times, regardless of which application is running. MOB can be set to Dead Reckoning or Position mode.
10.2 Alarms Alarms alert you to a situation or hazard requiring your attention. You can set up alarms to alert you to certain conditions, such as collision warnings and temperature limits. Alarms are raised by system functions, and also external equipment connected to your multifunction display. When an alarm sounds a message dialog is displayed on your multifunction display and any networked displays. The dialog states the reason for the alarm.
Alarms menu Menu item Description Options MOB Data Type Determines whether Position or Dead Reckoning (DR) data is displayed. Assuming that your vessel and the MOB are subject to the same tide and wind effects, the Dead Reckoning setting normally gives a more accurate course. • Dead Reckoning When set to On, an alarm is triggered at the time you specify for the Alarm Clock Time setting. Alarm Clock Alarm Clock • Position (default) • Off (default) • On Alarm Clock Time • 00:00 (default) • 00.
Menu item Description Options • Deep Fish Limit — Specifies the upper value for the Fish Alarm Depth Limit. • 2 ft (or equivalent units) to the maximum of the transducer range Deep Fish Limit • 2 ft (or equivalent units) to the maximum of the transducer range Fuel Manager In the fuel manager alarm options you can switch the low fuel warning alarm on or off and specify the fuel level at which the alarm is triggered.
New a Series / New c Series / New e Series
Chapter 11: DSC VHF radio integration Chapter contents • 11.1 Using a DSC VHF radio with your display on page 112 • 11.
11.1 Using a DSC VHF radio with your display 11.2 Enabling DSC VHF radio integration You can connect your DSC VHF radio to your multifunction display and show distress message information and GPS position data for other vessels. With the homescreen displayed: 1. Select Set-up. 2. Select System Settings. 3. Select DSC Alerts > ON.
Chapter 12: Fuel manager Chapter contents • 12.
12.1 Fuel manager overview Note: The fuel manager provides an estimate of fuel remaining, and the distance and time which can be travelled before the tanks are empty. In order to calculate these values, you must configure the total capacity of fuel available to the engines and log each time you add fuel. The fuel manager also allows you to set a low fuel warning alarm which is sounded when the vessel's estimated fuel falls below a specified value.
Setting the low fuel alarm Note: Using the fuel manager also allows you to set a low fuel alarm which, if activated, is sounded when your vessel’s remaining fuel falls to a specified value. The fuel range ring is an estimated range that can be reached at the current rate of fuel consumption, of the fuel onboard and based on a number of external factors which could either extend or shorten the projected range. With the fuel manager turned on and set up correctly: 1. From the homescreen select Set-Up. 2.
New a Series / New c Series / New e Series
Chapter 13: AIS function Chapter contents • 13.1 AIS overview on page 118 • 13.2 AIS prerequisites on page 119 • 13.3 AIS context menu on page 119 • 13.4 Enabling AIS on page 120 • 13.5 Displaying AIS vectors on page 120 • 13.6 AIS status symbols on page 121 • 13.7 AIS silent mode on page 121 • 13.8 AIS target symbols on page 122 • 13.9 Displaying detailed AIS target information on page 122 • 13.10 Viewing all AIS targets on page 123 • 13.
13.1 AIS overview AIS Simulator Mode The AIS feature enables you to receive information broadcast by other vessels, and to add these vessels as targets in the chart and radar applications. With an optional AIS unit connected to your system you can: • Display targets for any other AIS-equipped vessels. • Display voyage information being broadcast by these targets, such as their position, course, speed and rate-of-turn.
13.2 AIS prerequisites 13.3 AIS context menu You must have suitable AIS hardware connected to your multifunction display to make use of the AIS functionality. The AIS function includes a context menu which provides AIS target information and menu items. In order to run AIS, you will need: • A receive-only AIS unit or a full AIS transceiver (a unit that sends and receives). • A VHF antenna. • A GPS - to provide position data. • The AIS layer enabled in the chart or radar application, as appropriate.
13.4 Enabling AIS 13.5 Displaying AIS vectors Enabling AIS in the chart application You must have the correct data available before AIS vectors can be displayed. To enable AIS overlay in the chart application the chart view must be set to 2D Menu > Presentation > Chart View. A target is defined as active when it has the following data displayed graphically: From the chart application: 1. Select Menu. 2. Select Presentation. 3. Select Layers. 4. Select AIS: so that On is highlighted.
13.6 AIS status symbols 13.7 AIS silent mode AIS status is indicated by a symbol in the databar. AIS silent mode enables you to disable AIS transmissions Symbol Description AIS unit is switched on and operating. AIS currently unavailable. AIS unit is switched off, or not connected. AIS unit is in Silent Mode. AIS unit is in Silent Mode, with active alarms. AIS unit is connected and switched on, but has active alarms.
13.8 AIS target symbols Your multifunction display shows a range of symbols to represent the different types of AIS target. Target type Description Transmitting target Target is moving or at anchor (Target is not activated, dangerous or lost). Activated target Target activated — that is, AIS vector displayed. Vector line (optional) shows predicted distance travelled within a given time. Selected target Target selected with cursor. Can view detailed data. Symbol 13.
13.10 Viewing all AIS targets 13.11 Using AIS to avoid collisions From the chart application go to Menu > AIS Options You can use the AIS safe zone and safety message functions to help you avoid collisions with other vessels and objects. From the radar application go to Menu > Track Targets > View AIS Lists 1. Select AIS List. A list of all available AIS targets is displayed.
Enabling and disabling AIS safety messages in the radar application From in the radar application: 1. Select Menu. 2. Select Track Targets. 3. Select AIS Unit Set-up. 4. Select AIS Safety Messages. Selecting AIS Safety Messages will switch between safety messages On and Off. 13.12 AIS options The AIS options are accessible in the chart application by selecting Menu > AIS Options > MARPA & AIS Options or the radar application by selecting Menu > Track Targets > MARPA & AIS Options.
13.13 AIS alarms 13.14 Buddy tracking The AIS functions generate a number of alarms to alert you to dangerous or lost targets. The Buddy Tracking feature enables you to add AIS-equipped friends and regular contacts to a “Buddy List” on your multifunction display. As soon as a vessel on your Buddy List sails into the range of your AIS unit, the vessel icon changes to indicate this. In addition to the dangerous target alarm, the system generates an alarm when a dangerous target becomes a lost target i.e.
i. Select Yes to enter a name for the buddy vessel ii. Select No to save the vessel to your buddy list without entering a name for the buddy vessel. The vessel will now be added to your buddy directory. Adding a vessel to your buddy list from AIS target list 1. If you are in the chart application, goto Menu > AIS Options. 2. If you are in the radar application, goto Menu > Track Targets > View MARPA & AIS Lists. 3. Select View AIS List. The AIS Target List is displayed. 4. Select an AIS target. 5.
Chapter 14: Waypoints, Routes and Tracks Chapter contents • 14.1 Waypoints on page 128 • 14.2 Routes on page 133 • 14.3 Tracks on page 136 • 14.
14.1 Waypoints Showing and hiding waypoint groups / symbols A waypoint is a position marked on the screen to indicate a site or a place to navigate to. As well as acting as position markers, waypoints are also the building blocks used to create routes. Common waypoint functions are accessed using the waypoints menu. This can be shown at any time by selecting WPT . Waypoint display examples Waypoints in the chart application In the chart application both active and inactive waypoints are shown.
• Stop Goto From the chart, radar or fishfinder application: 1. Select and hold the required location on screen. The context menu is displayed. 2. Select Place Waypoint. • Restart XTE • Advance Waypoint • Measure • Build Route • Acquire Target (only available if Radar overlay is switched on.) • Slew thermal camera (only available when thermal camera is connected and operating.) Accessing the context menu You can access the context menu by following the steps below. 1. New e Series or New c Series: i.
Navigating to a waypoint on the screen In the event that you steer off-track, you can go straight to your target by resetting XTE. Resetting Cross Track Error (XTE) While following a route in the chart application: 1. Select the route. The route context menu is displayed. 2. Select Restart XTE. Resetting XTE results in a new course from the current vessel position to the current target waypoint. This does not affect your saved route. D11753-2 From the chart or radar application: 1. Select the waypoint.
4. Use the on-screen keyboard to make the changes, then select the on-screen keyboard's SAVE button. Symbol Type Symbol Type Trawler Tree Triangle Wreck Editing a waypoint using the context menu 1. Select the waypoint. The waypoint context menu is displayed. 2. Select Edit Waypoint. The edit waypoint dialog is displayed. 3. Select the field you want to edit. 4. Use the on-screen keyboard to make the changes, and then select the on-screen keyboard's SAVE key.
Waypoint groups In order to make your waypoints easier to manage, you can organize them into groups of your choice. When fishing, for example, you may only wish to see the waypoints that indicate good fishing sites. Provided that you have not changed the default group, all waypoints are automatically placed in the default “My Waypoints” group when they are created. Note: A waypoint can only belong to one group. Displaying the waypoint group list From any application: 1. Select WPT. 2.
14.2 Routes A route is a series of waypoints typically used to assist with passage planning and navigation. A route is displayed on screen as a series of waypoints linked by a line. 1. Select and hold a location on screen. The chart context menu is displayed. 2. Select Build Route. The build route menu is displayed. 3. Select a location on screen to be the starting position. 4. Select relevant locations to place subsequent waypoints in order. The route is saved and displayed as each waypoint is placed. 5.
1. Use the Range In and Range Out buttons to range in and out of the chart. Adjusting chart range while building a route Route context menu Placing the cursor over a route in the chart application displays a context menu showing the leg of the route highlighted by the cursor and menu items. From the Build Route menu: 1. Use the on-screen Range In and Range Out icons to range in and out of the chart. Build a route from a track You can create a route from a recorded track.
• From a selected waypoint or any leg within a route. You can also follow any route in reverse order. Following a stored route From the chart application: 1. Select Menu. 2. Select Navigate. 3. Select Follow Route. The Route list is displayed. 4. Select the route you want to follow. 5. Select Follow Route. D12295-1 You can also reset the XTE from the Navigate Menu: Menu > Navigate > Restart XTE. Cancelling navigation of a route From the chart application: 1. Select the Route.
Moving a waypoint within a route 14.3 Tracks From the chart application: 1. Position the cursor over the waypoint you want to move. The waypoint context menu is displayed. 2. Select Move Waypoint. 3. Select the new location for the waypoint. A track is an on-screen trail that shows the passage you have taken. This trail is made up of a series of track points which are created automatically.
• Time— The track points are placed at regular intervals of time. • Distance— The track points are placed at regular intervals of distance. 5. Select the Track Interval and set to the appropriate value: • Units of time from the list displayed (available if “record track by” is set to time). • Units of distance from the list displayed (available if “record track by” is set to distance). • Not available — no Track Interval is available if the “record track by” is set to auto). • Erase a track.
14.4 Waypoints, routes and tracks storage capacity The display can store the following quantities of waypoints, routes and tracks Waypoints • 3000 Waypoints Routes • 150 routes, each consisting of up to 50 waypoints. Tracks • 15 tracks, each consisting of up to 10000 track points.
Chapter 15: Chart application Chapter contents • 15.1 Chart application overview on page 140 • 15.2 Chart ranging and panning on page 141 • 15.3 Vessel position and orientation on page 142 • 15.4 Chart views on page 144 • 15.5 Chart context menu on page 145 • 15.6 My Data options on page 146 • 15.7 Navigation options on page 146 • 15.8 Measuring distances and bearings on page 147 • 15.9 Chart vectors on page 147 • 15.10 Current information on page 148 • 15.
15.1 Chart application overview The chart application provides an electronic chart with passage planning and navigation features. It combines 2D and 3D viewpoints and provides a variety of cartographic information regarding your surroundings and charted objects. Typical uses for the chart application include : • Monitor your vessel location and heading. • Interpret your surroundings. • Measure distance and bearing. • Navigate using waypoints. • Plan, and Navigate using routes.
Navionics chartplotter sync connection 15.2 Chart ranging and panning You can wirelessly synchronize waypoints and routes between the multifunction display and a tablet or smartphone device. Ranging in and out 1 2 3 The table below shows the Range controls available for each display variant. 4 Rotary Control • New c Series • New e Series Range in and Range out buttons • New c Series Range in and Range out on-screen icons • New a Series D12166-2 1. Multifunction display. 2. Wi-Fi connection.
15.3 Vessel position and orientation Head-Up Vessel position on the chart display Your current position is represented on screen by the vessel symbol. The symbol used for your vessel will vary depending on the vessel type selected during initial set up of your multifunction display. Motor Vessels D12298-1 Sail Vessels Head Up mode displays the chart with your vessel’s current heading upwards. As the heading changes the vessel symbol remains fixed and the chart picture rotates accordingly.
Note: In the 3D chart view, only Relative Motion mode is available. Note: It is not possible to select True Motion when the orientation is set to Head Up. The current motion mode applies to the active instance of the chart application. When you pan the chart the motion mode is no longer active. This is indicated in the status bar by brackets around the motion mode — for example, (Relative Motion). This enables you to view another area of the chart whilst navigating.
15.4 Chart views 3D chart view Switching between 2D/3D chart view The 3D view can display a range of information to help you navigate. You can switch between 2D and 3D views. 1 From the chart application: 1. Select Menu. 2. Select Presentation . 3. Select Chart View to switch between 2D or 3D. 10 2D chart view 11 2 3 4 5 6 7 8 9 000°T The 2D chart view can display a range of information to help you navigate.
ii. New a series or New e Series — Swipe your finger up or down across the screen to adjust the pitch. D11755-1 15.5 Chart context menu Placing the cursor over an area in the chart application displays a context menu showing the cursors positional data and menu items. 4. To adjust the rotation: i. New c Series or New e Series — Move the Joystick Left or Right to adjust the rotation ii. New a Series or New e Series — Swipe your finger left or right across the screen to adjust the rotation.
15.6 My Data options 15.7 Navigation options The chart provides features to help you manage your data and help plan your navigation to a chosen location. The chart application provides features to help navigate to a chosen location. The options are found in the My Data menu: Menu > My Data. The navigation options are found in the Navigate menu: Menu > Navigate. • Waypoint List — View and edit waypoints stored on the system. • Route List — View and edit routes stored on the system.
15.8 Measuring distances and bearings You can use the databar and context menu information you can use the measure function to measure distances in the chart application. You can determine the distance and bearing: 15.9 Chart vectors Chart vectors display indicators for heading, COG, wind direction and tide direction. A range of vector graphics can be displayed in the chart application when in 2D chart view.
15.10 Current information 7. To set the animation date to 24 hours ahead of the current date select Next Day. Animated current information Displaying details of currents The electronic charts may allow animation of the current information current stations. From the chart application: 1. Select diamond-shaped current icon. The chart context menu is displayed. 2. Select Current Station. The current graph for the selected current station is displayed.
15.11 Tide information Tide graphs Tide graphs provide a graphical view of tidal activity. Animated tide information 1 The electronic charts may allow animation of the tide information tide stations. 2 3 4 Animated tide information is available in the chart application wherever a diamond-shaped symbol with a "T" is displayed: This symbol identifies tide stations and the availability of tide information for the location.
15.12 Chart object information You can display additional information on the chart for cartographic objects, ports, and marinas. 5. Select SEARCH. The search results are displayed. 6. Select an entry in the list to display more information. You can also search for the nearest instance of a particular chart object and search for ports by name.
15.13 Chart presentation • Radar — Overlay radar onto the chart (2D view only). The chart has a number of presentation options which affect the level of detail, types of objects and aspects of its operation. The presentation options available are: • NOWRad — Provides the NOWRad weather radar overlay, without the need to open a separate weather application window (2D view only). • Chart detail — Set the level of object detail shown on the chart.
Radar overlay NOWRad weather overlay You can combine the chart with the radar and MARPA functions to provide target tracking or to help you distinguish between fixed objects and other marine traffic. With a suitable weather receiver connected to your multifunction display, you can overlay NOWRad weather information on the chart display.
Safe Zone Ring Note: The chart application can display and configure a MARPA / AIS safe zone ring. The fuel range ring is an estimated range that can be reached at the current rate of fuel consumption, of the fuel onboard and based on a number of external factors which could either extend or shorten the projected range. This estimate is based on data received from external fuel management devices, or via the Fuel Manager.
3. Select Layers. 4. Select 3D Display Options. 5. Select Transducer Cone so that On is highlighted. Selecting Transducer cone will switch the function on and off. Enabling depth scale To enable a depth indicator at your vessels location follow the steps below: In 1. 2. 3. 4. 5. 3D view: Select Menu. Select Presentation. Select Layers. Select 3D Display Options. Select Depth Scale so that On is highlighted. Selecting depth scale will switch depth indicator on and off.
15.14 Chart set-up menu options The following table describes the various options in the Chart Set-up Menu for your multifunction display. Menu item Description Options Context Menu (Touchscreen displays only) Determines how the context menu is accessed using touch • Touch — touching a chart object opens the context menu. • Hold — Touch and holding on a chart object opens the context menu. Cartography Provides access to the Cartography menu options.
Cartography set-up menu options The following table describes the various options in the Cartography Set-up Menu for your multifunction display. Menu item Description Options Chart Display Determines the level of detail shown on the chart. • Simple • Detailed (default) • Extra Detailed Chart Grid Determines whether grid lines representing longitude and latitude are displayed on the chart: • Off • On (default) • Off — grid lines are NOT displayed. • On — grid lines are displayed.
Menu item Description Options Nav. Marks Determines whether navigation marks are displayed on the chart: • Off • Off — navigation marks are NOT displayed. • On (default) • On — navigation marks are displayed. Nav. Marks Symbols Light Sectors Determines which set of navigation mark symbols is used — International, or US. These symbols correspond to paper charts. • International (default) Determines whether the sector of light cast by a fixed beacon is displayed or not.
New a Series / New c Series / New e Series
Chapter 16: Radar application Chapter contents • 16.1 Radar overview on page 160 • 16.2 Radar scan speed on page 161 • 16.3 Radar scanner status symbols on page 161 • 16.4 Radar range and image quality on page 162 • 16.5 Radar display overview on page 164 • 16.6 Dual range radar operation on page 165 • 16.7 Radar mode and orientation on page 166 • 16.8 • 16.9 Radar adjustments: HD and SuperHD scanners on page 169 • 16.10 Radar adjustments: non-HD digital radomes on page 171 • 16.
16.1 Radar overview Radar is used to provide information that can help you to track targets and measure distances and bearings. Radio Detection And Ranging (RADAR) is used at sea to detect the presence of objects (known as ‘targets’) at a distance, and if they are moving, detect their speed. Radar works by transmitting radio pulses, then detecting reflections of these pulses (echoes) from objects in the area and displaying the reflections as targets on your display.
16.2 Radar scan speed 16.3 Radar scanner status symbols SuperHD open array radars with software version 3.23 or above or HD radomes support multiple scan speeds. The radar scanner power mode status is indicated in the databar. Radar scan speed is set up using the Radar Set-up menu.
2. Select Power up Radar to turn the radar on, or Power down Radar to turn the radar off. 3. Select Radar: Tx to start the radar transmitting, or Radar: Stdby to stop the radar transmitting. 16.4 Radar range and image quality Maximum radar range The usable range of the radar is limited by factors such as the height of the scanner, and height of the target.
Blind Sectors Obstructions such as funnels and masts near the radar antenna may obstruct the radar beam and cause radar shadows or ‘blind sectors’. If the obstruction is relatively narrow, there will be a reduction of the beam intensity, though not necessarily a complete cut-off. However, for wider obstructions there may be a total loss of signal in the shadow area. There may also be multiple echoes which extend behind the obstruction.
Sea clutter off 16.5 Radar display overview With your radar scanner connected and the radar in transmit mode, the radar picture provides a map-like representation of the area in which the radar is operating. 2 1 3 5 4 6 7 8 9 Sea clutter in auto 10 11 12 13 14 15 D12207-2 Interference When two or more radar-equipped vessels are operating within range of each other mutual radar interference can occur.
is dependent on many factors and may not necessarily be proportional to its physical size. Nearby objects may appear to be the same size as distant larger objects. Note: Colors stated above refer to the default color palette. With experience, the approximate size of different objects can be determined by the relative size and brightness of the echoes. You should bear in mind that the size of each on-screen target is affected by: 16.
16.7 Radar mode and orientation Scanner Dual Range mode Operating mode 4 Kw SuperHD Open Array Long SuperHD Short HD The radar can operate in a number of orientation modes to suit different types of navigation. Long SuperHD Short HD The orientation of the radar refers to the relationship between the radar and the direction that you are travelling in.
Course-Up 1 The default motion mode is “Relative”, with zero offset. N N 2 True Motion (TM) When the motion mode is set to True, fixed radar targets maintain a constant position and moving vessels (including your vessel) travel in true perspective to each other and to fixed landmasses on the screen. As the vessel’s position approaches the edge of the screen, the radar picture is automatically reset to reveal the area ahead. D12210-1 Item Description 1 Current course upwards.
16.8 Radar tuning: On-screen gain controls Touchscreen multifunction displays provide on-screen access to controls for Gain, Rain and Sea clutter. Gain control Rain control Sea control Note: non-touchscreen controls are accessed by the menu options: Menu > Rain and Menu > Adjust Gain. Enabling and disabling on-screen gain controls You can enable and disable the on-screen gain controls by following the steps below. On a touchscreen multifunction display, with the relevant application displayed. 1.
16.9 Radar adjustments: HD and SuperHD scanners You can use the gain presets and other functions to improve the quality of the radar picture. The following settings are available from the Radar menu and apply to HD radomes, HD and SuperHD open array scanners: Menu Item Description Options Auto Gain Mode The radar gain presets enable you to quickly select pre-configured settings to achieve the best picture in different situations.
6. Select the Auto box so that a tick is placed in the box for automatic gain control. Adjusting radar anti sea clutter From the radar application, with the required Auto Gain Mode selected: 1. Select Menu. 2. Select Adjust Gain , where shall be the Auto Gain mode already selected. 3. Select Sea: . 4. The Sea clutter slider bar control is displayed. 5. Adjust the Sea clutter slider bar control to the appropriate setting (between 0 and 100%), or 6.
16.10 Radar adjustments: non-HD digital radomes You can use the gain presets and other functions to improve the quality of the radar picture. The following settings apply to non-HD digital radomes and are available from the Radar menu: Menu Item Description Options Rain The radar scanner detects echoes from rain or snow. These echoes appear on screen as countless small echoes continuously changing size, intensity and position.
16.11 Radar presentation menu options Function Description Options Dual Range This menu item allows you to turn Dual range mode On and Off. • On • Off Dual Range Channel This menu item allows you to choose long or short channel for dual range.
Function Description Options Data Overlay Set-up This menu item contains a sub-menu which enables you to turn on and select information to display in data cells located on the bottom left of the radar application (Data cells will be displayed in all radar windows).
R ST IL LU RY 1 TE M PO 2 R A D R A AT IO N FT True motion mode example 3 4 D12745-1 1 Ships heading marker. 2 Target travelling at between 0 kt to 1 kt (Minimal to no wake). 3 Target moving in opposite direction to vessel (Wake appears in opposite direction to your vessel’s heading). 4 Target moving in same direction as vessel (Wake appears towards your vessel’s heading). Note: You may see a wake ‘ring’ around fixed targets due to small error factors such as rotation time delays.
16.12 Using radar to measure distances, ranges, and bearings Measuring using VRM/EBL Variable Range Markers (VRM) A Variable Range Marker (VRM) is a circle centred on your vessel’s position and fixed with respect to the heading mode. When this circle is adjusted to align with a target, its range from your vessel is measured and displayed on the Radar context menu when you select the VRM with the cursor.
VRM/EBL context menu The VRM/EBL function includes a context menu which provides positional data and menu items. 1. Position the cursor over the VRM/EBL. 2. Press the Ok button. The radar context menu is displayed. 3. Use the Rotary Control to select Float Center. 4. Press the Ok button. 5. Using the Joystick, move the center position of the circle to the desired position. 6. Press the Ok button to confirm the new position.
16.13 Using radar to track targets and avoid collisions The Guard Zone , VRM/EBL and MARPA functions will help you track targets and avoid collisions. With a radar connected to your multifunction display, you can: • Assess how far away a target is and its bearing (VRM/EBL). • Set an alarm to trigger when a target is within a specified zone (Guard Zone). • Display detailed information on tracked targets (MARPA). • Display the range and bearing of a target.
There are conditions where acquiring a target may become difficult. These same conditions may be a factor in successfully tracking a target. Some of the conditions are: • The target echo is weak. The target is very close to land, buoys or other large targets. • The target or your own vessel is making rapid manoeuvres. • Choppy sea state conditions exist and the target is buried in excessive sea clutter or in deep swells.
4. Select View MARPA List. 5. Select the relevant MARPA target from the list. 6. Select Cancel Target or Cancel All Targets. 5. Select the relevant target. 6. Select View Full Target Data. Vessel vectors (CPA graphics) overview CPA graphics show vectors for your vessel and a selected target. A vector is a line on-screen showing the predicted courses of your vessel and the selected target if you both remain on your present course.
16.14 Scanner set-up menu options The Scanner Set-up menu enables you to configure the performance and behavior of your radar scanner.
16.15 Resetting the radar To reset radar settings to defaults follow the steps below: From in the radar application: 1. Select Menu. 2. Select Scanner Set-up. 3. Select Advanced Set-up. 4. Select Reset Advanced. A confirmation pop up message is displayed. 5. Select Yes to confirm reset.
New a Series / New c Series / New e Series
Chapter 17: Fishfinder application Chapter contents • 17.1 How the fishfinder works on page 184 • 17.2 Raymarine sonar modules on page 184 • 17.3 Traditional sonar technology on page 185 • 17.4 Broadband CHIRP sonar technology on page 185 • 17.5 Fishfinder introduction on page 186 • 17.6 Transducer bandwidth on page 187 • 17.7 The sonar image on page 187 • 17.8 Fishfinder presets on page 188 • 17.9 Dual / Single frequency fishfinder on page 189 • 17.
17.1 How the fishfinder works 17.2 Raymarine sonar modules The fishfinder application uses a sonar module and a suitable sonar transducer. The sonar module interprets signals from the transducer and builds up a detailed underwater view. The table below lists Raymarine’s sonar modules and whether CHIRP technology is used. The transducer is located on the bottom of the boat, it sends pulses of sound waves into the water and measures the time it takes for the sound wave to travel to the bottom and back.
17.3 Traditional sonar technology Traditional sounders use a single carrier frequency or carrier wave for the sonar ping. These sounders work by measuring the time it takes the ping echo to return to the transducer to determine target depth. Using this method if 2 targets are close together they can be shown as a single large target, rather than multiple smaller targets 17.
17.5 Fishfinder introduction • Icon greyed-out - no fishfinder transducer is connected. Warning: Sonar operation Fishfinder context menu • NEVER operate the sonar with the vessel out of the water. The fishfinder application includes a context menu which provides fishfinder information and shortcuts to menu items. • NEVER touch the transducer face when the sonar is powered on. • SWITCH OFF the sonar if divers are likely to be within 7.6 m (25 ft) of the transducer.
17.6 Transducer bandwidth 17.7 The sonar image The fishfinder application displays the fishfinder frequency, center frequency or CHIRP mode depending on the connected sonar module and transducer. Interpreting the seabed using sonar Example of CHIRP sonar module in CHIRP mode. It is important to understand how to correctly interpret the seabed structure represented in the fishfinder display. The seabed usually produces a strong echo.
17.8 Fishfinder presets The fishfinder provides you with four preset configurations available from the fishfinder menu. These enable you to quickly select appropriate settings tailored for various situations. Each preset has been configured to provide the best operating parameters for the fishfinder. However, it is possible to manually adjust the presets if necessary.
17.9 Dual / Single frequency fishfinder 17.10 Non-CHIRP (traditional) sonar module frequency controls Dual frequency operation allows the sonar to operate and display 2 frequencies simultaneously. If the preset mode that you are using has two frequencies configured, you can view either one or both of those frequencies in separate windows. Selecting dual frequency view From the fishfinder application: 1. Select Menu. 2. Select Presets. 3. Select Dual. The main fishfinder menu is displayed. 4.
The graph above depicts an example of the fine tuning (from —50% to +50%) available when the frequency is set to 200 kHz. Tuning the fishfinder frequency (non-CHIRP sonar module) When connected to a non-CHIRP sonar module you can manually tune the fishfinder frequency. From the fishfinder application: 1. select Menu. 2. Select Frequency settings. 3. Select either Tune Freq 1 or Tune Freq 2 as required. The Tune Frequency slider bar is displayed: 17.
Frequency adjustment (CHIRP sonar module in non-CHIRP mode) When using a CHIRP sonar module in CHIRP mode (Low Chirp, Med Chirp or High Chirp) the frequency cannot be adjusted. When using a CHIRP sonar module in a non-Chirp mode (e.g. 50 kHz or 160 kHz) the frequency at which the transducer is transmitting can be adjusted. With the CHIRP sonar module set to a CHIRP mode (e.g. Low Chirp or High Chirp) the CHIRP sonar module will sweep the transducer’s available frequency range in each ping.
17.12 Fishfinder display modes Selecting a fishfinder display mode From the fishfinder application: 1. Select Menu. 2. Select Display Mode. 3. With dual frequency preset set, select Adjust to select which frequency display you wish to change. Selecting Adjust in Dual frequency preset will switch between Frequency 1 and Frequency 2. 4. Select the Select Mode menu item. 5. Select the required display mode: • None • Zoom • Bottom Lock • A-Scope 7. Select Back or use the Ok button to confirm the setting.
Bottom Lock The Bottom Lock function applies a filter to flatten the image of the seabed and make any objects on or just above it easier to discern. This feature is particularly useful for finding fish that feed close to the bottom. Bottom Lock is selected for individual fishfinder windows and can replace or appear alongside the standard fishfinder image. Adjusting the range of the bottom lock image allows you to view more bottom details.
Rotary Control • New c Series • New e Series 17.14 Fishfinder sensitivity settings The Sensitivity settings menu provides access to features and functions which enhance what is displayed on screen. Sensitivity options include: • Gain Range in and Range out buttons Slide the screen Up or Down • New c Series • Gain Mode — Only available when connected to a non-CHIRP sonar module including the internal sonar module.
4. Adjust the gain control to the required setting, or 5. Select Auto. A tick is displayed in the Auto box to signify automatic gain is enabled. Setting the auto gain mode for non-CHIRP sonar modules When using a non-CHIRP sonar module, from the fishfinder application: 1. Select Menu. 2. Select Sensitivity Settings. 3. Select Gain Mode. A list of available auto gain modes is displayed: • Cruising (Low) • Trolling (Med) • Fishing (High) 4. Select the required auto gain mode.
• Low CHIRP controls • Medium When connected to a CHIRP sonar module the automatic TVG has 3 modes: • High When connected to a Raymarine sonar module without CHIRP capabilities an automatic setting is available: • Auto Selecting the frequency for TVG adjustments When connected to a Raymarine CHIRP sonar module, the TVG for frequency 1 and frequency 2 can be changed independently or both at the same time.
Fishfinder color threshold 17.15 Fishfinder presentation options The color threshold setting determines the range of colors used on screen. The effect of this is to set a color threshold below which targets are not shown. For example a low setting would result in only the strongest (orange and red) targets being displayed. The Presentation menu gives you access to features and functions which provide additional on-screen functionality.
Menu Item Description Options bottom left corner of the screen: • Off • Select Data Category Select Data Category Allows selection of a data type by category. Data Cell 2 • Data Cell 2 • On • Select Data Category • Off • Data Cell 1 17.16 Depth and distance with the fishfinder The fishfinder display provides a number of features to help you determine depths and distances.
17.17 Fishfinder scrolling The fishfinder image scrolls from right to left. You can pause the scrolling or adjust the scroll speed, to ease placing of waypoints or VRMs on-screen. Scroll speed You can adjust the speed at which the fishfinder image scrolls. A faster speed provides more detail which may be useful when you are looking for fish. If you select a slower speed the information remains on the display for longer.
17.18 Fishfinder waypoints 17.19 Fishfinder alarms Placing a waypoint on the fishfinder display enables you to mark a position so that you can return to it later. The display can be configured to provide a number of fishfinder alarms. When a waypoint is placed, its details are added to the waypoint list and a vertical line labelled WPT is displayed on-screen. The waypoints can then be navigated to using the chart application.
17.20 Sounder set–up menu options This section describes the settings you can change using the sounder set up menu: (Menu > Set-up > Sounder Set-up). The set up menu contains settings that are likely to be changed infrequently. Menu Item Description Options Internal Sounder Switch the built in sonar on and off, for use when you have more than one multifunction display with internal sonar. • On • Off Note: Disabled on non-sonar variants. Note: Must be set to Off if an external sonar is connected.
17.21 Transducer set-up menu options The Transducer Set-up menu should be used when setting up your multifunction display for the first time or when installing a depth transducer. Menu Item Description Options Transducer Select the appropriate transducer type from those displayed. Some transducer may be detected by the system automatically. Options available are dependant on the sonar module connected. Speed Transducer Select the appropriate speed transducer from those available.
17.22 Resetting the sonar The reset function restores the unit to its factory default values. Note: Performing a factory reset will clear speed and temperature calibration settings and the depth offset. 1. Using a compatible Raymarine multifunction display go to the Fishfinder application page. 2. Select Menu from the side menu. 3. Select Set-up. 4. Select Sounder Set-up. 5. Select Sonar reset. 6. Select Yes to confirm. The unit will now be reset to factory default settings.
New a Series / New c Series / New e Series
Chapter 18: Data application Chapter contents • 18.1 Data application overview on page 206 • 18.2 Pre-configured datapages on page 206 • 18.
18.1 Data application overview 18.2 Pre-configured datapages The data application displays system and instrument data on your multifunction display. By default, a pre-configured range of data is displayed in a number of datapages. Each datapage consists of a number of 'cells', each containing a different item of data. The data application enables you to view numeric data generated by the system.
Datapage a65 / a67 / e7 / e7D Engine (Number of engines = 2) • Port Oil Pressure Engine (Number of engines = 3) e95 / e97 / c95 / c97 / e125 / e127 / c125 / c127 / e165 Datapage a65 / a67 / e7 / e7D Fuel • Port Coolant temperature e95 / e97 / c95 / c97 / e125 / e127 / c125 / c127 / e165 • Port Coolant temperature • Port Oil Pressure • Port RPM • Port Fuel remaining • Trim tabs • Starboard Coolant temperature • Starboard Oil Pressure • Starboard Oil Pressure • Starboard Coolant temperature
18.3 Customizing the data application You can customize the data application to show the system and instrument data that you require. In addition to displaying the default, pre-configured datapages in the data application, you can also: • Change the order datapages appear. • Customize datapages content to your specific requirements. • Rename the datapages. • Add new custom datapages. • Delete existing datapages. • Set the number of engines your vessel has (1 to 5). • Set the maximum engine RPM range.
Customizing datapage content From the data application: 1. Select Menu. 2. Select Edit Page. 3. Select the cell you want to change. 4. Select Select Data Category. 5. Select a data category. Selecting a data category will display a list of data items for that category. 6. Select the data item you want to display. Once selected a tick will be placed next to the data item in the menu and the cell on screen will display the new data item 7. Repeat steps 3 to 6 for all the data items you want to change.
Data Category Description Data Item Fuel Types of data related to the fuel system. For example, fuel levels. Fuel Level 1 (vol) Note: The options displayed are dependant on the number of engines set in the data application.
Data Category Description Data Item Navigation Types of data related to navigation. For example, bearing to waypoint. Cursor Position (Only available in the Databar and data overlay.) Digital Dial Graphical Cursor info Cross Track Error Rolling Road (Only available in the Data application.) Compass Target Position Bearing to Waypoint Distance to Waypoint WPT TTG Waypoint Info Pilot Pilot-related data. For example, rudder. Rudder Speed Speed-related data.
7. Select the data item you want to display. Once selected a tick will be placed next to the data item in the menu and the cell on screen will display the selected data item. 8. Repeat steps 3 to 6 for all the data items you want to change. 9. Select Rename Page. The on screen keyboard is displayed. 10. Enter the new name for the datapage. 11. Select SAVE. 4 Engines Deleting a datapage 5 Engines You can delete custom or pre-configured datapages from the data application.
Datapage and dial colors Datapage color theme and dial colors can be switched between light and dark. Color Theme Dial Color Light Light Light Dark Dark Dark Dark Light Example Resetting all datapages You can reset the datapages in the data application to the factory defaults. 1. Select Menu. 2. Select Reset All Pages. The confirm reset pop up message is displayed. 3. Select Yes to reset or No to cancel the action.
New a Series / New c Series / New e Series
Chapter 19: Thermal camera application — Pan and tilt cameras Chapter contents • 19.1 Thermal camera application overview on page 216 • 19.2 Thermal camera image on page 216 • 19.3 Controls overview on page 217 • 19.4 Camera control on page 218 • 19.5 Image adjustments on page 220 • 19.6 Pan and tilt camera — new camera interface on page 222 • 19.7 High power and high torque modes on page 225 • 19.
19.1 Thermal camera application overview The thermal camera application enables you to control a connected thermal camera and display its image on your multifunction display. 19.2 Thermal camera image The thermal camera provides a video image which is shown on your display. Thermal imaging (also known as infrared) cameras enable you to see clearly in low-light and no-light conditions.
Icon Description Rear-view mode — image is flipped horizontally. Zoom setting: 2x zoom. 19.3 Controls overview The thermal camera application is available on compatible Raymarine multifunction displays and systems. It includes controls for the thermal camera. Rotary control Zoom image in / out. Joystick • Pan and tilt camera Note: On touchscreen displays you can also use the touchscreen to pan and tilt the camera. Zoom setting: 4x zoom. Single active controller on network.
19.4 Camera control Panning and tilting, and the thermal image On a New e Series multifunction display you can pan and tilt the thermal camera image using the touchscreen. Power up and standby When the breaker connecting power to the camera is switched on, the camera will run a boot up sequence lasting for about 1 minute, after which the camera will be in Standby mode. In order for the camera to operate, you must bring the camera out of standby mode using the camera controls.
Surveillance mode settings The scan width determines the distance that the camera pans left and right when in surveillance mode. 1. Select Menu. 2. Select Camera Set-up. 3. Select Stabilization Mode. Selecting Stabilization mode switches stabilization On and Off. Scan Speed Thermal camera point mode The scan speed determines the speed at which the camera pans left and right when in surveillance mode. Point mode is only applicable to thermal cameras which have mechanical stabilization.
19.5 Image adjustments Thermal camera reverse video Adjusting the thermal camera image You can reverse the polarity of the video image to change the appearance of objects on-screen. With the thermal camera application displayed: 1. Select Menu. 2. Select Adjust Contrast. 3. Select the Contrast, Brightness, or Color option as appropriate. The relevant numeric adjust control is displayed. 4. Adjust the value as required. 5. Select Back or Ok to confirm the new value.
3. Use the Image Type menu item to switch between IR and Visible Light views, as appropriate. Thermal camera rear view mode The rear view mode flips the video image horizontally, providing a “mirror image”. This is useful for example in instances where the camera is rear-facing and you are viewing the image on a forward-facing monitor. Enabling thermal camera rear view mode With the thermal camera application displayed: 1. Select Menu. 2. Select Image Options. 3. Select Rear View.
19.6 Pan and tilt camera — new camera interface The thermal camera application menu options for a pan and tilt thermal camera with the new camera interface are shown below. Activate Camera Brings the thermal camera out of standby mode. (only available when camera is in standby.) Pause Image • On • Off (default) Camera Home Select to return the camera to its home position. Image Options Select to display the Image Options sub-menu.
Camera Set-up menu Set Home Position Sets the camera’s current position as the Camera Home position. Slew Settings Provides automatic slew options and camera alignment settings. • Auto Slew to MOB • Auto Slew to dangerous AIS target • Auto Slew to dangerous MARPA target • Camera height above sea level Align Camera Enables changes to camera’s horizontal alignment. Elev Align Enables changes to camera’s elevation (vertical) alignment.
Note: The thermal camera menu options available are dependant on the software version of your multifunction display and thermal camera. If options are different than listed above please refer to the manual that accompanied your thermal camera and / or the installation and operations handbook which accompanied your multifunction display.
19.7 High power and high torque modes Camera State Camera setting Dual payload Single payload Standby • High Power Mode ON 22 W 17.4 W 8W 7.4 W 13 W 13 W 8W 7.4 W 30 W 19.4 W 20 W 16.
19.8 Pan and tilt camera — old camera interface The thermal camera application menu options for a pan and tilt thermal camera with the old camera interface are shown below. Activate Camera Brings the thermal camera out of standby mode. (only available when camera is in standby.) Pause Image • On • Off (default) Camera Home Select to return the camera to its home position. Image Options Select to display the Image Options sub-menu.
System Setup Settings to optimize operation for this particular system / installation. About / Help Helpful information and restore to factory defaults setting. Exit Cancels on-screen menu. Surveillance mode menu Menu item / Description Scan Width Video setup menu Settings / Operation This setting determines the distance that the camera pans left and right when in surveillance mode. Select from: • Narrow — The camera will scan approximately 20º left and right of the center (40º total).
Menu item / Description Settings / Operation Set Stow Position This option sets the current position as the Stow position. The camera moves to the stow position whenever it is turned off or put into Standby mode. Name Camera Use this option to name the camera. Surveillance mode This options enables you to set the scan width and speed when in surveillance mode. Exit Exit to main menu.
Chapter 20: Thermal camera application — fixed mount cameras Chapter contents • 20.1 Thermal camera application overview on page 230 • 20.2 Thermal camera image on page 230 • 20.3 Controls overview on page 231 • 20.4 Camera control on page 232 • 20.5 Image adjustments on page 232 • 20.
20.1 Thermal camera application overview The thermal camera application enables you to control a connected thermal camera and display its image on your multifunction display. 20.2 Thermal camera image The thermal camera provides a video image which is shown on your display. Thermal imaging (also known as infrared) cameras enable you to see clearly in low-light and no-light conditions.
Icon Description Zoom setting: 4x zoom. Single active controller on network. Multiple active controllers on network. PC / laptop detected on network. 20.3 Controls overview The thermal camera application is available on compatible Raymarine multifunction displays and systems. It includes controls for the thermal camera. Rotary control Zoom image in / out. OK Confirm menu selection. Joystick Navigate menus. CANCEL / Back Cancel selection. RANGE IN / OUT Zoom image in / out.
20.4 Camera control 20.5 Image adjustments Power up and standby Adjusting the thermal camera image When the breaker connecting power to the camera is switched on, the camera will run a boot up sequence lasting for about 1 minute, after which the camera will be in Standby mode. With the thermal camera application displayed: 1. Select Menu. 2. Select Adjust Contrast. 3. Select the Contrast, Brightness, or Color option as appropriate. The relevant numeric adjust control is displayed. 4.
Thermal camera reverse video You can reverse the polarity of the video image to change the appearance of objects on-screen. The reverse video option (video polarity) switches the thermal image from white-hot (or red-hot if the color mode setting is active) to black-hot. The difference between white-hot and black-hot is shown below: White-hot thermal image. Black-hot thermal image. You may find it useful to experiment with this option to find the best setting to suit your needs.
20.6 Fixed mount camera menu The thermal camera application menu options for a fixed mount thermal camera are shown below. Activate Camera Brings the thermal camera out of standby mode. (only available when camera is in standby.) Pause Image • On • Off (default) Image Options Select to display the Image Options sub-menu.
JCU Icon PC Icon Shows or hides the on-screen JCU connected icon. • On (default) Shows or hides the on-screen PC connected icon. • On (default) • Off • Off Restore Factory Defaults Enables you to restore the camera’s settings to factory default values. Note: The thermal camera menu options available are dependant on the software version of your multifunction display and thermal camera.
New a Series / New c Series / New e Series
Chapter 21: Camera application Chapter contents • 21.
21.1 Camera application overview 2. Move the Joystick Up to display the previous video feed. You can view a camera or a video feed which is connected directly to your multifunction display using the video input(s) or IP camera feeds which are available on your network. The camera application can be set to cycle through all available feeds. If supported by your camera, you can adjust the brightness, contrast, color and aspect ratio of the video image. PAL / NTSC is selected automatically.
Note: In the steps above represents the default feed name provided by the connected device or the custom name which can be assigned to the feed. Turning off camera cycling You can turn off camera cycling using the methods detailed below. From the camera application, with camera cycling turned on: 1. Select Menu > Camera Cycling > Camera Cycling so that Off is highlighted, or 2. Change the camera / video feed manually as described earlier in this section, or 3.
New a Series / New c Series / New e Series
Chapter 22: Fusion link application Chapter contents • 22.1 Fusion link overview on page 242 • 22.2 Media sources on page 243 • 22.3 Browsing music on page 245 • 22.4 Selecting shuffle and repeat functions on page 245 • 22.5 Adjusting volume levels for each zone on page 246 • 22.6 Selecting the zone to control on page 246 • 22.7 Adjusting the tone controls on page 247 • 22.8 Selecting the system to control on page 247 • 22.
22.1 Fusion link overview • Play / Pause the current track. The multifunction display can control a connected 700 series Fusion entertainment system. • Select the zone to be controlled. (For information on setting up zones refer to the manual that accompanied your Fusion entertainment system. • Set Shuffle and Repeat functions.
22.2 Media sources DVD The layout and controls available are determined by the selected media source. iPod 1 2 3 2 3 1 4 4 5 6 D12748-1 1 Album artwork. 2 Track title. 3 Artist. 4 Track progress. 5 Track number. 6 Album title. 5 D12750-1 1 Time elapsed. Menu options available for iPods are as follows: 2 Title. • Browse music. 3 Chapter. • Repeat. 4 Remote button. • Shuffle. 5 DVD remote controls including: • Tone Controls. • Directional keypad. • Select Fusion System.
Selecting a media source Satellite radio You can select which media source you want to control. 1 3 4 D12752-1 1 Track name. 2 Artist. 3 Channel details. Menu options available for Satellite radio are as follows: • Tone Controls. From the Fusion link application: 1. Select Src:. A list of media sources is displayed. 2. Select the relevant media source. • Select Fusion System. VHF 1 2 3 D12753-1 1 Squelch control. 2 Channel. 3 Manual / Auto status.
22.3 Browsing music You can browse the music available on your connected iPod or USB device. From the Fusion link application: 1. Select the Menu icon. 2. Select Browse Music. The media device name is displayed. 3. Select the media device. The contents of the device are displayed. 4. Browse the available folders by selecting on them. 5. Select the Back icon to move back up the folder structure. 6. Select the track that you want to listen to. The main screen is displayed and the track will begin to play.
22.5 Adjusting volume levels for each zone 22.6 Selecting the zone to control The volume level for each zone can be adjusted individually or you can adjust all zones at the same time. From the Fusion link application: 1. Select Zone:. The zone selection bar is displayed. From the Fusion link application: 1. Select Vol:. The zone volume control is displayed. 2. Select the relevant zone. 3. Adjust the volume level to the required setting. 4. Select the Back icon to go back to the main screen.
22.7 Adjusting the tone controls 22.8 Selecting the system to control The Bass, Middle, and Treble tone controls can be adjusted. Where more than one Fusion entertainment system is connected you can select which system the Fusion link application will control. From the Fusion link application: 1. Select the Menu icon. 2. Select Tone Controls. 3. Select either Bass, Middle, or Treble. 4. Adjust the level to the required setting. 5. Select Back to go back to the menu options. 6.
22.9 Menu options Menu option Media sources Description Browse Music • iPod. • USB. Enables browsing of music stored on the device. • iPod. • Off • USB. • Folder — Repeats all songs in the current folder. • iPod. Switches track shuffle on and off. Repeat Shuffle • USB. Tone Controls • All devices. Enables adjustment of the following tone controls: • Bass. • Middle. • Treble. Select Fusion system • All devices. Enables you to select the Fusion entertainment system you want to control.
Chapter 23: Weather application (North America only) Chapter contents • 23.1 Weather application overview on page 250 • 23.2 Weather application set up on page 250 • 23.3 Weather application display overview on page 251 • 23.4 Weather map navigation on page 254 • 23.5 Weather context menu on page 254 • 23.6 Weather information on page 255 • 23.7 Weather reports on page 255 • 23.8 Animated weather graphics on page 256 • 23.9 Weather application menu options on page 257 • 23.
23.1 Weather application overview 23.2 Weather application set up The weather application overlays historical, live, and forecasted weather graphics on a world map. A number of steps must be completed before you can use the weather application for the first time. The weather application can only be used in North America and its coastal waters. • Your multifunction display must be connected to a Raymarine Sirius weather receiver.
23.3 Weather application display overview Symbol The weather application displays a range of graphics to indicate weather conditions and forecast information. 2 3 Lightning — a lightning symbol is shown at each cloud-to-ground strike: • Light (recorded in last 10–15 minutes.) The following diagram illustrates the main features of the weather application display: 1 Description • Medium (recorded in last 5–10 minutes.) 4 • Dark (recorded in last 0–5 minutes.
Historical (grey) Current (red) Forecast (orange) Wind speed symbols Description Hurricane (Category 1–5) The weather application uses a range of symbols to represent different wind speeds.
NOWRad precipitation color codes Reflectivity Intensity Rainfall (mm/hr) Rainfall (in/hr) NOWRad displays the type and level of precipitation: 85 7487.83 292.03 Color code Precipitation type Reflectivity Intensity 90 15376.51 599.69 Light green Rain (15 to 19 dBz) 95 31575.91 1231.46 Medium green Rain (20 to 29 dBz) 100 64841.98 2528.84 Dark Green Rain (30 to 39 dBz) 105 133154.6 5193.03 Yellow Rain (40 to 44 dBz) 110 273436.4 10664.
23.4 Weather map navigation 23.5 Weather context menu You can move around the weather map and place waypoints. The weather application includes a context menu which provides positional data and the option to view weather reports from the cursor location. When you open the weather application, a world map is displayed. If the system has a position fix for your vessel, the map will be centred on your location.
23.6 Weather information 23.7 Weather reports You can view weather information for: You can view a number of different weather reports to give you a comprehensive view of the weather. • a specific location • a surface observation station (when displayed) • Cities (when displayed) Your multifunction display shows weather reports for: • Tropical statements. • Marine warnings. Viewing weather data at a specific location • Marine zone forecasts.
23.8 Animated weather graphics You can view animated weather graphics to provide an indication of changing weather patterns. The animated weather option enables you to view an animation from the current time for: • NOWRad — weather radar 1 • Wind • Waves • Pressure — surface pressure D12297-1 Item Description 1 Watchbox alert box Viewing watchbox alerts You can view a watchbox alert at any time by following the steps below: From the weather application with a watchbox alert box displayed. 1.
23.9 Weather application menu options The following options are available from the weather application menu: Menu item Description Find Ship Selecting Find Ship will reset the display to show your vessel in the center of the screen. Display Graphics The Display Graphics menu allows to choose what graphics to Show or Hide in the weather application. Menu item Description Options Watchbox Alert The Watchbox Alerts menu allows you to turn alerts Off, or select a range.
23.10 Glossary of weather terms Term Definition Cold front The boundary between two different air masses where cold air pushes warm air out of the way and brings colder weather. Cyclone A large area of low atmospheric pressure, characterized by inward spiralling winds. A “low” also called a “depression”. Also the name used for a hurricane in the Indian Ocean and Western Pacific. Depression An area of low pressure. Also called a cyclone.
Term Definition Typhoon The name for a tropical storm originating in the Pacific Ocean, usually the China Sea. They are basically the same as the hurricanes of the Atlantic Ocean and the cyclones of the Bay of Bengal. Wave cyclone A storm or low pressure centre that moves along a front. Wave period The period is the time gap between successive waves and the longer the period the faster the waves travel.
New a Series / New c Series / New e Series
Chapter 24: Sirius audio application (North America only) Chapter contents • 24.
24.1 Sirius audio overview A connected, compatible Raymarine Sirius marine weather / satellite radio receiver can be controlled using the Sirius audio application. Note: A Sirius subscription is required to enable use of a Sirius marine weather / satellite radio receiver. To enable volume controls the Raymarine Sirius marine weather / satellite radio receiver also needs to be connected to a vessel entertainment system.
Chapter 25: Mobile applications Chapter contents • 25.1 Raymarine mobile apps on page 264 • 25.2 Enabling Wi-Fi on page 265 • 25.3 Enabling mobile apps on page 265 • 25.4 Setting up Wi-Fi security on page 266 • 25.
25.1 Raymarine mobile apps 1 2 3 4 Raymarine mobile apps enable viewing and control of your multifunction display via a compatible mobile device, using a Wi-Fi connection. Raymarine currently offers the following mobile apps: • RayView D12599-1 • RayRemote 1. Multifunction display. • RayControl 2. Wi-Fi connection (2 way – streaming or remote control). Note: Your multifunction display must have software version V3.15 or later in order to use mobile apps. 3. Compatible smartphone. 4.
25.2 Enabling Wi-Fi 25.3 Enabling mobile apps With the homescreen displayed: 1. Select Set-up. 2. Select System Settings. 3. Select Wireless Connections. 4. Select Wi-Fi > ON. Raymarine mobile apps must be enabled on your multifunction display before you can stream video or remote control your multifunction display via a tablet or smartphone device. Mobile applications With the homescreen displayed: 1. Select Set-up. 2. Select System Settings. 3. Select Wireless Connections. 4. Select Mobile apps. 5.
25.4 Setting up Wi-Fi security 25.5 Selecting a Wi-Fi channel You can encrypt the Wi-Fi connection on the multifunction display to prevent unauthorized devices from accessing the connection. The default encryption is WPA2. By default the multifunction display automatically selects an available Wi-Fi channel.
Chapter 26: Customizing your display Chapter contents • 26.1 Language selection on page 268 • 26.2 Boat details on page 269 • 26.3 Units set-up on page 270 • 26.4 Time and Date set-up on page 271 • 26.5 Display preferences on page 272 • 26.6 Data cell and databar customization on page 274 • 26.7 List of data items on page 275 • 26.
26.1 Language selection The system can operate in the following languages: English (US) English (UK) Arabic Bulgarian Chinese Croatian Danish Dutch Finnish French German Greek Icelandic Italian Japanese Korean Norwegian Polish Portuguese (Brazilian) Russian Spanish Swedish Turkish With the homescreen displayed: 1. Select Customize. 2. Select Language. 3. Select from the languages available.
26.2 Boat details You can customize various aspects of the display's functions to make them specific to your vessel. Menu item Description Options Boat Type You can change the appearance of the vessel in the chart application. Select the option that most closely resembles the type and size of your vessel. • Power Cruiser 1 (default) Note: When boat type is selected during the initial set up of the multifunction display the boat type shall determine the datapage configuration in the data application.
26.3 Units set-up You can specify your preference for the units of measurement that will be used in all applications. Menu item Description Options Distance Units The units of measure that will be used in all applications for the display of all values related to distance. • Nautical Miles • Statute Miles • Kilometers Speed Units The units of measure that will be used in all applications for the display of all values related to speed.
26.4 Time and Date set-up You can specify your preference for the way that time and date will appear in all applications. Menu item Description Options Date Format Allows you to specify the preferred format for the display of date information in all applications. • MM:DD:YY (Month, Day, Year) Allows you to specify the preferred format for the display of time information in all applications.
26.5 Display preferences You can specify your preference for general display behavior. Menu item Description Options Key Beep An audible sound can be made each time a button is pressed or the touchscreen is used. • ON (default) If set to On, the cursor will be automatically hidden after a period of no movement. If set to Off, the cursor will persist on the screen until moved.
Multiple brightness groups can be configured. This can reflect the physical location of the units on your vessel if required. For example, the units at your helm can be set to one group, and the units on the flybridge can be set to a different group. In this example, any brightness adjustments made to a unit at the helm would be automatically reflected in the other units at the helm but not on the flybridge.
26.6 Data cell and databar customization 7. Select Home or Back when completed. You can customize the data displayed in on-screen cells with a wide range of data. Customizable data is displayed in the databar, extended databar (HybridTouch displays only) or data cells areas of the screen. The databar, extended databar and data cells are available in all applications.
26.7 List of data items Depending on connected devices the categories of data available to display in the data application, data overlay, databar, and expanded databar are shown below. The following table shows the data items available by category. Data Category Description Data Item Boat Types of data generated by your vessel. For example, tank levels. Fresh Water Digital Dial Graphical Grey Water Black Water Live Well Trim Tabs (Only available in the Data application.) Depth Depth data.
Data Category Description Data Item Fuel Types of data related to the fuel system. For example, fuel levels. Fuel Level 1 (vol) Note: The options displayed are dependant on the number of engines set in the data application.
Data Category Description Data Item Navigation Types of data related to navigation. For example, bearing to waypoint. Cursor Position (Only available in the Databar and data overlay.) Digital Dial Graphical Cursor info Cross Track Error Rolling Road (Only available in the Data application.) Compass Target Position Bearing to Waypoint Distance to Waypoint WPT TTG Waypoint Info Pilot Pilot-related data. For example, rudder. Rudder Speed Speed-related data.
26.8 System set-up menus The system set-up menus enable you to configure your display and connected external devices. The following menus are available: Menu item Description Alarms Enables you to configure all the different types of alarms produced by the display and connected equipment. Pilot Controls Displays the Pilot Control dialog. Fuel Manager Displays the Fuel manager page Audio Controls Displays the audio controls pop-up.
Alarms menu Menu item Description Options MOB Data Type Determines whether Position or Dead Reckoning (DR) data is displayed. Assuming that your vessel and the MOB are subject to the same tide and wind effects, the Dead Reckoning setting normally gives a more accurate course. • Dead Reckoning When set to On, an alarm is triggered at the time you specify for the Alarm Clock Time setting. Alarm Clock Alarm Clock • Position (default) • Off (default) • On Alarm Clock Time • 00:00 (default) • 00.
Menu item Description Options • Deep Fish Limit — Specifies the upper value for the Fish Alarm Depth Limit. • 2 ft (or equivalent units) to the maximum of the transducer range Deep Fish Limit • 2 ft (or equivalent units) to the maximum of the transducer range Fuel Manager In the fuel manager alarm options you can switch the low fuel warning alarm on or off and specify the fuel level at which the alarm is triggered.
Ground trip resets menu This menu enables you to resets the chosen ground trip distance counter to zero. Menu item Description Ground Trip 1 Reset Resets the ground trip 1 distance counter to zero. Ground Trip 2 Reset Resets the ground trip 2 distance counter to zero. Ground Trip 3 Reset Resets the ground trip 3 distance counter to zero. Ground Trip 4 Reset Resets the ground trip 4 distance counter to zero. System settings menu • Satellite number.
Multiple data sources (MDS) overview Installations that include multiple instances of data sources can cause data conflicts. An example is an installation featuring more than one source of GPS data. MDS enables you to manage conflicts involving the following types of data: • GPS Position. • Heading. • Depth. • Speed. • Wind. Typically this exercise is completed as part of the initial installation, or when new equipment is added.
Data sources menu This menu enables you to select the external sensors and devices that will provide data to the display. Auto / manual selection Each dialog enables you to view and select your preferred data source. selection of data source can be manual or set to automatic: • Auto — the display will automatically select a device and attempt to resolve any data conflicts that may occur where there is more than one source of data for that particular data source (for example, multiple GPS receivers).
External devices menu This menu enables you to configure the external devices connected to the display. Menu item Description Notes Fishfinder Set-up Enables you to select an external transducer and configure the options for the unit, such as depth offset. Also enables you to configure the options for an internal or external sonar module. For an explanation of these options refer to the Transducer set-up menu options described in the Fishfinder section of this document.
Connections menu This menu enables you to connect wireless Bluetooth and Wi-Fi devices to the display. Menu item Description Options Bluetooth Enable or disable Bluetooth on the display. • On • Off (default) Wi-Fi Enable or disable Wi-Fi on the display. • On • Off (default) Connection Manager Provides a list of Bluetooth devices in range. When you highlight a connection in the list and press OK, the following options are available: • Unpair / Forget this device • Audio control On / Off.
NMEA Set-up menu This menu enables you to configure settings for NMEA devices. Menu item Description Options Bridge NMEA Heading If set to ON, NMEA heading data will be bridged onto the SeaTalk data bus, and will be sent to all NMEA-connected devices. If set to OFF, NMEA heading data will NOT be bridged onto the SeaTalk bus.
System preferences menu Menu item Description Options Bearing mode Determines how all bearing and heading data is displayed in. This does not affect how the chart or radar displays are drawn. • True (default) This setting compensates for the naturally occurring offset of the earth's magnetic field. When set to Auto, the system automatically compensates, and displays the compensation value in brackets.
Maintenance menu This menu provides access to systems settings reset and diagnostics. Menu item Description Touchscreen Alignment If the touchscreen is misaligned to your touch, you can realign it to improve the accuracy. Realignment involves a simple exercise to align an on-screen object with your touch. For best results, perform this exercise when your vessel is anchored or moored. Options Note: The Touchscreen alignment option is not required on New c Series displays.
Diagnostics menu If you encounter problems with your multifunction display or peripheral devices you can use the Diagnostics menu to view information about your device and connected equipment. Select Device Enables you to a list of all devices connected to the SeaTalkhs network. You can also select an item in the list to view further details for that device. • Device • Serial No.
New a Series / New c Series / New e Series
Chapter 27: Maintaining your display Chapter contents • 27.1 Service and maintenance on page 292 • 27.
27.1 Service and maintenance 27.2 Cleaning This product contains no user serviceable components. Please refer all maintenance and repair to authorized Raymarine dealers. Unauthorized repair may affect your warranty. Best cleaning practices. Routine equipment checks Raymarine strongly recommends that you complete a number of routine checks to ensure the correct and reliable operation of your equipment.
Chapter 28: Troubleshooting Chapter contents • 28.1 Troubleshooting on page 294 • 28.2 Power up troubleshooting on page 295 • 28.3 Radar troubleshooting on page 296 • 28.4 GPS troubleshooting on page 297 • 28.5 Sonar troubleshooting on page 298 • 28.6 Thermal camera troubleshooting on page 299 • 28.7 System data troubleshooting on page 300 • 28.8 Video troubleshooting on page 301 • 28.9 Wi-Fi troubleshooting on page 302 • 28.10 Bluetooth troubleshooting on page 303 • 28.
28.1 Troubleshooting The troubleshooting information provides possible causes and corrective action required for common problems associated with marine electronics installations. All Raymarine products are, prior to packing and shipping, subjected to comprehensive test and quality assurance programs. However, if you experience problems with the operation of your product this section will help you to diagnose and correct problems in order to restore normal operation.
28.2 Power up troubleshooting Problems at power up and their possible causes and solutions are described here. Problem Possible causes Possible solutions The system (or part of it) does not start up. Power supply problem. Check relevant fuses and breakers. Check that the power supply cable is sound and that all connections are tight and free from corrosion. Check that the power source is of the correct voltage and sufficient current.
28.3 Radar troubleshooting Problems with the radar and their possible causes and solutions are described here. Problem Possible causes Possible solutions No Data or No scanner message Radar scanner power supply Check that the scanner power supply cable is sound and that all connections are tight and free from corrosion. Check relevant fuses and breakers. Check power source is of the correct voltage and sufficient current (using voltage booster if appropriate).
28.4 GPS troubleshooting Problems with the GPS and their possible causes and solutions are described here. Problem Possible causes Possible solutions “No Fix” GPS status icon is displayed. Geographic location or prevailing conditions preventing satellite fix. Check periodically to see if a fix is obtained in better conditions or another geographic location. GPS connection fault. Ensure that external GPS connections and cabling are correct and fault free. External GPS antenna in poor position.
28.5 Sonar troubleshooting Problems with the sonar and their possible causes and solutions are described here. Problem Possible causes Possible solutions Sonar data not available on multifunction display. Unit power supply fault. Check the unit power supply and cables. Other unit fault. Refer to the instructions supplied with the unit. SeaTalkhs / RayNet network problem. Check that the unit is correctly connected to a Raymarine network SeaTalkhs switch or crossover coupler (as applicable).
28.6 Thermal camera troubleshooting Problems with the thermal camera and their possible causes and solutions are described here. Problem Possible causes Possible solutions Video not displayed. Camera is in Standby mode. The camera will not display video if it is in Standby mode. Use the camera controls (either the thermal camera application or JCU) to “wake” the camera from standby. Problem with the thermal camera video connections.
28.7 System data troubleshooting Aspects of the installation can cause problems with the data shared between connected equipment. Such problems, their possible causes and solutions are described here. Problem Possible causes Possible solutions Instrument, engine or other system data is unavailable at all displays. Data is not being received at the display. Check the data bus (e.g. SeaTalkng) wiring and connections. Check the overall integrity of the data bus (e.g. SeaTalkng) wiring.
28.8 Video troubleshooting Problems with the video inputs and their possible causes and solutions are described here. Problem Possible causes Possible solutions No signal message on screen (video image not displayed) Cable or connection fault Check that the connections are sound and free from corrosion.
28.9 Wi-Fi troubleshooting Aspects of the installation can cause problems with the data shared between wireless devices. Such problems, their possible causes and solutions are described here. Problem Possible causes Possible solutions No wireless connection. Tablet / smartphone does not have a wireless connection established with the multifunction display. Ensure that Wi-Fi is enabled on the multifunction display (Homescreen: > Set-Up > System Settings > Wireless Connections > Wi-Fi > On).
28.10 Bluetooth troubleshooting Aspects of the installation can cause problems with the data shared between wireless devices. Such problems, their possible causes and solutions are described here. Problem Possible causes Possible solutions No wireless connection. iPhone does not have a Bluetooth connection established with the multifunction display. Ensure that Bluetooth is enabled on the multifunction display (Homescreen: > Set-Up > System Settings > Connections > Bluetooth > On).
28.11 Touchscreen troubleshooting Problems with the touchscreen and their possible causes and solutions are described here. Problem Possible causes Possible solutions Touchscreen does not operate as expected. Touch lock is enabled. Use the Joystick to turn off the touch lock on the home screen. Screen is not being operated with bare fingers, for example gloves are being worn. Bare fingers must make contact with the screen for correct operation. Alternatively you may use conductive gloves.
28.12 Miscellaneous troubleshooting Miscellaneous problems and their possible causes and solutions are described here. Problem Possible causes Possible solutions Display behaves erratically: Intermittent problem with power to the display. Check relevant fuses and breakers. • Frequent unexpected resets. • System crashes or other erratic behavior. Check that the power supply cable is sound and that all connections are tight and free from corrosion.
New a Series / New c Series / New e Series
Chapter 29: Technical support Chapter contents • 29.1 Raymarine customer support on page 308 • 29.
29.1 Raymarine customer support 29.2 Third-party support Raymarine provides a comprehensive customer support service. You can contact customer support through the Raymarine website, telephone and email. If you are unable to resolve a problem, please use any of these facilities to obtain additional help. Contact and support details for third-party suppliers can be found on the appropriate websites. Web support Sirius Please visit the customer support area of our website at: www.sirius.
Chapter 30: Technical specification Chapter contents • 30.
30.1 Technical specification New a Series physical specifications Dimensions e125 / e127 / c125 / c127 Physical specifications Dimensions • Width: 354 mm (13.94 in.) • Width: 163.57 mm (6.44 in) • Height (NOT including bracket): 222 mm (8.74 in.) • Height (NOT including bracket): 143.47 mm (5.65 in) • Height (including bracket): 256 mm (10.08 in.) • Height (including bracket): 162.72 mm (6.41 in) • Depth (NOT including cables): 69 mm (2.72 in.) • Depth (NOT including cables): 74.
e7 / e7D Power specification Full brightness: Power consumption Nominal supply voltage 12 V dc • c125 — 16.3 W Operating voltage range 10.8 V dc to 15.6 V dc • c127 — 20.8 W Fuse / Breakers In-line fuse (fitted within power cable) • e125 — 27.6 W • e127 — 33.5 W • 7 A. (Standard 20 mm glass fuse) Power consumption PowerSave mode: Full brightness: • c125 —6.1 W • e7 — 10 W • c127 — 14.6 W • e7D — 13.8 W • e125 — 10.9 W PowerSave mode: • e127 — 17 W • e7 — 4.
Viewing angle Maximum allowable wrongly illuminated pixels • Left / Right: 60 degrees Data connections • Top / Bottom: 60 / 50 degrees Wired connections 5 NMEA 0183 2x NMEA 0183 ports: • NMEA port 1: Input and output, 4800 / 38400 baud e7 / e7D Display specification Size 7 in.
Video specification Signal type Composite Format PAL or NTSC Connector type BNC (female) Output resolution 720p Electronic chart specification Embedded electronic charts Navionics worldwide base map. Compatible chart cards • Navionics Ready to Navigate • Navionics Silver • Navionics Gold • Navionics Gold+ • Navionics Platinum • Navionics Platinum+ • Navionics Fish'N Chip • Navionics Hotmaps Refer to the Raymarine website (www.raymarine.com) for the latest list of supported chart cards.
New a Series / New c Series / New e Series
Chapter 31: Spares and accessories Chapter contents • 31.1 Transducer accessories on page 316 • 31.2 RayNet connector network cables on page 316 • 31.3 SeaTalkhs network cables on page 317 • 31.4 SeaTalkhs patch cables on page 317 • 31.5 Video cables on page 318 • 31.6 a65 / a67 spares on page 318 • 31.7 e7 e7D spares on page 319 • 31.8 e95 / e97 / c95 / c97 spares on page 319 • 31.9 e125 / e127 / c125 / c127 spares on page 320 • 31.
31.1 Transducer accessories Item Part number Notes P48 sonar transducer A102140 Transom mount. P58 sonar transducer A102138 Transom mount. 1 m (3.28 ft) Minn Kota transducer adaptor cable A62363 Only for direct connection to sonar variant multifunction display. 0.5 m (1.64 ft) transducer adaptor cable E66066 316 For connecting any 600 watt sonar module-compatible sonar transducer directly to a sonar variant multifunction display. 31.
31.3 SeaTalkhs network cables Cable 1.5 m (4.9 ft) cable Part number SeaTalkhs network E55049 5 m (16.4 ft) SeaTalkhs network cable E55050 10 m (32.8 ft) SeaTalkhs network cable E55051 20 m (65.6 ft) SeaTalkhs network cable E55052 Spares and accessories 31.4 SeaTalkhs patch cables Cable Part number 1.5 m (4.9 ft) SeaTalkhs patch cable E06054 5 m (16.4 ft) SeaTalkhs patch cable E06055 patch cable E06056 15 m (49.2 ft) SeaTalkhs patch cable A62136 20 m (65.
31.5 Video cables 31.6 a65 / a67 spares The following video cable is required for the video in / out connector on the e95 / e97 / e125 / e127 variant multifunction displays. Part number Description R70003 e-series accessory video cable 318 Notes Item Part number Trunnion (bracket) mount kit R70147 Front bezel R70148 Suncover R70149 Power cable 1.5m R70157 1.5 m (4.
31.7 e7 e7D spares Item Part number Trunnion (bracket) mount kit A62358 Documentation pack R62378 Flush mount panel set R62376 Front bezel R62377 Suncover R62365 1.5 m (4.9 ft) Straight power and data cable 1.5 m (4.9 ft) Right angled power and data cable Spares and accessories 31.
31.9 e125 / e127 / c125 / c127 spares Item Part number c/e series trunnion kit Item Part number R70002 e165 trunnion kit A80176 c/e series front bezel R7006 e165 front bezel R70126 c/e series suncover R70007 e165 suncover R70127 c/e/ series rear bezel R70028 e165 flush mount kit R70125 c.e series gasket R70080 R62379 Mounting adaptor kit — C120W/E120W R70009 1.5 m (4.9 ft) Straight power and data cable R70029 Mounting adaptor kit — C120/E120 R70011 1.5 m (4.
Appendix A NMEA 0183 sentences The display supports the following NMEA 0183 sentences. These are applicable to NMEA 0183 and SeaTalk protocols.
Appendix B NMEA 2000 sentences The display supports the following NMEA 2000 sentences. These are applicable to NMEA 2000, SeaTalkng and SeaTalk 2 protocols.
Message number Message description Transmit Receive Bridge 130306 Wind data ● ● ● 130310 Environmental parameters ● ● ● 130311 Environmental parameters ● 130576 Small craft status ● 130577 Direction data 130578 Vessel speed components NMEA 2000 sentences ● ● ● ● 323
Appendix C Connectors and pinouts Pin Signal Power, data, and video connector 8 Not connected 9 Screen 10 Not connected 4 9 1 8 10 2 7 11 3 Note: Use only Raymarine RayNet cables when connecting SeaTalkhs devices. 6 5 D12186-1 SeaTalkng connector Item Remarks Identification PWR / NMEA / Video Connector type 11 pin twist-lock Current source to network No current sourced for external devices Current sink from network 5 6 4 • Video: No power required for interface.
PIN Signal 13 VIDEO IN2 RTN 14 RED RTN 15 RED Appendix D Switch panel application Vessel control and monitoring systems When integrated with a vessel control and monitoring system your multifunction display can provide monitoring and controls for your power circuits, breakers, switches and equipment. The Switch Panel application can be used to: • Show the status of power circuits, breakers, switches and other equipment. • Apply power to each circuit individually. • Reset tripped breakers.
3. Insert the memory card into the card reader on your multifunction display. 4. From the homescreen select Set-up. 5. Select System Settings. 6. Select External Devices. 7. Select Switch Panel Set-up. 8. Select Install Config File. 9. If prompted select the memory card slot that contains your configuration file. The file browser is opened. 10. Select the configuration file. 11. Select OK.
Appendix E Software releases Raymarine regularly updates its multifunction display software to introduce improvements, additional hardware support and user interface features. The table below details some of the important enhancements and which software revision they were introduced with. Software version Applicable product manual Multifunction displays compatibility V6.
Software version Applicable product manual Multifunction displays compatibility Changes • Enhanced home screen customize option permitting 9 and 12 inch MFDs to view up to 4 applications on a single page. • Default Fuel data page added. • Added Arabic language support. • Inclusion of Remote Upgrade Utility to permit the upload of software to peripheral Raymarine products using SeaTalkng / SeaTalkhs. • Display of Aids To Navigation (AToNs) AIS targets when data received on either SeaTalkng or NMEA 0183.
www.ra ym a rin e .
