Distributed by Any reference to Raytheon or RTN in this manual should be interpreted as Raymarine. The names Raytheon and RTN are owned by the Raytheon Company.
HSB Series Chartplotter owner’s handbook Document number: 81150_1 Date: 18th September 1998
HSB Series Chartplotter HSB Series Chartplotter Installation and Operation Handbook SAFETY NOTICES 1. HIGH VOLTAGE. The display unit contains high voltages. Adjustments require specialised service procedures and tools only available to qualified service technicians – there are no user serviceable parts or adjustments. The operator should never remove the display unit cover or attempt to service the equipment. 2. NAVIGATION AID. This unit is only an aid to navigation.
HSB Series Chartplotter RAYTHEON MARINE products are supported by a network of Authorized Service Representatives.
iii Preface Preface This handbook covers the chart aspects of the following HSB Series systems from Raytheon: System Display Chartplotter Radome Chartplotter Raychart RC520 Yes No Combined Pathfinder Radar/Chartplotter Systems RL72RC RL70RC Yes 2D 18" RL74RC RL70RC Yes 4D 24" Repeater Displays Repeater RL70 Repeater RL70RC Repeater RC520 No Yes Yes – – – It contains very important information on the installation and operation of your new equipment.
iv HSB Series Chartplotter
Contents v Contents Chapter 1: Overview.............................................................. 1 1.1 Introduction ....................................................................... 1 How this Handbook is Organised .................................... 1 Terminology .................................................................. 2 General ............................................................................. 2 Display Unit Features ......................................................
vi HSB Series Chartplotter 2.3 Using Chart Cards ........................................................... 17 Inserting a Chart Card ...................................................... 17 Displaying the Chart Data ................................................. 18 Displaying Chart Information ............................................. 19 Removing a Chart Card .................................................... 19 2.4 Controlling the Display .....................................................
Contents vii Placing a Waypoint .......................................................... 45 Selecting a Waypoint ....................................................... 46 Waypoint Data Display ..................................................... 47 Editing the Waypoint Details ............................................. 47 Erasing a Waypoint .......................................................... 48 Moving a Waypoint .......................................................... 49 3.
viii HSB Series Chartplotter 3.5 Transferring Waypoints and Routes .................................. 65 Displayed Seatalk Waypoints ....................................... 65 Managing Database Lists ............................................ 65 3.6 Using Tracks ................................................................... 67 Setting Up a Track ........................................................... 68 Clearing the Current Track ................................................
Contents ix Help ................................................................................ 86 Soft Keys......................................................................... 86 Key Beep ........................................................................ 86 MOB Data ....................................................................... 86 Menu Timeout Period ....................................................... 86 Units .....................................................................
x HSB Series Chartplotter Data Standards ..............................................................100 HSB ..........................................................................100 SeaTalk .....................................................................101 NMEA .......................................................................102 SeaTalk and NMEA Data Received and Transmitted ........103 6.5 Cable Runs ....................................................................105 Power Cable ..
Contents xi 7.2 Resetting the System ......................................................118 7.3 Problem Solving..............................................................119 Common Problems and Their Solutions ...........................119 How to Contact Raytheon (US) ........................................119 For Marine Product and Services Information ...............119 For Accessories and Parts ..........................................119 For Technical Support: ................................
xii HSB Series Chartplotter
1 Chapter 1: Overview 1.1 Introduction How this Handbook is Organised This handbook describes the HSB Series Chartplotter RC520 and the charting functions of the combined Radar/Chartplotter RL70RC (refer to the Pathfinder HSB Series Radar Handbook, also provided with the combined system, for details on the radar functions). If you are using any HSB series 7" display unit as a chart repeater display you should refer to this handbook.
2 HSB Series Chartplotter General Note: Installation of all HSB display units is the same, whether the unit is a chartplotter or a radar display. If you have both the HSB Series Pathfinder Radar or the HSB Series Chartplotter Handbook you can refer to either handbook for display unit installation details. Terminology The following terminology is used to describe chartplotter and radar systems: Master A unit capable of sourcing specific data (such as radar or chart data).
3 General Chapter 1: Introduction Dedicated keys Trackpad Soft keys Dedicated keys D4266-1 The HSB (High Speed Bus) connection enables transfer of data between two compatible units. For example, the chart data is transferred from the chartplotter (the master display) via the HSB connection and can be displayed and controlled on any other HSB display (repeater display).
4 HSB Series Chartplotter Display Unit Features Display Unit Features & Functions • Uses position information from GPS, dGPS or Loran-C technology • Displays chart information from the C-MAP NT® chart cards (C-Cards) • Displays and transfers Seatalk, NMEA and HSB data • Provides full control of data from other HSB instruments • Three full-screen operating modes: Radar, Chart, Data Log (if appropriate data is available) • View radar and chart simultaneously and synchronise radar image with chart screen •
Chapter 1: Introduction 5 RR 1/2 3nm HEAD UP Chartplotter Display Operating Modes Radar Display Operating Mode for Stand Alone Units IR CURSOR BRG 000° RNG 0.220 nm HDG MODE TARGETS SCREEN Additional Modes for Linked Radar Units (or combined Radar/Chartplotter) RR 1/2 3nm HEAD UP IR HSB SeaTalk DISPLAY CURSOR BRG 000° RNG 0.
6 HSB Series Chartplotter Operating Modes In addition, in chart or radar full-screen mode you can set Windows On to split the display into two half-screen windows for supplementary data display as described below. The upper window shows the selected mode (chart or radar); operating control defaults to the upper window, but you can switch control between the radar and chart window with a single key-press.
7 1.2 The Chartplotter Display The chartplotter includes a small-scale world map that can be used for route planning. Detailed navigation information is displayed when a chart card is installed. Once the position fix has been established, your vessel’s position, if on screen, is shown as a boat shape, pointing in the direction of the current heading (or COG if heading data is not available). If no heading or COG data is available, the vessel is shown as a circle.
8 HSB Series Chartplotter Chartplotter Display Options Chartplotter Display Options Set up options allow you to customise the chart by choosing what is, or is not displayed, how it is displayed (including language and units), heading mode and how the chartplotter operates with other HSB units. You can also view the cursor position and a variety of data from other equipment, e.g. speed, heading, depth, wind and tide information in a set of user-selectable data boxes.
Chapter 1: Introduction 9 You operate the chartplotter in a variety of ways; the control keys on the display unit are used with on-screen facilities such as pop-up menus. These include: • A trackpad providing up, down, left, right and diagonal control of an on-screen cursor. • Eleven dedicated (labelled) keys. • Four soft keys with labels displayed on the screen. • Pop-up menus, displayed on-screen, from which you select options. • Database lists, displayed on-screen, which enable you to edit items.
10 HSB Series Chartplotter Trackpad and Cursor Trackpad and Cursor The trackpad and has several functions: • To move the cursor around the chart screen • To select an item from a pop-up menu or database list • To adjust a variable soft key control • To enter names in database lists You can press on any of the four sections of the trackpad to move the cursor in that direction (up, down, left or right), or press two sections at the same time to move diagonally.
11 POS Vessel’s position RTE Route Leg TIDE Tide vector WPT Waypoint Some items on the chartplotter screen, such as waypoints and chart objects have information associated with them. When you place the cursor over such objects, the information is displayed in a data box. In addition, soft keys are displayed for certain items. For example, when you place the cursor over a waypoint, the waypoint soft keys are displayed. The context-sensitive cursor allows you to move databoxes.
12 HSB Series Chartplotter Soft Keys, Pop-up Menus & Database Lists Soft Keys The four keys below the screen are called soft keys because their functions change according to the operation. The soft keys are grouped into related sets and subsets providing access to the various functions. The soft key labels are displayed on the screen just above the keys. The default soft keys are displayed until you press a key, or select an item on the screen; the soft keys associated with the action are then displayed.
Chapter 2: Getting Started 13 Chapter 2: Getting Started & Adjusting the Display This chapter provides information, instructions and a simple exercise to get you started using the HSB Series Chartplotter display unit. It also provides some typical scenarios that guide you through the common chartplotter functions. This chapter will help you to become familiar with the controls before you start using the chartplotter for routine navigation.
14 HSB Series Chartplotter 2.2 Switching the Display Unit On and Off This section explains how to switch the chartplotter display on and off. The following description assumes that there is no radar scanner connected to the chartplotter. Switching the Display Unit On/Off ➤ To turn the chartplotter display on, press and hold the POWER key until the unit beeps.
Chapter 2: Getting Started 15 Changing the Lighting and Contrast You can change the level of backlighting and contrast for the screen and the keys. The key lighting is set the same as the display lighting, except that it remains switched on at its lowest level even when the screen lighting is turned off, so that you can always find the keys. 1. Press the MULTI key to display the soft key controls: O F F 50% LIGHT CONTRAST D4161-1 The last-used soft key is highlighted in inverse video.
16 HSB Series Chartplotter Chart Simulator When the simulator is switched on, your initial simulated position is wherever the cursor was positioned. If you wish to practice using the chartplotter in a particular chart area, use the trackpad to pan to the chart area, then switch simulator ON.
Chapter 2: Getting Started 17 The chartplotter has a built-in world map that can be used for route planning. Most areas are covered on a scale of about 500nm per inch on the screen (200nm per cm), although some populated areas have details down to 300nm on the screen. To use the chartplotter as a navigation aid, charts with detailed information for the area you wish to navigate are required.
18 HSB Series Chartplotter 5. Close the card cover so that is clicks shut, to prevent water entering the display unit. Displaying the Chart Data D4158-1 Displaying the Chart Data The new chart information will be displayed when you move the cursor into an area covered by the new chart or, if it is already in the area, change the range scale. If a chart repeater is connected, the chart is also displayed on the repeater display.
Chapter 2: Getting Started 19 Displaying Chart Information ➤ To obtain the chart object, port or tide information: 1. Move the cursor over the symbol for which you require the information. An Object data box such as the following is displayed at the lower left corner of the screen: 1 Object Caution area D4260-1 2. To view further details, press ENTER. The details available are listed on-screen in an object information pop-up.
20 HSB Series Chartplotter 2.4 Controlling the Display You control the chart display using the cursor and control keys. You start all operations with the default soft keys shown below displayed (this is referred to as the default screen in the following sections).
21 Selecting the Mode of Operation Chapter 2: Getting Started D4283-1 The selected is mode is shown by a greyed icon and black border, it is displayed on the screen. The associated half-screen window soft keys are also displayed. 2. When the required mode is selected, press ENTER or CLEAR. The pop-up soft keys are cleared and the default soft keys are displayed. 3. When you press DISPLAY again, the pop-up and soft keys for the current full-screen mode are shown.The selected mode is shown full-screen.
22 HSB Series Chartplotter Selecting a Half-screen Window for Display ➤ To select a window: 1. From the full-screen Chart (or Radar) mode, press the DISPLAY key. Selecting the Mode of Operation The following soft keys are displayed with an image of each available window: DISPLAY WINDOWS OFF ON SELECT WINDOW D4156-2 2. To select a window, press either SELECT WINDOWS soft key until the required window is highlighted (if necessary, this will toggle windows on), then press ENTER. WINDOWS OFF ON 3.
Chapter 2: Getting Started 23 BDI Window Selecting the Mode of Operation CDI Window WINDOWS OFF ON SELECT WINDOW Navdata Window WINDOWS OFF ON WINDOWS OFF ON SELECT WINDOW Radar Window SELECT WINDOW WINDOWS OFF ON SELECT WINDOW D4271-1
24 HSB Series Chartplotter Returning to the Full-Screen Display In an emergency, you may wish to return to full-screen display mode. You can turn windows off, as described above. Alternatively, to return to full-screen display without data boxes or windows: Moving Around the Chart ➤ Press and hold the DISPLAY key for 2 seconds to return to the currently selected full-screen display. Moving Around the Chart You will normally operate the chartplotter with the chart showing your vessel’s current location.
Chapter 2: Getting Started 25 ➤ To move your vessel’s position off-centre: 2. Press ENTER to take control of the chart position. The letters POS are now in inverse video, and the cursor symbol has changed to a four-way arrow. This indicates that the cursor can be used to move the chart in any direction. D4278-1 3. Use the trackpad to move the cursor to the required position. 4. Press ENTER to select the position and return to normal cursor control.
26 HSB Series Chartplotter Centre the Vessel ROUTE GOTO SCREEN FIND SHIP D4160-1 When you press FIND SHIP the following occur: FIND SHIP • The chart is re-drawn with the vessel’s position in the centre. Moving Around the Chart • The cursor is homed onto the vessel position and moves with it. • When the vessel moves near the edge of the chart window, the chart is redrawn to place the vessel and cursor at the centre again.
Chapter 2: Getting Started 27 • To move the display to another area of the chart, by zooming out to a small scale chart, then zooming in on another position Increases the chart distance Vertical distance displayed on chart RANGE Decreases the chart distance 6nm CSR POS 50 45'980N 001 01'490W Status Bar D4175_1 ➤ To change the scale quickly, press and hold the required arrow on the RANGE key.
28 HSB Series Chartplotter Chart Boundary indicates further detail is available inside Moving Around the Chart D4279-1 4. When no further chart detail is available, as you press the bottom of the RANGE key, the effect depends on whether Plotter Mode is on or off as follows: • If Plotter Mode is Off, the unit beeps three times and the chart scale remains unchanged, indicating the smallest chart scale is displayed.
Chapter 2: Getting Started 29 Customising the Screen Presentation Options The SCREEN soft key lets you set the following screen presentation options on or off: CHRT GRID DATABOXES OFF ON OFF ON CUSTOM OFF ON D4177-1 Cursor Data Box On and Off The cursor data box provides the cursor’s position. If you wish to see a full chart, you can switch the data box off. The cursor data can be set up to appear in two data boxes; one showing range and bearing, the other showing latitude and longitude.
30 HSB Series Chartplotter The default data box positions are along the bottom of the chart. Each box can be moved to the required position on the screen using the context-sensitive cursor. Customising the Screen At any time, you can switch the group of data boxes on or off using the SCREEN soft key. When first installed, the boxes are all OFF. When the display unit is switched off and on again, the data boxes return to their last-used states (On or Off) and positions.
Chapter 2: Getting Started 31
32 HSB Series Chartplotter
Chapter 2: Getting Started 33 2.5 Typical Scenarios Typical Scenarios Each scenario indicates the key presses required to perform particular tasks. A typical chartplotter screen image is shown for each task. The scenarios assume you have read the previous sections of this chapter and that you are familiar with the Operating Controls. Full operating details for each function are provided in Chapters 3 and 4.
34 HSB Series Chartplotter Place and Goto A Waypoint 1 Place & Goto a Waypoint Add & Goto a Waypoint 1. Press MARKS 2. Position Cursor as required 2 Press the soft key 3 Press the soft key to go to the waypoint selected by the cursor.
Chapter 2: Getting Started 35 4 Place & Goto a Waypoint Add & Goto a Waypoint The vessel navigates towards the target waypoint See: 3.2 Working wth Waypoints Go to an individual Target Point, page 63.
36 HSB Series Chartplotter Make and Follow a Route 1 GOTO SCREEN FIND SHIP Press the soft key Make & Follow a Route 2 MAKE ROUTE EDIT ROUTE CLEAR ROUTE MORE! Press the soft key 3 1. Position Cursor - in this example over an existing waypoint 2. Press the soft key 4 Position Cursor for next waypoint, then press soft key. Repeat to plot all waypoints in sequence.
Chapter 2: Getting Started 37 5 Make & Follow a Route Make & Follow a Route Press the soft key. The route becomes the current route. 6 ROUTE GOTO SCREEN FIND SHIP Press the soft key 7 GOTO CURSOR GOTO WAYPOINT FOLLOW ROUTE Press the soft key 8 The vessel starts to navigate to the first (target) waypoint in the route. STOP FOLLOW GOTO CURSOR RESTART XTE WAYPOINT ADVANCE See: 3.3 Working wth routes, Follow a route, page 61. Altering the route, page 62.
38 HSB Series Chartplotter Review Your Passage Plan 1 ROUTE GOTO SCREEN FIND SHIP Press the soft key EDIT ROUTE CLEAR ROUTE 2 MORE! Review Your Passage Plan Press the soft key REVERSE ROUTE SAVE ROUTE ROUTE LIST 3 MORE! Press the soft key 4 1. Use the trackpad to move selection bar over required route. 2. Press the soft key 5 Time defaults to ETA - and assumes the current time is the start time.
Chapter 2: Getting Started 39 Review Your Passage Plan See: Displaying Route Information page 55. Change the TIME to HOURS - the display indicates it will take 32 minutes to reach the destination. You can change the PLANNED SOG; the display updates to indicate TIME required at the planned speed.
40 HSB Series Chartplotter Displaying the Radar and Synchronising Radar & Chart 1 1. Press DISPLAY -- then press twice more to select RADAR. Identifying a Target 2. Press the soft keys to set windows ON. The Chart window is the default selection. 3. Press ENTER. 2 ROUTE GOTO MORE! RDR CHRT Press the soft key. You can control the chart cursor. SYSTEM SET UP! CHART SET UP! TRACK SET UP! GPS SETUP! 1. Press MENU. 3 2.
Chapter 2: Getting Started 41 Identifying a Target 4 1. Move selection bar over Radar/Chart Synch. 2. Press the soft key. 3. Press ENTER twice. 5 ROUTE GOTO MORE! RDR CHRT Press the soft key. 6 SCREEN FIND SHIP MORE! RDR CHRT Press the soft key to synchronise the chart & radar images. 7 The radar and chart windows are synchronised and the cursor is 'homed' on the vessel Move the chart cursor -- you can see chart cursor move on the radar screen.
42 HSB Series Chartplotter
DISPLAY Controls display mode windows. - Press for display mode and soft keys display. - Press again to cycle through display modes, and ENTER. - Press and hold for 2 seconds for full-screen display. WINDOWS OFF ON SELECT WINDOW Press soft keys to toggle half-screen window on/off and to select lower window, press ENTER to finish. MARKS - MOB Controls waypoint, and Man OverBoard function. - Press to display waypoint soft keys. - Press and hold for 2 seconds to activate or cancel MOB.
ROUTE MAKE ROUTE GOTO PLACE WAYPOINT UNDO WAYPOINT GOTO WAYPOINT ACCEPT ROUTE Use the soft keys to set up a series of waypoints as a route. Use the trackpad to move the cursor then press PLACE WAYPOINT, continue until the route is complete. Press ACCEPT ROUTE to finish. EDIT ROUTE PLACE WAYPOINT UNDO WAYPOINT GOTO WAYPOINT Use to navigate to a waypoint selected from the waypoint database list. Use the trackpad to select the waypoint then press the soft key to start the GOTO.
Chapter 3: Waypoints, Routes and Tracks 43 Chapter 3: Waypoints, Routes and Tracks 3.1 Introduction This chapter explains how to use the chart functions to navigate with your HSB Series display. It covers the following topics: • Working with routes, including creating a new route, managing routes using the route database and editing routes. • Going to waypoints and following routes. • Transferring Waypoints and Routes • Using tracks, including showing tracks, track set up and saving tracks.
44 HSB Series Chartplotter 3.2 Working with Waypoints Introduction The HSB series Chartplotter enables you to place up to 998 waypoints: a waypoint is a position entered on a chart as a reference, or as a place to go to. All waypoints placed on the chartplotter are stored in a waypoint database list which includes symbol, position, bearing, range and additional data.
45 Chapter 3: Waypoints, Routes and Tracks ➤ To access waypoint soft keys, press MARKS: PLACE WPT PLACE WPT AT CURSOR AT VESSEL WAYPOINT LIST D4169-1 Placing a Waypoint The Place and Goto a Waypoint Scenario in Chapter 2 provides a simple example of how to place a waypoint. ➤ To place a waypoint at the cursor position or at the vessel position: PLACE WPT AT CURSOR PLACE WPT AT VESSEL 2. Press either the PLACE WPT AT CURSOR or the PLACE WPT AT VESSEL soft key.
46 HSB Series Chartplotter MAKE NEW WAYPOINT 2. Press the MAKE NEW WAYPOINT softkey. The waypoint is placed at the current vessel position, or if not available, the cursor position. It is added to the Waypoint List and named with the next available number. To return to the default softkey display, press ENTER twice. Selecting a Waypoint Selecting a Waypoint Positioning the cursor over a waypoint selects that waypoint and accesses the waypoint soft keys.
47 Chapter 3: Waypoints, Routes and Tracks Waypoint Data Display Waypoint data can be viewed in two ways: you can use the contextsensitive cursor to select the waypoint and thus display the waypoint data box, or you can view waypoint details on the waypoint list. Note: To permanently display the target waypoint data box, select it in the System Set Up menu (see Chapter 5) and use the SCREEN soft key to switch data boxes on. Move the cursor over the waypoint.
48 HSB Series Chartplotter 3. To edit the symbol, press the SYMBOL soft key. Use the soft keys, shown in the following illustration, to highlight the required symbol , then press ENTER. SELECT SYMBOL D4178-1 4. To edit the waypoint name, press the NAME soft key. Erasing a Waypoint The NAME WAYPOINT window is displayed. Use the trackpad to enter or edit the name: Use the left or right side of the trackpad to move the cursor to the character you wish to change.
Chapter 3: Waypoints, Routes and Tracks 49 ➤ To delete a waypoint using the cursor: ERASE WAYPOINT 1. Move the cursor over the waypoint, until the letters WPT are displayed. The waypoint soft keys are displayed. 2. Press the ERASE WAYPOINT soft key. The waypoint is removed from the screen and the Waypoint List is updated. 3. Press ENTER twice to update and remove the waypoint list. To return to the default soft key display, press ENTER. ➤ To delete a waypoint using the waypoint list: ERASE WAYPOINT 1.
50 HSB Series Chartplotter 3.3 Working with Routes A route is made up of a series of waypoints (maximum 50). To make a route you place a series of waypoints on the chart. Working with Routes When a route is created it becomes the current route and is displayed on-screen. The current route is maintained when you power-off. Only one route can be current and is displayed (if it is in the field-of-view) as solid lines connecting waypoints.
51 Chapter 3: Waypoints, Routes and Tracks • Creating a new route. • Saving the current route in the database list. • Clearing the current route. • Retrieving a route from the database list as the current route. • Displaying route information, including the route leg data and waypoint details. Use the waypoint details to review your passage plans for different speeds. • Using the database list to erase and name existing routes. • Editing a route by adding, removing and moving waypoints.
52 PLACE WAYPOINT HSB Series Chartplotter 3. Move the cursor to the position on the chart where you want your first waypoint to be. Press the PLACE WAYPOINT softkey. Note: You can position the cursor on an existing waypoint, if required – the text WPT indicates you are re-using the waypoint rather than placing a new one. This waypoint is included in the route when you press PLACE WAYPOINT. The waypoint appears on the screen at the cursor position.
53 Chapter 3: Waypoints, Routes and Tracks Saving the Current Route You can save up to 20 named routes in the route database list. These routes can then be re-displayed and followed at a later date. Note: If the current route has not been saved, when you attempt an operation that affects this route, e.g. CLEAR ROUTE, you are prompted to save it. ➤ To save and name the current route: SAVE ROUTE 2. Press the SAVE ROUTE soft key. The Route List pop-up and the NAME ROUTE soft keys are displayed. 3.
54 HSB Series Chartplotter If you wish to name the route press the YES soft key. Use the trackpad to move the cursor right or left to the character you wish to edit. Then use the top or bottom of the trackpad to increase or decrease the letter or number. 5. Press ENTER to finish and clear the Name List, then to return to the default soft key display, press ENTER again. Clearing the Current Route Clearing the Current Route & Retrieving a Route You can clear the current route from the screen.
55 Chapter 3: Waypoints, Routes and Tracks ROUTE LIST CURRENT EMPTY 2 EMPTY 3 EMPTY 4 EMPTY ERASE ROUTE ROUTE INFO NAME ROUTE D4263-1 SHOW ROUTE 2. Use the trackpad to select the required route then press the SHOW soft key. The route list is removed and the selected route is shown on screen as the current route. Displaying Route Information You can display the following information that relates to your route: • Route leg or waypoint information, using the context-sensitive cursor.
56 HSB Series Chartplotter Using Route Information to Review Your Passage Plan You can view data for all the waypoints in the current route, or any saved route.
57 Chapter 3: Waypoints, Routes and Tracks INFO FOR ROUTE-CURRENT ROUTE WPT POSITION BRG DISTANCE TOTAL TIME °T 01 50°21^97N --- nm nm ETA 0.0 0.0 --:-- 4.4 4.4 --:-- 5.5 10.0 --:-- 001°15^80W 02 50°21^97N 090 001°08^75W 03 50°27^48N 000 Using the Route List 001°08^75W TIME ETA TOTAL ACTUAL SOG 1.0kn PLANNED SOG 0.0kn D4264-1 4. Press ENTER or CLEAR to clear the Route Information window, then ENTER or CLEAR to return to the route soft keys.
58 HSB Series Chartplotter NAME ROUTE 3. If you NAME a route, use the trackpad to move the cursor right or left to the character you wish to edit. Then use the top or bottom of the trackpad to increase or decrease the letter or number. 4. Press ENTER to clear the Name List, then to return to the default soft key display, press ENTER again.
Chapter 3: Waypoints, Routes and Tracks 59 Adding Waypoints at the End of the Route ➤ To add waypoints at the end of the route: PLACE WAYPOINT UNDO WAYPOINT ACCEPT ROUTE 2. Move the cursor to the required location, and press PLACE WAYPOINT soft key. If you place the waypoint in the wrong position, press the UNDO WAYPOINT softkey. Note: You can UNDO waypoints in the original route, not just the new ones. 3. Place as many waypoints as required, and press the ACCEPT soft key, then press ENTER to finish.
60 HSB Series Chartplotter 3.4 Following Routes and Going to Points The default soft key GOTO accesses the functions to FOLLOW a route and GOTO a waypoint or cursor. When you select the target destination, the chartplotter calculates bearing, distance and cross track error; this information is passed to a helmsman or autopilot. You can also restart the cross track error (XTE) from the actual vessel position to set XTE to zero at that point.
61 Chapter 3: Waypoints, Routes and Tracks Follow a Route Note: The current route may have been created on this display, or created on another unit and received on this display via SeaTalk. ➤ To follow the current route: GOTO 1. Press the GOTO default soft key. The Goto/Follow soft keys are displayed. Alternatively, place the cursor over a route leg until the letters RTE and the route soft keys are displayed. FOLLOW ROUTE 2. Press the FOLLOW ROUTE soft key.
62 HSB Series Chartplotter Target Point Arrival You can set up target alarms (see Chapter 4) to alert you when the vessel is approaching the target point. The arrival alarm is defined as a circle (not visible on the screen), with a specified radius around the target. The alarm is triggered when either of the following conditions is met: • The distance to the target point is less than that specified for the Arrival alarm.
63 Chapter 3: Waypoints, Routes and Tracks Advancing to a Waypoint ➤ Once you are following a route, you can advance to the next waypoint, even if you have not reached the current target waypoint: 1. If necessary, press the GOTO default soft key to display the Goto/ Follow soft keys. GOTO STOP FOLLOW GOTO CURSOR RESTART XTE WAYPOINT ADVANCE D4172-1 2. Press the WAYPOINT ADVANCE soft key. The current leg of the route is abandoned and the the next waypoint becomes the target.
64 HSB Series Chartplotter GOTO WAYPOINT 2. Press the GOTO WAYPOINT soft key. Navigation to the selected waypoint begins. The soft key STOP GOTO is displayed. 3. To return to the default soft key display, move the cursor away from the waypoint. ➤ To navigate directly to the cursor position: 1. Use the trackpad to position the cursor as required. GOTO GOTO CURSOR 2. Press the GOTO default soft key, followed by GOTO CURSOR. If navigation is currently in progress you are warned “Already following route.
Chapter 3: Waypoints, Routes and Tracks 65 3.5 Transferring Waypoints and Routes Displayed Seatalk Waypoints In an integrated system, when a route is made current on any Seatalk equipment it is sent to all SeaTalk instruments, including this chartplotter; this route will override any other current route.
66 RECEIVE WPTS FROM ST/NMEA HSB Series Chartplotter 2. Press the soft key RECEIVE WPTS FROM ST/NMEA. When waypoints are transmitted by other equipment they are added to the open waypoint list on the chartplotter. Routes transmitted on NMEA are appended to the route list. 3. To disable waypoint transfer, press the soft key STOP RECEIVING WAYPOINTS. Alternatively, press ENTER, or CLEAR, twice to close the Waypoint List.
67 Chapter 3: Waypoints, Routes and Tracks 3.6 Using Tracks The Track function is used to mark on-screen the trail that your vessel has followed, as if it had left a visible fixed wake. While the track is turned on, it is recorded in the display unit’s memory. You specify the interval at which track points are made, a line is drawn on-screen between each point. Up to 5000 track points can be saved in total, in up to 5 track files (each a maximum of 1000 points).
68 HSB Series Chartplotter Setting Up a Track You use the track soft keys to switch the track on and to specify the interval at which track points are saved. The interval default is a distance of 0.1nm. The maximum track length is 1000 points, when the track has reached this length, the first points are overwritten. The track is saved until you switch it off. ➤ To set up a track: TRACK INTERVAL Setting Up a Track & Clearing the Current Track 1. Press the TRACK INTERVAL soft key.
69 Chapter 3: Waypoints, Routes and Tracks Managing Tracks Although it is easy to set up a track, and this track is retained even if you turn off your display, you can store a number of different tracks so that you can review them at a later date. This section explains how to perform the following tasks: • Saving and naming a track. • Naming, Erasing and Showing an existing track. Saving and Naming a Track ➤ To save and name the current track: TRACK LIST 1. Press the TRACK LIST soft key.
70 HSB Series Chartplotter Naming, Erasing and Showing a Track ➤ To name an existing track, erase a track or show a track, you select the track from the track list, then press the appropriate soft key as follows: TRACK LIST 1. Press the TRACK LIST soft key. The Track List is displayed. The grey selection bar indicates the selected track. Select the required track then press the appropriate soft key. 2.
71 Chapter 4: Further Chart Operations Chapter 4: Further Chart Operations 4.1 Introduction This chapter explains how to use the additional functions that are provided on the HSB series chartplotter and combined radar/ chartplotter.
72 HSB Series Chartplotter 4.2 Measuring Distances Using the VRM/EBL Key You can obtain an accurate measurement of the distance and bearing between two points by using the VRM/EBL key. ➤ To place a ruler line and Ruler data box: 1. Position the cursor on the starting point from which you wish to measure. 2. Press VRM/EBL. A Ruler data box is displayed showing the bearing and distance from the starting point to the cursor position. The values will be zero until you move the cursor.
Chapter 4: Further Chart Operations 73 4. Press ENTER to fix the end point of the ruler line, and return to normal cursor control. The letter “B” marks the location of the end point on the chart. ➤ To re-position one end of the ruler line: 1. Move the cursor over the ruler line towards the end that you want to re-position, until the letters A-B are displayed. 2. Press ENTER to take cursor control of the ruler. The ruler end moves to the cursor which changes to a four-headed arrow. 3.
74 HSB Series Chartplotter 4.3 Alarms and Timers Alarm Reporting The chartplotter reports the following alarms, that are set using the ALARMS key: Alarms & Timers Alarm Indicates: Arrival Your vessel has arrived at the active waypoint: it has either reached the arrival circle (the radius of which is specified) or, has reached its closest point of approach (defined by a line passing through the waypoint and perpendicular to the route leg).
75 Chapter 4: Further Chart Operations Setting Alarms and Timers ➤ To set up an alarm or timer: 1. Press the ALARMS key. The Alarms Set Up list is displayed, showing the current settings. ARRIVAL ALARM 0.01nm OFF TRACK ALARM ON ANCHOR ALARM OFF COUNTDOWN TIMER 00:33:00 ALARM CLOCK OFF SELECT ARRIVAL ALARM RADIUS D4265-1 2. Use the trackpad to move the selection bar up or down the list.
76 HSB Series Chartplotter 4.4 Man Overboard (MOB) If you lose a person or object overboard, and need to return to the location, you should use the Man Overboard (MOB) function. You can select the type of data used for the MOB position using the set up menus (see Chapter 5).
Chapter 4: Further Chart Operations 77 4.5 Cursor Echo In a combined radar/chart display, or in a system with a radar display connected via Seatalk, you can set the display to enable cursor echo. Cursor echo (accessed from System Set Up, described in Chapter 5) enables you to display a radar cursor on the chart picture, or a chart cursor on the radar picture (you cannot display a remote chart cursor in a chart window).
78 HSB Series Chartplotter NAVIGATION STATUS SAT 03 31 21 23 22 19 17 27 16 15 RESTART GPS SIGNAL STATUS IN USE IN USE IN USE IN USE IN USE IN USE IN USE STATUS STATUS STATUS AZ 085 292 127 075 174 290 056 321 024 237 HDOP FIX STATUS 1 FIX ELEV 085 051 048 043 028 014 012 011 005 065 D-GPS SETUP! D4281-1 GPS Setup ➤ To tune a differential GPS to another beacon: D-GPS SETUP! 1. Press D-GPS SETUP, the Differential GPS Setup pop-up is displayed with MODE and BEACON SELECT soft keys. 2.
Chapter 4: Further Chart Operations 79 4.7 Data Log Mode You can set the chartplotter to log course data every thirty minutes. Up to 48 log entries are held, when 48 entries have been made, the chartplotter will start overwriting the first entries. You start the log using soft keys provided in Data Log Mode. When you select Data Log Mode the log is displayed full-screen. If the screen is full, you use the trackpad to scroll the list and view further log entries.
80 HSB Series Chartplotter TIME 15:30 16:00 16:30 17:00 17:30 18:00 18:30 19:00 19:30 POSITION 50°21^890N 001°20^610W 50°18^010N 001°20^070W 50°21^850N 001°19^290W 50°18^500N 001°21^300W 50°20^990N 001°18^280W 50°19^660N 001°21^960W 50°19^730N 001°18^030W 50°20^930N 001°21^750W 50°18^550N 001°18^650W Data Log Mode STOP LOG CMG DMG 346°M 6.86KM 180°M 7.23KM 012°M 7.23KM 206°M 6.67KM 043°M 5.74KM 245°M 5.00KM 093°M 4.63KM 302°M 5.00KM 145°M 5.
Chapter 5: Setting Up the Chartplotter 81 Chapter 5: Setting Up the Chartplotter 5.1 Introduction Once you have installed your system and are familiar with its basic operation, you may wish to set it up to operate according to your requirements, and display information according to your preferences. This is achieved using the soft key controls that are displayed when you press the MENU key. In most cases, you will only need to use the MENU key options when you first set up your system.
82 HSB Series Chartplotter 5.2 Changing the Set Up Parameters The set up parameters are divided into two sections: • System, controlling the aspects of the system that are not specific to the chartplotter • Chart, controlling the chartplotter, including waypoint information, vectors and radar/chart synchronisation. This section provides instructions for displaying and changing the default values.
Chapter 5: Setting Up the Chartplotter 83 6. Press ENTER, MENU or CLEAR to clear the soft keys and return to the normal display. You can return all the settings to their original factory settings, if required, by performing a factory reset as described in Chapter 7. 5.3 System Parameters The following table lists the System menus and their options, shows the factory default setting, and provides a space for you to make a note of your new default setting.
84 HSB Series Chartplotter Menu Options Factory Default MOB DATA DR POSITION DR MENU TIMEOUT PERIOD NO TIMEOUT 10, 20, 30 SECONDS NO TIMEOUT DISTANCE UNITS NAUTICAL MILES STATUTE MILES KILOMETRES KILOYARDS NAUTICAL MILES SPEED UNITS KNOTS MILES PER HOUR KILOMETRES PER HOUR KNOTS DEPTH UNITS METRES FEET FATHOMS METRES New Default TEMPERATURE UNITS CENTIGRADE FAHRENHEIT CENTIGRADE VARIATION SOURCE AUTO AUTO MANUAL (value) System Parameters CURSOR ECHO LOCAL CURSOR OFF or ON REMOTE C
Chapter 5: Setting Up the Chartplotter 85 Data Boxes Press the SELECT BOXES soft key to display the data box sub-menu. This allows you to select up to 6 data boxes that you wish to be able to display on the chart screeen. Note: A fixed set of 9 of these data items are available for display in the Nav Data window. Data boxes provide regularly used data in a compact form so that most of the chart can still be seen.
86 HSB Series Chartplotter Day/Night This option allows you to change the chart presentation between “day” and “night” modes. In the normal day presentation, black objects are displayed on a white background. If you select NIGHT presentation, the picture is reversed, so that white objects are shown on a black background to reduce the intensity of the image. Help When Help is set to ON, a prompt appears when selecting a soft key or menu choice, and when using the context-sensitive cursor.
Chapter 5: Setting Up the Chartplotter 87 This setting does not affect the default soft key labels, which are controlled by the Soft Keys option previously described. Units You can set the units for distance, speed, depth and temperature. The units you set will be used to display all data, including information received from other instruments on the system. However, the distance units do not affect the chart scale, which is always in nautical miles.
88 HSB Series Chartplotter Manual Mode If you select Manual mode, by pressing either of the MANUAL keys, you can specify the local variation value according to the area in which you are operating. Press the appropriate MANUAL key to adjust the variation up or down, to a maximum of 30° East or West. This value is then transmitted to any other SeaTalk instruments on your system. It is retained if you turn the display off and on again. In Manual mode, incoming NMEA variation is ignored.
Chapter 5: Setting Up the Chartplotter 89 Language Select the language in which you wish information to be displayed. The selected language will be used for screen text, labels, menus and options, but will not affect the letters displayed by the context-sensitive cursor. The language setting also affects the display format for lat/long position information. Chart text, provided by the chart card, is not affected.
90 HSB Series Chartplotter 5.4 Chart Set Up Parameters The CHART SET UP option allows you to set up the chartplotter according to your system configuration and your personal preferences. The following table lists the Chart Set up parameters and their options, shows the factory default setting, and provides a space for you to make a note of your new default setting. Each parameter is described in the following subsections.
Chapter 5: Setting Up the Chartplotter 91 Customise Chart This provides a list of chart options, enabling you to specify how the chart features are displayed. Most options can be toggled between on, off and custom - custom passes on/off control to the SCREEN soft keys (see Customising the Screen Presentation Options in Chapter 2).
92 HSB Series Chartplotter Object Information You can set Object Information ON or OFF. When set ON, object information is displayed in normal chartplotter operation when the cursor is placed over a chart object for two seconds. When set OFF, no information is displayed. Waypoint Options Waypoint controls whether or not the waypoints are shown on the Chart display, with their appropriate symbols. The active waypoint, and waypoints in the current route are always shown.
Chapter 6: Installation 93 Chapter 6: Installation 6.1 Introduction This chapter provides instructions to assist you in planning the installation of the HSB Series Chartplotter aboard your vessel, whether you are installing a simple system such as that shown below, or an integrated system such as those shown in Section 6.5 Integrated Systems. Note: This chapter provides information on installing an HSB Series display unit.
94 HSB Series Chartplotter EMC Installation Guidelines All Raytheon equipment and accessories are designed to the best industry standards for use in the leisure marine environment. Their design and manufacture conforms to the appropriate Electromagnetic Compatibility (EMC) standards, but correct installation is required to maintain EMC performance and CE compliance.
Chapter 6: Installation 95 If your Raytheon equipment is going to be connected to other equipment using a cable not supplied by Raytheon, a suppression ferrite MUST always be fitted to the cable close to the Raytheon unit. Planning the Installation Before you install your system, you should spend some time planning the installation, giving consideration to: • Location – Siting the display unit for ease of use – Providing access for servicing the equipment Section 6.
96 HSB Series Chartplotter 6.2 Unpacking and Inspecting the Components Unpack your HSB Series Chartplotter carefully, to prevent damage to the equipment. It is good practice to save the carton and packing for future use, in case you need to return any units for service. Check that you have all the correct system components. These depend on your system package, as follows: Item Part No.
Chapter 6: Installation 97 6.3 Location This section provides information that affects the possible locations of the display unit, and its position relative to the power supply. Selecting the Display Unit Site The display unit can be mounted using the trunnion (yoke) bracket already fitted, or console mounted using the optional flush-mounting kit. The dimensions of the display unit, including the bracket, are shown in the following diagram.
98 HSB Series Chartplotter When planning the installation of your display unit, the following points should be considered to ensure reliable and trouble free operation: • Convenience: The display unit should be installed in a convenient position, where it can be viewed straight on or with a viewing angle of less than 35°. You may wish to apply power before you install the display unit, to determine the best viewing angle prior to fixing.
Chapter 6: Installation 99 6.4 Integrated Systems The HSB series displays can be linked via the HSB network to transfer chart and radar data between units; this enables a second, repeater display to be used to view and control the chart or radar. The display unit can also receive external signals to drive various features, such as the North Up mode and waypoint display. These signals can be received from equipment such as navaids, fluxgate (compass) sensors, and SeaTalk data networks.
100 HSB Series Chartplotter you only need to connect NMEA In to the master display, which will pass the data to the repeater via SeaTalk. Note: To transfer NMEA data, the display must be powered ON. The following paragraphs describe these data standards and define the data that is transferred. The diagrams on the following pages show examples of integrated systems: the first includes SeaTalk instruments and an HSB repeater display; the second example shows NMEA instruments and an HSB repeater display.
Chapter 6: Installation 101 SeaTalk The SeaTalk standard was originally developed by Autohelm (part of the Raytheon group), and allows compatible instruments to be connected by a single cable carrying power and data in/out. This means that additional instruments and functions can be added to a SeaTalk system, simply by plugging them into the network. SeaTalk is a precise, high-speed, bi-directional protocol which is flexible enough to adapt to any number of instrument heads, without a central processor.
102 HSB Series Chartplotter NMEA The NMEA 0183 Data Interface Standard was developed by the National Marine Electronics Association of America. It is an international standard that enables equipment from many different manufacturers to be connected together and to share information. The information is passed in “sentences”, each of which has a threeletter sentence identifier.
Chapter 6: Installation 103 The NMEA 0183 standard carries similar information to SeaTalk. However, it has the important difference that one cable will only carry information in one direction. For this reason NMEA 0183 is generally used to connect a data receiver and a transmitter together: for example, a compass sensor transmitting heading to a radar, or a GPS sensor (or Chart Plotter) transmitting position and navigation data to a radar.
104 HSB Series Chartplotter * If Magnetic Heading is not available, the True Heading and Variation (if available) are used to generate the magnetic heading.
Chapter 6: Installation 105 6.5 Cable Runs You need to consider the following before installing the system cables: – You need to fit the power cable. Additional cables will be required if you are installing an integrated system. – All cables should be adequately cleated and protected from physical damage and exposure to heat - avoid running cables through bilges or doorways, or close to moving or hot objects.
106 HSB Series Chartplotter power source and the connector block, and then select the wire size indicated by the distance following table. Maximum Extension Power Cable Lengths (m), 12V Systems Inter-Unit Cable(s) mm2: 1.5 AWG: 16 Maximum extension 11.0 Power Cable Core 2.0 2.5 4.0 15 14 12 6.0 10 10.0 8 15.0 45.0 70.0 20.0 30.0 6.
Chapter 6: Installation 107 Console Mounting The display unit can be console mounted if required, using the optional flush-mounting kit (M92708). CAUTION: Make sure there are no hidden electrical wires or other items behind the location before proceeding. Make sure there is sufficient rear access for mounting and cabling. 1. Check the selected location for the unit. A clear, flat area at least 230mm (9in) wide by 210mm (8¼in) high, with at least 152mm (6in) of clearance behind the panel, is required. 2.
108 HSB Series Chartplotter 6.8 HSB Series System Connections Grounding the Chartplotter It is important that an effective RF ground is connected to the chartplotter. You must ground the system by connecting the drain wire (screen) of the Power/NMEA Input cable to the nearest ground point of the ship’s RF ground system. If you need to extend the wire, the extension wire should be an 8mm braid or 6.0mm2 (AWG 10) multi-stranded cable.
Chapter 6: Installation 109 • SeaTalk compatible (for example, compass, GPS and instruments), and there is no existing SeaTalk bus • NMEA compatible, but operate only from 12V (for example, compass, GPS and some navigators) The DC~DC converter must conform to the following specification: Input 21 to 32 V DC Output 13.
110 HSB Series Chartplotter HSB Connection You can connect any two HSB displays, using an HSB cable connected between their HSB connectors on the rear of each display unit. Note: The HSB cables are fitted with ferrite clamps at each end to ensure EMC conformance. SeaTalk Connection The SeaTalk input/output should be connected at the rear SeaTalk 3-pin connector. This appears as follows, when viewed from outside: SeaTalk In/Out 1. Red (No internal connection) 2. Screen (0V) 3.
Chapter 6: Installation 111 To connect the display unit to the SeaTalk bus, connect a standard SeaTalk cable between the SeaTalk connector on the rear of the display and a SeaTalk instrument or the SeaTalk bus. Standard SeaTalk cables are available in a range of lengths (part numbers W284 to W287), and cables for connecting to older SeaTalk units are also available (part numbers D187 or D188).
112 HSB Series Chartplotter Note: The power cable is fitted with a ferrite clamp to ensure EMC conformance. Power Connection The RED wire must be connected to the feed from the positive (+) battery terminal and the BLACK wire to the feed from the negative (–) battery terminal. The shielded wire should be connected to the ship’s RF ground as previously described in Grounding the Chartplotter. Any unused cores should be insulated and taped back.
Chapter 6: Installation 113 Using the SeaTalk Auxiliary Junction Box to Connect a SeaTalk GPS A junction box (provided with the RL70RC, optional with the RL70) is used to connect the SeaTalk GPS system (or any other SeaTalk instrument) to the HSB Series display unit. This junction box enables the SeaTalk bus, power and GPS to be connected. If power is not already available (via another SeaTalk instrument), the junction box can be used to apply power to the Seatalk bus for other applications.
114 HSB Series Chartplotter 6.8 System Check and Initial Switch On Once you have installed your Chartplotter and made all the connections, you need to check your installation before using the system for navigation. If you encounter any problems, refer to Chapter 7. You may wish to read Chapters 2, 3 and 4, and familiarise yourself with the operation of the Chartplotter, before performing the initial set up.
Chapter 6: Installation 115 SYSTEM SET UP MENU DATA BOXES BEARING MODE CURSOR REFERENCE CURSOR READOUT DAY/NIGHT HELP SOFT KEYS KEY BEEP MOB DATA MENU TIMEOUT PERIOD DISTANCE UNITS SPEED UNITS DEPTH UNITS TEMPERATURE UNITS VARIATION SOURCE CURSOR ECHO DATE FORMAT TIME FORMAT TIME OFFSET LANGUAGE HSB STATUS SIMULATOR TRUE RELATIVE RNG/BRG RNG/BRG ON ON ON DR NO TIMEOUT NAUTICAL MILES KNOTS METRES CENTIGRADE AUTOMATIC DD/MM/YY 24 HOUR UTC ENGLISH (UK) NOT CONNECTED OFF D3650-2 3.
116 HSB Series Chartplotter
Chapter 7: Maintenance and Problem Solving 117 Chapter 7: Maintenance and Problem Solving This chapter provides information on routine maintenance and on possible causes of problems you may experience with your HSB Series Chartplotter. 7.1 Maintenance Warnings The chartplotter display unit contains high voltage.
118 HSB Series Chartplotter 7.2 Resetting the System There are three types of reset available for the HSB Series Chartplotter: • Factory Reset: This resets all values back to their original factory settings. CAUTION: The factory reset clears the Waypoint and Route databases. • Power-On Reset: When you turn the display off and on again, the screen reverts to the chart picture with all windows cleared.
119 Chapter 7: Maintenance and Problem Solving 7.3 Problem Solving Prior to packing and shipping, all Raytheon products are subjected to comprehensive test and quality assurance programmes. However, if this unit should develop a fault, please refer to the following table to identify the most likely cause and the corrective action required to restore normal operation.
120 HSB Series Chartplotter first contact the Technical Support Department at 1-800-539-5539 ext. 2065 to verify your requirements. For Technical Support: For technical support, call 1-800-539-5539 extension 2444 or (603) 6477530 extension 2444. The Raytheon Fax number is 1-603-634-4756. Our Technical Support Specialists are available to answer questions about installing, operating and trouble-shooting all Raytheon products.
Chapter 7: Maintenance and Problem Solving 121 How to Contact Raytheon Marine in Europe In Europe, Raytheon support, service and accessories may be obtained from you authorised dealer, or contact: Raytheon Marine Company Anchorage Park, Portsmouth PO3 5TD, England Tel (01705) 693611 Fax (01705) 694642 Our technical support staff may also be reached via the Internet. Questions may be addressed directly to: techsupra@raytheon.com. Or visit the Raytheon Electronics World Wide Web site: www.raymarine.
122 HSB Series Chartplotter
Appendix A: Specification 123 Appendix A: Specification HSB Series 7” LCD Displays General Approvals CE - conforms to FCC - conforms to 89/336/EEC (EMC). EN 60945:1997 Part 80 (47CFR) and Part 2 (47CFR) Size 222 x 204 x 75 mm (8.8” x 8” x 3”), excluding bracket Weight 1.2Kg (2.6lbs) Mounting Trunnion with panel mount option Power External 10.
124 HSB Series Chartplotter Screen Functions Full, half and quarter screens available dependant on function Data Boxes Up to six user selectable information boxes Chartplotter Features Cartography C-MAP® NT micro cartridges available from C-MAP® Chart of the world built in Display Windows Chart, data, BDI, CDI, Navdata Chart Scaling 1/64nm (if cartographic data is available) to 4000nm Presentation Modes Course up North up (selectable True or Magnetic) Head up or Waypoints 1000 waypoints enter
Abbreviations 125 Abbreviations A Amp ANSI American National Standards Institute AWG American Wire Gauge BDI Bearing Deviation Indicator Brg Bearing CDI Course Deviation Indicator CFR Code of Federal Regulations COG Course Over Ground CTR Centre db deciBels DC Direct Current DR Dead Reckoning EBL Electronic Bearing Line EMC Electro Magnetic Compatability FCC Federal Communication Commission FLT Float - floating EBL/VRM ft feet FTC Fast Time Constant GPS, dGPS Global Po
126 HSB Series Chartplotter Kg kilogram kW kilo Watt lat latitude lbs pounds LCD Liquid Crystal Display lon longitude M Magnetic m metres MBS Main Bang Suppression mm millimetre MOB Man OverBoard MRK Mark nm nauticl mile NMEA National Marine Electronics Association POS Position (of vessel) RF Radio Frequency Rng Range rpm Revolutions Per Minute SHM Ships Heading Marker SOG Speed Over Ground T True TTG Time To Go V Volts VMG Velocity Made Good VRM Variable R
Index 127 Index A Add a Waypoint to a Route 59 Advance to a Waypoint 63 Alarm Clock Alarm 74 ALARMS Alarm Clock 74 Dedicated Key 74, 75 Alarms Anchor 74 Arrival 62, 74 Countdown Timer 74 External 74 Handling 74 MOB 76 Off Track 74 Setting 75 Alter the Current Route 62 Anchor Alarm 74 Arrival Alarm 62, 74 B BDI Window Options 6 Bearing Mode 83, 85 C Cable Runs 95, 105 Cables Power 105 CDI Window Options 6 Centre the Chart 7 Centre the Vessel 26 Chart Centre 24 Data 17 Displaying 18 Scale 17, 24, 26, 51.
HSB Series Chartplotter 128 Create a Route 51 Cross Track Error.
Index 129 Installation Guidelines 94 Servicing and Safety Guidelines 117 Erase Route 57 Track 70 Waypoint 48 External Alarms 74 F Factory Reset 118 Features Display 4 Find Ship 25 Follow a Route 60, 61 Stop 64 Functions Display 4 Identifying a Radar Target on the Chart Display Sc 40 Inserting a Waypoint in a Route 58 Chart Card 17 Installation 93–115 Cable Runs 95 EMC Guidelines 94 Integrated Systems 95 Location 95 Planning 95 Integrated System 3, 50 Definition 2 Installation Considerations 95, 99 Power
HSB Series Chartplotter 130 Marks - Radar 44 MARKS Key 45, 46, 65, 76 Master Definition 2 Display 3, 17, 100 Measuring Distances Using the VRM/EBL Key 72 MENU Key 67, 81, 82 Menu Timeout 84, 86 MOB 76. See also Man Overboard Alarm 76 MOB Data 84, 86 Mounting Display Unit 106 Console 107 Trunnion 106 Moving a Data Box 30 a Waypoint 49 Around the Chart 24, 51 MULTI Key 15 N Name a Route 53, 57 a Track 69, 70 a Waypoint 48 Nav Data Window Options 6 Navigation. See Follow Route.
Index Resetting the System 118 Restart XTE 60, 63 Retrieve Route 54 Reverse Route 59 Review Your Passage Plan Scenario 38 Route Altering 62 Clearing 54 Creating 51 Current 50 Database List 49, 53, 54, 56, 57 Editing 58. See also Route: Altering Erasing 57 Follow 60, 61 Information 56 Joining 62 List.
HSB Series Chartplotter 132 Setting 75 Track List.
Limited Warranty Certificate Raytheon Marine Company warrants each new Light Marine/Dealer Distributor Product to be of good materials and workmanship, and will repair or exchange any parts proven to be defective in material and workmanship under normal use for a period of 2 years/24 months from date of sale to end user, except as provided below. Defects will be corrected by Raytheon Marine Company or an authorized Raytheon dealer.
United States of America Raytheon Marine Company 676 Island Pond Road Manchester, NH 03109-5420 U.S.A. Tel Fax UK, Europe, Middle East, Far East Raytheon Marine Company Tel Anchorage Park, Portsmouth Fax PO3 5TD, England Fax 603-647-7530 603-634-4756 (44) 1705 693611 (44) 1705 694642 Customer support (44) 1705 661228 Factory Service Center United States of America Raytheon Marine Company 676 Island Pond Road Manchester, NH 03109-5420 U.S.A.
NO POSTAGE NECESSARY IF MAILED IN THE UNITED STATES BUSINESS REPLY MAIL FIRST CLASS MAIL PERMIT NO. 369 MANCHESTER NH POSTAGE WILL BE PAID BY ADDRESSEE Attn: Warranty Department Raytheon Marine Company 676 Island Pond Road Manchester NH 03109-9953 USA Note: This information is held by Raytheon Marine only and shall not be made available to any other companies. Raytheon Marine may send you mailshots/details of any new products.
North and South America Detach and mail this portion within 48 hours. To validate the warranty, the customer or dealer must fill in the requested information below and mail to address shown on front. Stick barcode label here Retain other portion for your records. Purchased from Purchase date Dealer address Installed by Installation date Commissioned by Commissioning date Owner’s name Boat’s name Mailing address UK, Europe, Middle East and Far East Detach and mail this portion within 48 hours.
