C-Series Display Reference Manual Document number: 81221_4 Date: March 2006
E-Series Reference Manual Trademarks and registered trademarks Autohelm, HSB, Raymarine, RayTech Navigator, Sail Pilot, SeaTalk and Sportpilot are registered trademarks of Raymarine Limited. Apelco is a registered trademark of Raymarine Holdings Limited (registered in all major marketing territories).
Important information i Important Information Intended use The display units detailed in this handbook may form part of marine navigational radar system or GPS system intended for use on (non-IMO/SOLAS class) leisure vessels or small workboats. This handbook contains important information on the operation and maintenance of your C-Series Display. To get the best results in operation and performance, please take the time to read this handbook thoroughly.
ii C-Series Display Reference Manual WARNING:Fishfinder sounder module Removing the transducer cable from the rear of the fishfinder sounder module whilst it is switched on can cause sparks. Only remove the transducer cable after power has been switched off. Ensure that the sounder module is mounted where it is well ventilated and in an area free from flammable vapors.
Important information iii products manufactured by others, or by errors in chart data or information utilized by the product and supplied by third parties. About this manual This manual describes how to operate your C-Series display in conjunction with Navionics cartography. It assumes that all peripheral equipment to be operated with it is compatible and has been correctly installed.
iv C-Series Display Reference Manual Alternatively, anywhere in North America call Navionics toll-free on 1-800-848-5896 Outside of North America, contact your local dealer or Navionics SpA on: Phone: (+39) 0584 961696 or Fax: (+39) 0584 961309) When archiving data, Raymarine recommends that you only use SanDisk CF memory cards. Other brands of CF memory card may not work in your C-Series Display.
Contents v Contents Chapter 1: Overview ..................................................................................................1 1.1 What will my C-Series integrate with? .................................................................. 1 1.2 What can the C-Series Display do? ........................................................................ 2 1.3 The Simulator ........................................................................................................
vi C-Series Display Reference Manual Chapter 3: Working with Waypoints .....................................................................29 3.1 What is a waypoint? ...........................................................................................29 3.2 How are waypoints represented? .......................................................................30 3.3 Placing a waypoint .............................................................................................31 3.
Contents vii Displaying details of objects and features .....................................................48 Finding nearby features and services ............................................................48 Displaying details of tides .............................................................................49 Displaying details of currents ........................................................................50 Displaying details of port services ................................................
viii C-Series Display Reference Manual Creating a track .............................................................................................79 Creating a route from a track ........................................................................80 4.16 Editing tracks ......................................................................................................81 Selecting a track for editing ...........................................................................
Contents ix 5.8 Setting up your fishfinder ..................................................................................110 Display settings ...........................................................................................111 Transducer Calibration ................................................................................112 DSM Setup ..................................................................................................113 5.
x C-Series Display Reference Manual Acquiring a target to track ..........................................................................147 Cancelling targets .......................................................................................147 Displaying vessel identity (AIS) ...................................................................148 6.11 Setting up your radar ........................................................................................148 6.
Contents xi Chapter 11: Automatic Identification System (AIS) ............................................167 11.1 Introduction ......................................................................................................167 11.2 What is AIS? .....................................................................................................167 Classes of AIS data ......................................................................................167 11.3 What do I need to run AIS? .........
xii C-Series Display Reference Manual Servicing and Safety ....................................................................................193 Routine checks ............................................................................................193 Cleaning the display ....................................................................................194 13.3 Resetting the Display ........................................................................................194 Settings reset .........
Chapter 1: Overview 1 Chapter 1: Overview This chapter gives an overview of the C-Series display system and its features. 1.1 What will my C-Series integrate with? Autopilot Instruments AIS receiver GPS Radar scanner C-Series display PAGE ACTIVE WPTS MOB DATA MENU OUT RANGE IN Remote keyboard OK DSC VHF CANCEL 11.18.
2 C-Series Display Reference Manual 1.2 What can the C-Series Display do? With the appropriate equipment connected to your system and the necessary data available, your C-Series display combines the following applications which are used to: Chart (Chapter 4) North-Up (Relative Motion) Local Locate where you are. Interpret your surroundings. Monitor where you are going. Record where you have been. Navigate to a specified position (waypoint). Build and navigate routes.
Chapter 1: Overview 3 Data (Chapter 7) D7376-1 View data generated by the system or by instruments available on NMEA 0183, NMEA 2000 and SeaTalk or SeaTalk2. Course Deviation Indicator (Chapter 8) 3nm North-Up Relative Motion Local View real-time display of your vessel on a 'rolling road' in 3D perspective. Give details of any correction required to steer your vessel along a given course. D7379-1 View data about the distance and time to go until you reach a specified point.
4 C-Series Display Reference Manual Waypoints (Chapter 3) & AIS (Chapter 11) Whilst not applications in their own right, waypoints and AIS are handled at system level and are covered in separate chapters. 1.3 The Simulator The C-Series Display includes a simulator mode, which allows you to practice operating your display without data from a GPS antenna, radar scanner, fishfinder or AIS receiver. The simulator mode is switched on/off in the System Setup Menu (see page 183).
Chapter 2: General Operation 5 Chapter 2: General Operation 2.1 Introduction This chapter gives details of the general operation of the C-Series display, and covers the following subjects: • Powering the display on/off. • Using the controls. • Application display. • Displaying and editing additional information. • Adjusting the display lighting. • Initial setup procedures. • Using CompactFlash cards. • Managing data. • Emergencies and warnings. 2.
6 C-Series Display Reference Manual 2.3 Using the controls The control panel ACTIVE When multiple windows are open: - Press to select required window. - Press and hold to maximise current window. - Press again to return to multiple windows. PAGE Press to scroll through available pages. Press and hold to select different page set or customise your own layout.
Chapter 2: General Operation 7 Buttons and soft keys To navigate to the required function you will need to press a series of buttons and/or soft keys: PAGE Buttons Access system functions or change what you see on-screen. Within the text of this document they are written in bold capitals e.g. WPTS/MOB. Press and hold to access short cuts. ACTIVE WPTS MOB DATA MENU Soft keys WAYPOINT AT CURSOR ERASE WAYPOINT WAYPOINT AT VESSEL SORT LIST WAYPOINT AT LAT/LONG... SET DEFAULT SYM & GROUP...
8 C-Series Display Reference Manual The cursor When you are using the chart and radar applications, the cursor is used to move around the screen: D7366_3 The cursor appears on the screen as a white cross. WPT D7369-2 D7368_2 If the cursor has not been moved for a short period of time, it changes to a circle with a cross in it, to make it easier to locate on the screen. The cursor is context-sensitive - when it is placed over an object e.g.
Chapter 2: General Operation 9 2.5 Additional screen information Information is displayed on the screen using a variety of methods: Status Statusbar bar Gives Givesinformation informationspecific specifictoto each eachapplication. application. Cannot Cannotbe beedited editedorormoved. moved. 3nm 3nm Head-Up Head-Up Data Data bar bar Gives Gives information information associated associated with with your your boat boat or or the the environment. environment.
10 C-Series Display Reference Manual Menus 0 MENU MENU D6582-1 Menus enable you to configure your system to your particular needs. Whenever the MENU button is pressed, the Setup menu is displayed containing a list of all the menus available for the active application together with system wide menus e.g. Setup Menus for the active application External equipment/ instruments GPS Status... Compass Setup... AIS Layer Status... System-wide menus System Setup... Alarm Setup... Display Setup... Databar Set.
Chapter 2: General Operation 11 Editing the dialog box information Dialog boxes enable data to be edited or entered into a list e.g. Edit Waypoint screen. To edit/enter data into a dialog box: 1. Select the field for editing: e.g. Symbol Name Waypoint 1 EDIT NAME Group My Waypoints Comment D8502-1 Highlight field to be edited e.g. waypoint name 2. Edit/enter data and save: e.g.
12 C-Series Display Reference Manual Status icons The status icons on the data bar confirm whether the appropriate connections to your C-Series system have been made: Status icon Description D6892-3 The boat and fish icon indicates the current status of your fishfinder: Icon animated - connection to a DSM has been successful. Icon static - the DSM is connected but not transmitting. Icon greyed-out - no DSM is connected.
Chapter 2: General Operation 13 2.6 Initial setup procedures When you first use your C-Series Display after it has been commissioned (see Installation Guide), we recommend that you carry out the following: • Set the language, the date and time format and preferred units of measurement. • Select a page set. • Select an application page/window. • Adjust the display lighting. Note: For full details of all setup and customizing options, please refer to Chapter 12:System setup and customizing.
14 C-Series Display Reference Manual Selecting a page set Your Display has four pre-configured page sets and one empty set for you to choose from. PAGE OK Highlight appropriate pre-configured page set D8511-1 Press & hold Note: Alternatively, you can access the Select Page Set screen via MENU.
Chapter 2: General Operation 15 Selecting an application window When the selected page has more than one window, the window that is currently active will be bordered in red e.g. Soft keys associated with active window D8516_1 Active window highlighted Changing the active window To change the active highlight to other windows on the page and display the associated soft keys: e.g.
16 C-Series Display Reference Manual Adjusting the display lighting The display has two distinct color palettes, for day and night operation. You can also manually adjust the backlight level. Note: The display lighting is a local setting and will therefore only affect the individual display on which you are working. Day/night operation To select the day/night mode of operation: PALETTE DAY NIGHT D6802-3 OK Toggle as required The display saves the current palette when the unit is powered off.
Chapter 2: General Operation 17 2.7 Using CompactFlash cards Cautions CAUTION: CompactFlash Card Installation When installing CompactFlash cards ensure that the card is fitted the correct way around. DO NOT try to force the card into position as this may result in irreparable damage to the card. CAUTION: Water Ingress To prevent the ingress of water and consequent damage to the display, ensure that the chart card door is firmly closed at all times. This can be confirmed by an audible click.
18 C-Series Display Reference Manual Inserting a card To insert a card, refer to the illustration and: 1. Check that you are using the correct type of card (see Important Information, at the beginning of this manual). 2. Open the chart card door, located on the front left of the display. 3. Insert the card as shown, with the lip of the card facing inwards. It should position easily. If it does not, DO NOT force it, check the direction in which the lip is facing. 4. Gently press the card home. 5.
Chapter 2: General Operation 19 3. Grip the card and pull to remove it from its slot. 4. To prevent the ingress of water and consequent damage, close the chart card door and press firmly until a click is heard. 5. Press OK. ...with the unit powered down 1. Open the chart card door. 2. Grip the card and pull to remove it from its slot. 3. To prevent the ingress of water and consequent damage, close the chart card door and press firmly until a click is heard. 2.
20 C-Series Display Reference Manual 2. Select list containing data for saving: e.g. ROUTE LIST Toggle to required list Contents for selected list displayed D8655_1 Route 1 Route 2 Route 3 SELECT LIST WPT RTE TRK 3. Define data for saving To save all items in list to card: SAVE ALL Save Route Or To save individual items: e.g. e.g. ROUTE LIST SAVE ROUTE Follow on-screen instructions to remove card Route 1 Route 2 Route 3 D8520_1 Highlight item for saving Retrieving information from a card 1.
Chapter 2: General Operation 21 To retrieve all selected database items: RETRIEVE ALL Retrieve Route Or To retrieve individual items: e.g. Follow on-screen instructions ROUTE LIST RETRIEVE ROUTE Route 1 Route 2 Route 3 D8656_1 Highlight item for retrieving If whilst retrieving information a selection is already found to exist on the system, a warning message will appear.
22 C-Series Display Reference Manual To delete all items: ERASE ALL YES Or To delete individual items: e.g. ROUTE LIST ERASE ROUTE Route 1 Route 2 Route 3 D8657_1 Highlight item for deleting Sending and receiving information using a PC You can transfer and retrieve waypoints or routes to and from another instrument or PC using NMEA. With a RayTech 6.0’s planner you can transfer waypoints and routes via a CF memory card.
Chapter 2: General Operation 23 Password protecting your waypoints If required, you can prevent access to, modification and sight of your waypoint and route databases and functions by means of a password. Password confirmation When Password Protection is enabled and you are attempting to access a password protected function for the first time during a power-cycle, the system will request confirmation of your password before you can: • Access WPTS key functions.
24 C-Series Display Reference Manual 2. Change the Enable Password status to ON, read and accept the warning: Setting Password Protection required a password to access your waypoint and route databases. If you forget your password you will lose your waypoints and routes Raymarine recommends that you archive your waypoints and routes Waypoint Password Setup OK ON Select Enable Password YES Read and accept the warning Select ON. D8962_1 Enable Password Change Password... 3.
Chapter 2: General Operation 25 Setup System Setup Menu Radar Setup... MENU GPS Status... Compass Setup... System Integration Waypoint Password Setup System Setup... Select System Setup Menu Highlight Waypoint Password Setup Select Waypoint Password Setup. D8960_1 Highlight required System Setup Menu 2. Enter your password ensuring that the appropriate upper or lower case characters are used and then enable/disable the password protection, as required.
26 C-Series Display Reference Manual 2.9 Emergencies and warnings You can use your C-Series display to mark the position of a man overboard or to sound an alarm when a particular situation occurs e.g when a depth limit is reached, a specified period of time has elapsed etc. Man Overboard (MOB) Marking a MOB WPTS MOB D6652-3 Press and hold until alarm sounds If you lose a person or object overboard, and need to return to the location, you should use the Man Overboard (MOB) function immediately.
Chapter 2: General Operation 27 Silencing a MOB To temporarily silence the alarm from a MOB, press any key on any instrument on the SeaTalk system. After approximately 10 seconds the alarm will sound once more if the state of MOB is still active. Silencing an alarm will not deactivate or clear the MOB state.
28 C-Series Display Reference Manual
Chapter 3: Working with Waypoints 29 Chapter 3: Working with Waypoints This chapter gives details of how to place, edit, manage and navigate to a waypoint. 3.1 What is a waypoint? A waypoint is a position marked on a chart, radar or fishfinder window to indicate a site (for fishing, diving etc.) or as a place to navigate to. By default, all waypoints are indicated on screen by a waypoint symbol - x. This symbol can however be changed if you wish.
30 C-Series Display Reference Manual 3.2 How are waypoints represented? Waypoints on Chart and Radar windows On chart and radar windows, a waypoint is represented when it is both active (displayed in a box) and inactive (no box) i.e. Default waypoint Active waypoint Alternative symbol D8694_1 Waypoint 1 Waypoints on CDI windows D8930_1 On CDI windows, a waypoint is represented only when it is active (displayed in a box).
Chapter 3: Working with Waypoints 31 3.3 Placing a waypoint A waypoint can be placed at: • The cursor position. • Your vessel’s position. • At a position of your choosing (using lat/lon or Loran TD coordinates between 800 N/S). When you are placing a waypoint, you can either accept the default or customize its details. For more information see page 34. Once a waypoint has been placed, you can view its details and edit them (if necessary). For more information, see page 33 and page 34. ...
32 C-Series Display Reference Manual 3.4 Navigating to a waypoint This section explains how to start and stop navigating to a waypoint. When you navigate to a waypoint or to the cursor position, the data is sent on NMEA 0183 and SeaTalk and can be used by an autopilot, if connected. For more information on navigation, see page 56. Start navigating to a waypoint D8285_1 You can navigate to a waypoint using the cursor, via the WPTS MOB button or by selecting the GOTO option.
Chapter 3: Working with Waypoints 33 Stop navigating to a waypoint If at any time you wish to stop navigating towards the selected waypoint: WPTS/ MOB GOTO WAYPOINT GOTO WAYPOINT WPTS/ STOP GOTO OPTIONS... MOB OPTIONS... STOP GOTO Or Or: WPT WPT Position cursor over active waypoint. D7505-2 Position cursor over active waypoint.
C-Series Display Reference Manual D6560-2 34 To access the waypoint list: REVIEW AND EDIT WAYPOINTS... Waypoint List OK To exit waypoint list Select required waypoint D7507-2 WPTS/ MOB 3.6 Editing a waypoint Once a waypoint has been placed it can be edited in a variety of ways. You can: • Change the waypoint details - name, symbol, group or add a comment. • Move a waypoint. • Erase a waypoint. D6561-2 D6561-1 • Change the default symbol and group of newly placed waypoints.
Chapter 3: Working with Waypoints 35 Changing waypoint details When a waypoint is created it is assigned a default name, symbol and group. You can change these details to suit your needs and add a comment if required. This is particularly useful when you are managing large numbers of waypoints. To change the details of a waypoint: 1.
36 C-Series Display Reference Manual CAUTION: It is possible to move waypoints that are used in routes. In such instances, the stored route will include the Waypoint in its new position. Ensure that this does not present a navigation hazard. Erasing a waypoint(s) You can erase any waypoint on the system (including groups of waypoints) except: • The active waypoint or • Any waypoint used in a route. Notes: (1) If a route is hidden its waypoints can still be displayed.
Chapter 3: Working with Waypoints 37 Erasing all waypoints If you need to erase all your waypoints, you can use the ARCHIVE & TRANSFER soft keys: 1. Select the ERASE FROM SYSTEM and the appropriate list: SELECT LIST WPT ERASE FROM SYSTEM... Select the WPT list D8716-1 ARCHIVE AND TRANSFER DATA 2.
38 C-Series Display Reference Manual Group List Group OK EDIT DEFAULT To save D9055-1 Select required default group Note: To abandon the symbol or group default change, press CANCEL. 3.7 Sorting the waypoint list If your system contains a large number of waypoints, you can sort your waypoint list to make it easier to locate a particular waypoint.
Chapter 3: Working with Waypoints 39 e.g. GROUP LIST WPTS/ MOB REVIEW AND EDIT WAYPOINTS ... WAYPOINT GROUPS ... Deep fishing Shallow fishing D6885-3 Reef fishing You can now make a new waypoint group, or erase, move or rename existing groups. Making a new waypoint group To create a new waypoint group: 1. Display the group list (see above). Make a new group and accept the default name: MAKE NEW MAKE NEW OK OK GROUP... MAKE NEW GROUP... D8293_1 GROUP... D8293_1 2.
40 C-Series Display Reference Manual 4. Determine the group that the waypoint is to be moved to: GROUP LIST MOVE BETWEEN GROUPS My Waypoints Waypoint 1 Waypoint 2 Waypoint 3 GROUP LIST GROUP B Fishing My Waypoints Deep fishing Shallow fishing Reef fishing SELECT GROUP B Move control to Group B OK Select group to add waypoint to D8298_1 GROUP A 5.
Chapter 3: Working with Waypoints 41 Erasing a group You can erase any waypoint group from the system except the group containing the active waypoint. When a waypoint group is erased, the group name together with all of the waypoints in that group are erased from the system with the exception of: • ‘My Waypoints’ - the waypoints contained within this group are deleted but the group name remains. • Waypoints used in routes within your system.
42 C-Series Display Reference Manual Showing/hiding waypoint symbols You can define which waypoint symbol types are shown/hidden in the radar or chart application: 1. Display the SHOW BY SYMBOL option: SHOW BY SYM D8839_1 SHOW/HIDE WAYPOINTS... PRESENTATION... Select SYM 2.
Chapter 4: Using the Chart 43 Chapter 4: Using the Chart 4.1 Important Safety When using your chartplotter you should always check that a route is safe. Zoom in to check for hazards, such as small shoals, that may not be shown on a smaller scale chart. Until you are familiar with interpreting the chart display, you should take every opportunity to compare the displayed objects with visual targets, such as buoys and coastal structures.
44 C-Series Display Reference Manual Chart cards To use your C-Series Display as a navigation aid, charts with the appropriate level of detail for the geographic area you wish to navigate are required. The charts are available in electronic format on Navionics Chart cards. Details of these cards and how to obtain them is given on page iii. When archiving data, Raymarine recommends that you only use SanDisk brand CF memory cards. Other brands of CF memory cards may not work in your C-Series Display. 4.
Chapter 4: Using the Chart 45 4.3 Viewing the chart You will normally view your chart with the vessel on screen and motion mode ‘active’. When motion mode is active, as your vessel moves, the chart is redrawn to keep the vessel on screen. When you zoom the chart in active mode, the chart zooms about your vessel position. Alternatively, you may be planning a journey and do not want the chart to redraw as your vessel moves.
46 C-Series Display Reference Manual 4.5 Where am I on the chart? D6627-1 Boat symbol Your current position is represented on screen by a boat symbol. If neither heading nor COG data is available, the vessel is shown as a solid circle. If positional data has been selected for display (see page 180), your position will be displayed in the data bar under VES POS.
Chapter 4: Using the Chart 47 A feature of the chart is ‘autoscale’. If you select a chart scale that does not have cartographic detail in some areas, the chart will use the most detailed level available for the surrounding area and stretch it to fit the selected scale. This means that you will never have blank or hatched areas on your screen. However there may be some misalignment of objects which cross the chart boundary in this area. To zoom in/out: e.g. 3nm ...
48 C-Series Display Reference Manual Displaying details of objects and features To view details: More detailed information for selected object displayed. Move cursor over object, to display basic information. D 6771-2 OK If the object you have selected has more than one subject area: Highlight the required subject area. Details displayed in right-hand column.
Chapter 4: Using the Chart 49 SELECT PORT FIND NEAREST... WAYPOINTS PORTS PORT SERVICES TIDE STATIONS CURRENT STATIONS WRECKS OBSTRUCTIONS Select required category 16 nearest to cursor in selected category displayed. D8310_1 FIND Once located, you can use the soft keys and trackpad to: • Display detailed data for services at the listed ports. • Show the selected item on the chart. • GOTO the selected waypoint • View tidal/current data for the selected tidal/current station.
50 C-Series Display Reference Manual You can now: • Move the time-selector, using the trackpad/rotary control. • Change the displayed date, using the soft keys. Displaying details of currents You can display details of currents by: • Selecting the appropriate current diamond (see below) or • Via the FIND NEAREST function (see page 48). ... using the current diamond 1.
Chapter 4: Using the Chart 51 ... using the port search option The port search option allows you to specify the name a port and display its services: 1. Select the edit name option: SEARCH BY NAME EDIT NAME D8314_1 OK 2. Enter the port name (or the first few characters of the port name) and search: SEARCH BY NAME SEARCH OK Enter Port Name GA D 8309_1 Enter port name (or part of) using: or Soft key , Note: For help with entering text into a dialog box, please refer to page 11. 3.
52 C-Series Display Reference Manual ... using the port symbol The services available at a particular port can be displayed by selecting its symbol: OBJECT INFO Select appropriate port symbol Position 29058'.147N 093052'.215W General Services Repair Services Fuel Other information Services for selected port displayed D9099_1 OK RAINBOW HARBOR Dredged area Depth area You can now view details of individual services: 1.
Chapter 4: Using the Chart 53 Displaying details of business services & points of interest When a suitable chart card is installed the location of various business services and points of interest are indicated by the following symbols: Business services/points of interest symbols Airport Babysitting Barber Bank Camping Car hire Firemen Fishing equipment Gas/Petrol Parking Golf Gym Hospital Hotel Laundry Nautical repairs Marina Museum Police Post Office Restaurant Ship repairs Shop
54 C-Series Display Reference Manual Displaying vessel identity (AIS) If you have an AIS receiver fitted to your system, you can use the AIS feature to: • Display targets for any other AIS equipped vessels. • Display voyage information being broadcasted by these targets i.e. their position, course, speed and rate of turn. • Display basic or detailed information for each target vessel including safety critical target data. • Set up a safe zone around your boat. • View AIS alarm and safety related messages.
Chapter 4: Using the Chart 55 4.8 Measuring distances and bearings ... from your boat You can determine the position, distance and bearing from your boat to the position of the cursor by referring to the cursor position (Csr Pos) data in the databar. ... between two points on your chart The ruler option of your chart application can be used to obtain an accurate measurement of the distance and bearing between two points on your chart. To position the ruler 1.
56 C-Series Display Reference Manual 4.9 Navigating to a specific point You can use your chart to navigate to a specific point marked by the cursor (temporary waypoint) or to a waypoint. If required you can display the largest chart scale possible that will display both your boat and the target waypoint. When you navigate to a waypoint or to the cursor position, the data is sent on NMEA 0183 and SeaTalk and can be used by an autopilot, if connected.
Chapter 4: Using the Chart 57 Go to an existing waypoint You can navigate to an existing waypoint by either selecting the appropriate waypoint on-screen with the cursor or by selecting it from the waypoint list: Note: For more information on navigating with Waypoints, please refer to Chapter 3:Working with Waypoints. ... selected with the cursor This option navigates you to the waypoint that you select on screen. GO TO WAYPOINT Position cursor over required waypoint.
58 C-Series Display Reference Manual NAVIGATION ALARM D8325_2 Waypoint Arrival To de-activate the arrival alarm Or ACKNOWLEDGE D8326_1 Wait 10 seconds Stop navigating to your target waypoint To stop navigating towards the selected waypoint: GOTO... STOP GOTO D8324_1 o Maintaining a view of your navigation By selecting Auto Range mode, your chart will automatically adjust the range to maintain both your boat and the target waypoint on screen, using the largest scale possible.
Chapter 4: Using the Chart 59 4.10 Building and following a route FOLLOW ROUTE OPTIONS ... BUILD NEW ROUTE ... REVIEW AND EDIT ROUTES ... D6534-2 SHOW/HIDE ROUTES ... This section describes how to use routes and includes the following: • What is a route? • What can I do with a route? • Building and saving a route. • Following a route. • Viewing details of routes. Once created you have the option to view a route’s details, amend its course, edit its name and color or erase it.
60 C-Series Display Reference Manual Building a route Routes can either be built on screen or via the waypoint list. A route consists of: • New waypoints that you have specifically placed for that route Or: • Existing waypoints that are already stored in the system Or: • A combination of new and existing waypoints. Note: A route can also be created from a track. See page 80 for details. Up to 100 routes can be added to your system, each consisting of up to 50 waypoints.
Chapter 4: Using the Chart 61 3. Continue entering waypoints. If you make an error, you can remove the last waypoint (see page 62 for details). 4. Save your route when it is complete (see page 63 for details). 4nm North-Up (Relative Motion) Sunday Trip# PORT POINT Local RTE Sunday Trip# GULLY RIDGE Portside Port point Sunday Trip# CREEK VIEW PORTSIDE SHOW/HIDE ROUTES… FOLLOW ROUTE OPTIONS… BUILD NEW ROUTE REVIEW AND EDIT ROUTES… D6546_2 CREEK POINT ...
C-Series Display Reference Manual BUILD NEW ROUTE ROUTES... USE WAYPOINT LIST D6498-3 62 2. Select and insert the first waypoint in the new route: Make Route New Route Waypoints Crag Rock Blyth Bay Sandy y Bay y INSERT WAYPOINT New Route 01 Sandy Bay Waypoint added to New Route. Highlight required waypoint D8355-1 Make Route Waypoints Crag Rock Blyth Bay Sandy Bay 3. Continue entering waypoints until your route is complete.
Chapter 4: Using the Chart 63 The waypoint and its dotted line are removed from the screen and the cursor moves back to the previous waypoint. If you repeatedly press these keys, successive waypoints are removed.
64 C-Series Display Reference Manual Following a route When you are following a route the active route is shown on all chart windows. When the distance to the next waypoint in the route is less than that specified for the arrival alarm radius (see page 188), or your boat reaches the closest point of approach to the target (defined by a line passing through the waypoint and perpendicular to the route leg), a warning dialog is displayed and an alarm sounds (see page 57).
Chapter 4: Using the Chart 65 Follow using the cursor You can either use the cursor to select and follow a route from the start of the route or from a selected waypoint within the route. ... from the start of the route FOLLOW THIS ROUTE D7510-2 Position cursor over any leg of required route ...
66 C-Series Display Reference Manual Advance to the next waypoint in a route If you are following a route, you have the option to advance to the next waypoint in that route. W.Wight 1 2 Example: In this example, the advance waypoint option was selected following arrival at Waypoint 2. 3 This has resulted in Waypoint 3 being dismissed and the course of the route advancing to Waypoint 4. 4 D6603_3 W.
Chapter 4: Using the Chart 67 Viewing details of routes Details of all routes that you create are held in the Route List. You can: • View the route list and then select the required route, or • Select the required route on-screen. The TIME and SOG options can then be used to aid passage planning by displaying the time in hours or as an ETA and the SOG as actual or planned.
68 C-Series Display Reference Manual ETA TIME HOURS and/or ROUTE DETAILS... Toggle as required D8998_1 SOG ACTUAL PLANNED 4.11 Editing routes Once you have created a route, it can be edited in a variety of ways. You can: • Reverse a route (see page 65) • Amend the course of a route (see page 69). • Change the name of a route (see page 73). • Change the color of a route (see page 73). • Erase a route (see page 73). Note: An active route can be edited, with the exception of the target waypoint.
Chapter 4: Using the Chart 69 Editing the selected route Once you have selected the appropriate route (see previous section) you can proceed to edit it. Reversing a route You can reverse the course of a route: 4 1 2 3 BayView 3 2 REVERSE ROUTE BayView Select appropriate route with cursor 4 Waypoints renumber and route name moves D6541-4 1 Note: For details of how to reverse and immediately follow a route, see page 65.
70 C-Series Display Reference Manual 3. Select the start of the route and the waypoint for insertion: Waypoints Harbour Ent. Midchannel Outer Harbour Pierhead Waypoint 4 50016'.75N 00106'.095W Make Route Sunday tour 01 02 03 Waypoints Harbour Ent. Midchannel Outer Harbour Pierhead Waypoint 4 Midchannel Outer Harbour Harbour Ent. 50047'.356N 00106'.604W 50016'.75N 00106'.095W Sunday tour 01 02 03 Midchannel Outer Harbour Harbour Ent. 50047'.356N 00106'.604W Move control to route column.
Chapter 4: Using the Chart 71 To add a waypoint within a route: PLACE WAYPOINT INSERT WAYPOINT RTE Stretch to position for new waypoint Route course changes Route index renumbers D8373_1 RTE Move cursor over appropriate leg of route Note: You can also use the method described on page 69, to add a waypoint within a route. Add a waypoint(s) to the end of a route This option inserts a waypoint (or series of waypoints) at the end of a route in order to extend its existing course.
72 C-Series Display Reference Manual 4. Select waypoint to be added: Add new waypoint at cursor 3 1 PLACE WAYPOINT RTE 2 New leg added to end of route. Or: Use existing waypoint Make Route USE WAYPOINT LIST... 50016'.75N 00106'.095W Sunday tour 01 Midchannel 02 Outer Harbour 03 Harbour Ent. 50047'.356N 00106'.604W D8381_1 Waypoints Harbour Ent. Midchannel Outer Harbour Pierhead Waypoint 4 New leg added to end of route. 5.
Chapter 4: Using the Chart 73 Changing the name or color of a route You can change the name of a route from the default to a more meaningful one and/or change the color if required. This will make them easier to distinguish from one another, particularly if you have numerous routes in your system. 1. Select the appropriate route for editing (see page 68). 2. Select the Edit Name or Edit Color option: EDIT NAME Edit Route Name R t 1 Route EDIT NAME AND COLOR...
74 C-Series Display Reference Manual 4.12 Monitoring where you are going ... using chart vectors You can display a variety of graphical indicators to help monitor where you are going: Note: Any vectors applied to a chart window that is set to system view, will be displayed in all other system view chart windows. Heading (HDG) and course over ground (COG) vectors Heading vector (HDG) D6772-2 Course over ground (COG) The ship’s heading (HDG) is displayed as a line with an open arrow head.
Chapter 4: Using the Chart 75 ... using the Course Deviation Indicator (CDI) D6895-2 The CDI assists with accurately maintaining your course to your destination. A ‘rolling road’ in three dimensional perspective provides a real-time display of your boat’s course. See Chapter 8:Using the Course Deviation Indicator for more information. 4.
76 C-Series Display Reference Manual 4.14 Using the radar with the chart You can enhance the use of your chart by combining it with the following radar features: • Radar range synchronization • MARPA. • Radar overlay. Synchronizing the chart with radar range When synchronization is switched on: • The radar range in all radar windows, changes to match the chart scale. • ‘Sync’ is indicated in the top left-hand corner of the chart window.
Chapter 4: Using the Chart 77 Distinguishing between fixed and moving objects You can overlay radar image data over your chart image allowing better distinction between fixed objects and other marine traffic. For best results, switch on Radar-Chart synchronization (see page 76) to ensure radar range and chart scale are synchronized. To switch radar overlay on: 1.
78 C-Series Display Reference Manual Changing the radar range from the chart window When the radar overlay is set to ON, the radar range is indicated in the top left-hand corner of the chart window in the same color as the overlay. You can now change the radar range: OUT RADAR OPTIONS... RANGE D6585-1 D7217-3 IN Note: If RDR RNG SYNC is set to ON (see page 76), the chart scale also changes 4.
Chapter 4: Using the Chart 79 How can I use tracks? Tracks can be used to: • Review where you have been. • Retrace your original journey by converting the track to a route and automatically reversing it. If required, a track can be personalized and the track options customized to your own particular needs. You can: • Rename a track. • Change the color of a track. • Specify the time period between track point creation (see page 90). • Specify the distance between each track point (see page 90).
80 C-Series Display Reference Manual Creating a route from a track Creating a route from a track enables you to retrace the course of that track. When a track is converted the system creates the closest route through the recorded track, using the minimum number of waypoints. Each waypoint created will be saved with the depth and temperature data (if applicable) for that position.
Chapter 4: Using the Chart 81 ...from a saved track You can create a route from a track that you have already saved: To name the route CREATE ROUTE FROM TRACK… TRACK Route generated and dialog box displayed Position cursor over track YES Or: NO To accept default (numbered) D8368_1 Route generation completed. Maximum deviation from oritinal track equals 0,001nm. Please check route before navigating.
82 C-Series Display Reference Manual Editing the selected track Once you have selected the appropriate track (see previous section) you can proceed to edit it. Changing the name or color of a track You can change the name of a track from the default to a more meaningful one and/or change the color if required. This will make them easier to distinguish from one another, particularly if you have numerous tracks in your system. 1. Select the appropriate track for editing (see page 81). 2.
Chapter 4: Using the Chart 83 4.17 Defining how the chart windows are presented Each chart window can be tailored to meet your particular needs. You can: • Set the chart view for individual windows or system wide (see below). • Change how the chart is orientated (see page 84). • Change the way your chart is drawn in relation to your boat movement (see page 85).
84 C-Series Display Reference Manual Setting the orientation of the chart The orientation of a chart refers to the relationship between the chart and the direction that you are travelling in. It is used in conjunction with motion mode (see page 85) to control how your boat and chart relate to one another and how they are displayed on screen. The mode that you choose is restored at power up.
Chapter 4: Using the Chart 85 Setting the motion mode The motion mode controls the relationship between the chart and your boat. Whilst motion mode is active, as your boat moves, the chart is redrawn to keep the boat onscreen. The three motion modes are: • Relative motion. • True motion. • Autorange. When you pan the chart or toggle FIND SHIP/CURSOR to CURSOR, the motion mode is suspended.
86 C-Series Display Reference Manual D6840_2 In the following example the motion mode has been set to Relative with a vessel offset of 1/3. The boat is fixed in the offset position and the chart moves accordingly: True motion (TM) When the motion mode is set to True, the chart is fixed and the boat moves in true perspective to fixed landmasses on the screen. As the boat’s position approaches the edge of the screen, the chart picture is automatically reset to reveal the area ahead of the boat.
Chapter 4: Using the Chart 87 Showing or hiding waypoints/waypoint information The system has various options to control the display of waypoints and waypoint information. You can show or hide all your waypoints and their names or show or hide waypoints by group or by symbol. These options are particularly useful when you have placed a large number of waypoints in a small area and rendered your chart difficult to interpret.
88 C-Series Display Reference Manual Showing or hiding a route or a track You can define which routes or tracks are shown or hidden from the screen. When a route is set to HIDE, the route line is not displayed. The display of waypoints within a hidden route depends however on the show/hide waypoint setting (see page 87). The active route is always displayed irrespective of the display status.
Chapter 4: Using the Chart 89 Routes ROUTE ON CHART SHOW Set to SHOW or HIDE as required Highlight required route Or Tracks TRACK ON CHART SHOW Set to SHOW or HIDE as required D8389-1 Highlight required track Showing or hiding cartographic features If there are a large number of cartographic objects in a particular area, you can reduce the amount of detail by de-cluttering the chart display. Turning declutter on hides the following cartographic objects: • Text. • Chart boundaries. • Spot soundings.
90 C-Series Display Reference Manual 4.19 Setting up your chart and its cartography The set up for your chart and its cartography can be changed from the standard configuration to suit your particular needs. Although you will probably only do this when you first use the chart, you may decide to make subsequent adjustments once you become more familiar with the system. Any settings that you change are retained even when you power off.
Chapter 4: Using the Chart 91 FUNCTION OPTIONS Description (Default in bold) Track Interval Options available depend on setting in Record Vessel Track By function: TIME - specify time period between track points creation. DISTANCE - specify distance between track points creation. AUTO - no options available TIME selected: 1 sec 5 secs 10 secs 30 secs 1 min 3 min 5 min 10 min 30 min DISTANCE selected: 0.1 nm 0.5 nm 1.
92 C-Series Display Reference Manual Important: Any offset entered will be applied to all charts on the chart card. You should therefore ensure that this feature is switched off once you have transitioned off of the errant chart. Any charting errors that you discover should be reported to Navionics (see page 201). To switch on chart offset: Alarm Setup Menu Object Information Vector Length Points ON Infinite Datum Chart Offset...
Chapter 4: Using the Chart 93 CLEAR OFFSET D8393_1 SET OFFSET... Cartography Setup The Cartographic Setup Menu allows you to configure what is displayed on your chart: To select the Cartography Setup Menu: Setup MENU Chart Setup... Cartography Setup... GPS Status... Compass Setup...
94 C-Series Display Reference Manual FUNCTION Description OPTIONS (Default in bold) Depth Contour A line indicating the depth at a particular position. ALL 16ft 19ft 32ft 65ft OFF Nav. Marks ON OFF Nav. Marks Symbols The set of symbology used for navigation marks. Corresponds to paper charts. International US Light Sectors The sector of light cast by a fixed beacon.
Chapter 5: Using the Fishfinder 95 Chapter 5: Using the Fishfinder 5.1 Introduction This chapter describes how the Fishfinder uses sonar to see fish, bottom structure and texture, and underwater obstructions such as wrecks. The standard fishfinder image is a historical, scrolling bottom graph at an automatically selected range and frequency.
96 C-Series Display Reference Manual 5.3 What can the fishfinder show me? When you first view the fishfinder application, an image representing the echoes seen by the DSM is displayed. As time passes this image scrolls from right to left and becomes a record of the echoes seen. The images at the right hand side of the display are therefore the most recent. The fishfinder window will display: • The bottom together with any bottom structure such as reefs and shipwrecks etc. • Target images indicating fish.
Chapter 5: Using the Fishfinder 97 Interpreting the bottom structure The bottom usually produces a strong echo. These images indicate the bottom conditions as follows:. A hard bottom (sand) produces a thin line A soft bottom (mud or seaweed cover) produces a wide line. The dark layer indicates a strong signal. D6855-2 A rocky or uneven bottom or a wreck produces an irregular image with peaks and troughs The dark layers indicate a good echo; the lighter areas weaker echoes.
98 C-Series Display Reference Manual Note: The depth of individual targets can be displayed by switching on the Target Depth ID in the Fishfinder Setup Menu. The number of target depths displayed is influenced by the fish alarm sensitivity level (see page 188). Target depth D6890-2 Target The size of the target The larger the target, the larger the return on the fishfinder display. The size of a fish target is however dependent upon the size of the fish’s swim bladder rather than its overall size.
Chapter 5: Using the Fishfinder 99 There are three A-Scope modes which are selected for individual fishfinder windows: I MODE 2 The left-hand side of the Mode 1 image is expanded to give a more detailed view. MODE 1 The A-scope image is centred in the window. MODE 3 The A-scope image angles outward as signal width increases with depth. D6674-3 To display the A-Scope image: 1. Select the A-Scope option: A-scope image Standard fishfinder image 0 20 A-SCOPE...
100 C-Series Display Reference Manual 5.4 Enhancing what you see You can enhance the image by applying the following options: • Change the range (Range). • Shift the selected viewing range (Range Shift). • View a zoomed area (Zoom). • Flatten the bottom image to help separate fish from the bottom (Bottom Lock) • Isolate bottom fish (White Line/Bottom Fill) • Pause the scrolling image or adjust the rate at which the image scrolls (Scroll Pause/ Scroll Speed) • Change the size of or remove the depth digit.
Chapter 5: Using the Fishfinder 101 Zooming in on the bottom If necessary you can zoom in on the bottom to display more detail. This zoom option enables you to: • Replace the standard fishfinder image with the zoomed image or display the zoomed image alongside the standard fishfinder image. • Set to zoom level to one of the pre-defined zoom factor levels or adjusted manually. • Reposition the portion of the image to be zoomed, if required.
102 C-Series Display Reference Manual Selecting the zoom factor When the zoom function is active (ZOOM ON or ZOOM SPLIT), you can select either a predefined zoom factor or you can adjust the zoom factor manually. Pre-defined zoom factor Select x2, x3 or x4 for a predefined zoom level. The greater the factor, the smaller the area you are viewing and therefore the smaller the zoom box. These factors are proportioned to the range e.g. x2 x3 x4 ZOOM FACTOR x2 ZOOM...
Chapter 5: Using the Fishfinder 103 Simplifying the bottom image When you are looking for fish that feed close to the bottom, you can use the Bottom Lock function to filter out and flatten the bottom structure and display the fish (or any other objects directly above the bottom) more clearly. Bottom Lock is selected for individual fishfinder windows and can either replace (ON) or appear alongside (SPLIT) the standard fishfinder image.
104 C-Series Display Reference Manual Isolating bottom fish You can separate the echoes from fish near the bottom and from the bottom itself by using the White Line and/or the Bottom Fill features. Gain: Auto High 200 kHz: Auto Standard fishfinder image The standard fishfinder image displays the bottom as a combination of features (mud, sand, fish targets etc) with various sonar signal strengths. 75 75.
Chapter 5: Using the Fishfinder 105 BOTTOM FILL ON PRESENTATION... OK and/or D6678-3 WHITE LINE ON Changing how the image scrolls Adjusting the scroll mode and speed You can adjust the speed at which the display scrolls, but the same section of the bottom is displayed regardless of scrolling speed. A faster speed displays more detail. This is useful when you are looking for fish. If you select a slower speed the information remains on the display for longer.
106 C-Series Display Reference Manual Pausing the scrolling image You can pause the display to see a ‘snapshot’ of the image. When a display is paused, scrolling stops but the depth indication continues to be updated.Scroll pause/resume affects the currently selected fishfinder frequency (200kHz, 50kHz or BOTH). If you are in dual frequency mode (see page 114), you can pause one frequency while the other continues to scroll.
Chapter 5: Using the Fishfinder 107 Fishfinder Setup Menu Depth Digit Size Depth Digit Position Target Depth ID Depth Lines Color Palette Scroll Manual Scroll Speed MENU GPS Status... Compass Setup... Enter Fishfinder Setup menu LARGE BOTTOM OFF OFF Copper MANUAL 100% Select required digit size and position D8450_1 Setup Fishfinder Setup... Note: No matter what size is selected, the Depth Digits will auto-shrink (when neces- sary) to fit in the available space.
108 C-Series Display Reference Manual 5.6 Determining depths and distances of targets The fishfinder provides various features to determine depths and distances: Gain: Auto High 200 kHz: Auto VRM marker indicating distance behind boat Depth line VRM marker indicating depth of target 48 49 63 69 69 74 73 74 70 74 78 ON VRM 1 OFF RANGE 0.787nm 78 DEPTH 44.
Chapter 5: Using the Fishfinder 109 Measuring using VRMs You can use a Variable Range Marker (VRM) to determine the depth and distancebehind-boat of an object. These markers consist of a horizontal (depth) line and a vertical (distance-behind-boat) line; each of which are marked with the appropriate measurement and are controlled individually. Note: VRMs set up in Fishfinder are unrelated to those set up in Radar. 1. Select the VRM option: VRM VRM... ON D8453_1 PRESENTATION... Toggle to ON 2.
110 C-Series Display Reference Manual 5.7 Fishfinder alarms In addition to the system alarms (see page 187), the following alarms can be set when you are connected to a DSM or when the simulator is on: • Fish Alarms - sound when a target meets the specified sensitivity level and, is within the depth limits (if enabled). The greater the fish alarm sensitivity, the greater the number of target image depths displayed.
Chapter 5: Using the Fishfinder 111 Display settings The display settings provide controls to change the fishfinder image.
112 C-Series Display Reference Manual Transducer Calibration The C-Series display receives the image from a DSM which processes sonar signals from a transducer mounted in the water. If the transducer is equipped with a speed paddle wheel and temperature-sensing thermistor, the DSM calculates speed and temperature. To ensure accurate readings it may be necessary to calibrate the transducer(s) by applying offsets to depth, speed and temperature.
Chapter 5: Using the Fishfinder 113 DSM Setup Certain conditions, such as a hard bottom or other vessels equipped with a fishfinder, may affect the DSM. The following DSM Setup controls enable you to change settings to allow for this. As they are held in the DSM, they are applied system-wide. OPTIONS MENU ITEM (Default in bold) DSM Reset... Restore all settings on the DSM to factory default. When performing a DSM Reset, it is normal to briefly loose connection with the DSM. YES NO Trip Counter Reset.
114 C-Series Display Reference Manual 5.9 Other settings affecting the fishfinder image The system automatically adjusts the following settings in order to optimize the fishfinder image: • Operating frequency. • Gain modes (Gain, Color Gain, TVG) • Power setting. They should not ordinarily require adjustment. You can however make adjustments manually if required. Operating frequency modes The operating frequency is indicated in the status bar.
Chapter 5: Using the Fishfinder 115 Dual frequency mode In dual frequency mode the DSM pings at the same rate but alternates between 200 kHz and 50 kHz. This allows you to select the required frequency(s) - 50kHz, 200 kHz or BOTH for each individual fishfinder window. Combine this mode with the zoom, bottom lock and A-scope functions to customize each fishfinder window to meet your particular requirements or fishing conditions.
116 C-Series Display Reference Manual The gain, or sensitivity, of the display adjusts background noise by varying the echo strength for display. The value of the GAIN control determines the strength above which echoes are displayed. There are three AUTO GAIN modes: • Low is ideal for viewing fishfinder images with a minimum of background noise as you are cruising to your fishing spot. Only the strongest echoes are displayed.
Chapter 5: Using the Fishfinder 117 TVG (Time Varied Gain) The TVG (Time Variable Gain) reduces the clutter by varying the gain throughout the water column. This function is useful for reducing the appearance of ‘noise’. Increasing the TVG value increases the maximum depth to which TVG is applied. Decreasing it reduces the maximum depth. A low TVG value has little effect on gain in shallow water; a high value decreases the gain in shallow water so that only the strongest echoes are displayed.
118 C-Series Display Reference Manual To adjust the Power Setting: 1. Select the power setting function: POWER AUTO D8460_1 FISHFINDER SETTINGS... Press to highlight 2.
Chapter 6: Using the Radar 119 Chapter 6:Using the Radar 6.1 Introduction This chapter describes the basics of radar and the things that can affect your radar picture. It then shows you how to use your radar and its various functions including: • Changing orientation and motion mode. • Getting the best radar picture. • Measuring distances and bearings. • Collision avoidance using Guard Zones, MARPA and AIS. • Using waypoints to mark positions. • Setting up the radar display. • Radar alarms.
120 C-Series Display Reference Manual Maximum radar range Maximum radar range is essentially line-of-sight, so is limited by the height of the scanner and the height of the target as illustrated below: Rmax a1 h a2 Earth Radar Rmax = 2.
Chapter 6: Using the Radar 121 Side lobes Side lobe patterns are produced by small amounts of energy from the transmitted pulses that are radiated outside the narrow main beam. The effects of side lobes are most noticeable with targets at short ranges (normally below 3 nm), and in particular with larger objects. Side lobe echoes form either arcs on the radar screen similar to range rings, or a series of echoes forming a broken arc.
122 C-Series Display Reference Manual Multiple echoes Multiple echoes are not very common but can occur if there is a large target with a wide vertical surface at a comparatively short range. The transmitted signal will be reflected back and forth between the target and your own ship, resulting in multiple echoes, displayed beyond the range of the true target echo, but on the same bearing.
Chapter 6: Using the Radar 123 Rain or snow clutter D3967-4 The radar can see echoes from rain or snow. Returns from storm areas and rain squalls consist of countless small echoes that continuously change size, intensity and position. These returns sometimes appear as large hazy areas, depending on the intensity of the rainfall or snow in the storm cell. Interference D6601-2 When two or more radar-equipped vessels are operating within range of each other mutual radar interference can occur.
124 C-Series Display Reference Manual 6.3 Powering on/off the various scanner operating modes To control the power to the radar: SCANNER OFF Switch scanner ON or OFF RADAR TX Select required operating mode D8397_1 SCANNER ON The scanner icon in the data bar indicates the chosen status and is described as: Radar Mode Radar status icon Scanner on and transmitting. When SCANNER set to ON, select this mode to activate scanner. This is the usual mode of operation.
Chapter 6: Using the Radar 125 6.4 The radar picture You will need heading and position data for full functionality of your radar. A fast heading sensor is also needed for operation of MARPA and can maximize the performance of radar/chart overlay. With your radar scanner connected and the radar in transmit mode, the radar picture, provides a map-like representation of the area in which the radar is operating e.g.
126 C-Series Display Reference Manual from the coastline. Although the coastline may be much nearer, it may not appear on the radar until the vessel is closer to shore. • Some targets, such as buoys and small boats, can be difficult to discern, because they do not present a consistent reflecting surface as they bob and toss about in the waves. Consequently, these echoes tend to fade and brighten and at times, to disappear momentarily.
Chapter 6: Using the Radar 127 screen. Any changes that you make to the orientation of the radar are retained when you switch off. Head Up (H-UP) This is the default mode for the radar application. e.g: N Ship's Heading Market (SHM) (indicating the boat's current heading) is upwards As your boat's heading changes: SHM fixed upwards Radar picture rotates accordingly D8398_1 N North Up (N-UP) e.
128 C-Series Display Reference Manual Course Up (C-UP) e.g: N As your boat's heading changes: Radar picture fixed SHM rotates accordingly Current course upwards D8400_1 N If you select a new course, the picture will reset to display the new course upwards. The reference used for Course-Up depends upon the information available at a given time. The system always prioritizes this information in the following order.: 1. Bearing from origin to destination, i.e. intended course. 2.
Chapter 6: Using the Radar 129 Relative motion (RM) with optional vessel offset When the motion mode is set to Relative, the position of your boat is fixed on the screen and all the targets move relative to the boat. 0 offset 1/ offset 3 2/ offset 3 D6842-2 You can specify whether the boat is fixed in the centre of the window (0 offset) or offset by 1/3 or 2/3 to increase the view ahead i.e. The default mode for the radar application is Relative with zero offset.
130 C-Series Display Reference Manual Showing or hiding the range rings To turn the range rings on/off: RANGE RINGS OFF ON Toggle as required D6897-2 PRESENTATION Changing the bearing mode for EBLs The default bearing mode for EBLs is relative to your vessel’s heading. If heading data is available, you can set the bearing mode to be relative (REL), magnetic/true (M/T). When M/T is selected, the EBL bearings will be expressed as either true or magnetic dependant on the equipment connected.
Chapter 6: Using the Radar 131 Sea Radar echoes from waves around your boat can clutter the centre of the radar picture, making it difficult to detect real targets (see page 122). Adjusting the sea mode will reduce this clutter for up to 5 nautical miles (depending on wave and sea conditions) from your boat. This has the effect of reducing the sea echoes to intermittent small dots whilst small targets remain visible and persistent. Gain levels further from your boat remain unchanged.
132 C-Series Display Reference Manual Manual (MAN) mode If you do set the TUNE function to MANUAL, you will need to adjust it about 10 minutes after you have turned on the radar, since the required setting will change after the magnetron has warmed up. You should adjust the control to obtain the maximum signal strength (indicated by the eight step horizontal bar.). If you cannot tune the radar successfully, refer to the Installation Guide.
Chapter 6: Using the Radar 133 Setup Radar Setup Menu Interference Reject NORMAL Target Expansion LOW Wakes Period 1 min Radar Setup... GPS Status... Compass Setup... Highlight Radar Setup OK Select Interference Reject Select Radar Setup D8414_1 MENU Select NORMAL or HIGH Note: This menu can also be selected by pressing and holding INT. REJECT. If you wish to detect the presence of other radars in the vicinity: ENHANCE ECHOES...
134 C-Series Display Reference Manual Wakes When the wakes function is switched on, you can see the direction and speed of moving targets relative to your boat. A target is displayed in yellow and as the signal diminishes with time it is shown in paler shades of blue. Displaying wakes To switch on the wakes function: D8421_1 WAKES ON ENHANCE ECHOES...
Chapter 6: Using the Radar 135 6.8 Changing the displayed range You can zoom in or out to view your radar picture at varying scales. The scale is measured from the centre to the top of the window and is displayed in the left-hand corner of the status bar.
136 C-Series Display Reference Manual 6.9 Measuring distances, ranges and bearings When you are using the radar application, you can measure distances, ranges and bearings in a variety of ways. These options are detailed in the table below: Functions Distances between points Range from your boat Bearings Range Rings Yes (approx.) Yes (approx.) - Cursor - Yes Yes Variable Range Markers (VRMs) - Yes - Electronic Bearing Lines (EBLs) - - Yes Floating VRMs Yes - - Floating EBLs Yes .
Chapter 6: Using the Radar 137 ... Using VRMs and EBLs What is a VRM? VRM A Variable Range Marker (VRM) is a circle centred on your vessel’s position and fixed with respect to the heading mode. When this circle is adjusted to align with a target, its range from your boat is measured and displayed on the ADJUST VRM soft key. D8408_1 The data is also displayed if you select the VRM with the cursor.
138 C-Series Display Reference Manual Tracking a target with a VRM/EBL You will be able to tell which way the target is traveling by watching how it moves in relation to the EBL. If it continues traveling directly along the EBL, it shows that it is on a possible collision course with your boat - take the appropriate action. Creating a VRM and/or EBL To use VRMs and EBLs to tell you the range and bearing of a target: 1. Select the VRM/EBL 1option: VRM/EBL 1 ON VRM/EBL...
Chapter 6: Using the Radar 139 ... Using floating VRMs/EBLs You can use the VRM/EBL float function to measure the range and bearing between any two points on the radar screen. This function allows you to move the VRM/EBL centre away from your boat’s position and onto a target. You can then change the radius of the VRM to determine the distance between two points and change the angle of the EBL, relative to its new origin, to obtain the bearing. Floating a VRM/EBL 1.
C-Series Display Reference Manual ADJUST VRM 1900 ADJUST EBL xxx0 Move EBL over 2nd target Bearing between 1st & 2nd target on soft key OK To save & remove highlight D8431_1 140 5. If required, you can float a second VRM/EBL: i. Press SET UP VRM/EBL 2. ii. Toggle the VRM/EBL 2 to ON. iii. Repeat steps 1 to 8 above. Unfloating a VRM/EBL To unfloat VRM/EBLs and return them to the central position: 1. Select the VRM/EBL option. 2. Unfloat VRM/EBL 1 or 2: To unfloat VRM/EBL 1: FLOATING EBL...
Chapter 6: Using the Radar 141 maintained. A guard zone only operates when the whole zone is displayed on the screen. An audible alarm sounds to alert you when a target enters the zone. Guard zones are inactive for 10 seconds after being placed or re-sized, to avoid inappropriate alarms whilst they are being positioned. You can set up guard zones to be either sector zones or 360° (circular) zones. Your radar can be set up using one or two zones.
142 C-Series Display Reference Manual Repeat for other settings SET INNER xx.xx nm Press to highlight OK Set inner limit for guard zone D6761_3 ZONE SHAPE CIRCLE Circular guard zone 6nm Head-Up D6832-2 Circular Guard Zone To set up a circular guard zone: Repeat for other settings SET INNER xx.
Chapter 6: Using the Radar 143 MARPA SAFETY NOTICES MARPA can improve collision avoidance when used wisely. It is the User’s responsibility to exercise common prudence and navigational judgements. There are conditions where acquiring a target may become difficult. These same conditions may be a factor in successfully tracking a target. Some of the conditions are: • The target echo is weak. The target is very close to land, buoys or other large targets.
144 C-Series Display Reference Manual How is a risk assessed? Each target is monitored to see if it will be within a certain distance from your boat within a certain time. If so, the target is designated as dangerous and an audible warning is sounded along with an on-screen warning being shown. The target symbol changes to the dangerous target symbol and flashes to indicate that it is a dangerous target. Pressing the appropriate soft key will silence the alarm and remove the warning.
Chapter 6: Using the Radar 145 D6810_4 MARPA targets CPA graphics CPA graphics show vectors for your vessel and a selected target. A vector is a line onscreen showing the predicted courses of your vessel and the selected target if you both remain on your present course. These vectors vary in length due to boat speed and vector length set in the MARPA Setup menu. Vector CPA graphic 9 D9008_1 3 0 181 T 17.
146 C-Series Display Reference Manual True mode With the display set in True mode, the vectors of your vessel and the target are shown extended to their intersection point. The CPA is shown as a line that is placed on your boat’s vector at the point of the CPA. The length and direction of the line indicates the distance and bearing of the target at CPA. The text indicates CPA and TCPA. The text next to the target symbol indicates its true course and speed.
Chapter 6: Using the Radar 147 Acquiring a target to track 1. Select target to be acquired: Target Move cursor over target to be acquired D6829-2 TARGET TRACKING... 2. Acquire target: 'Target being acquired' symbol displayed If target present for several scans, the radar will lock onto it and change the symbol to 'Safe' D8806-1 ACQUIRE TARGET Note: If set to ON, the CPA graphic is displayed. Cancelling targets ...
148 C-Series Display Reference Manual To cancel an individual target: MARPA LIST... ID Bearing Range Course Speed 1 2 1370T 1870T 1.4nm 4.0nm 1800T 1300T CPA TCPA 2.2kt 1.4nm 2min 1.5kt 4.
Chapter 6: Using the Radar 149 Radar Setup Menu Setup MENU GPS Status... Compass Setup... System Setup... Highlight Radar Setup menu Enter Radar Setup menu Active Scanner 2kw Radome Interference Reject Target Expansion Wakes Period NORMAL LOW 1min Timed Transmit Transmit Period Standby Period OFF 10 SCANS 3 MINS Sea Clutter Curve... Antenna Size Bearing Alignment Radar Advanced Setup...
150 C-Series Display Reference Manual 6.12 Warnings of potential dangers If switched on, the following alarms will be triggered when you are in the radar application: • System alarms - anchor, timer, alarm clock and temperature. • Navigation alarms - arrival and off track. • Radar alarms - guard zones. • Fishfinder alarms. • AIS alarms. • Depth alarms. • Data alarms. • External SeaTalk alarms.
Chapter 7: Using the data application 151 Chapter 7: Using the data application 7.1 Introduction D9010_1 The data application enables you to view numeric data generated by the system or by instruments available on NMEA or SeaTalk. 7.2 Selecting a data application To select a data application: 1. Select a page set that includes a data application: PAGE OK Highlight suitable page set with Digital Data application 2.
152 C-Series Display Reference Manual 7.3 Selecting the data for display You can either select a panel of pre-configured data or customize the application to display the data of your choice. Note: Panel selection is a local setting and will therefore only affect the individual dis- play on which you are working.
Chapter 7: Using the data application 153 To select a pre-configured data panel: e.g. ACTIVE Move control to Digital Data window Select page including Digital Data application Select required panel type Selected panel type displayed D8466_1 WAYPOINT Customize the panels You can customize each panel by changing: • The panel name. • The size and number of data cells • The data contained in each cell.
154 C-Series Display Reference Manual Selecting cell data To select the data that is to appear in each cell: 1. Select the data group for the relevant panel e.g. Data Groups e.g. SAILING SELECT DATA... Press and hold relevant soft key Vessel Navigation Depth Environment Wind Time and Date Engine Select data group D9106_1 Highlight data group 2.
Chapter 7: Using the data application 155 = Split horizontally e.g. e.g. Heading 2960T Heading 2960T Speed 20.0kt Trip 13.85nm Cell for splitting selected SPLIT CELL Speed 20.0kt OK Depth Trip 48.5ft 13.85nm Soft key indicates direction of split Cell splits horizontally OR Split vertically e.g. e.g. Heading 2960T Heading 2960T Speed 20.
156 C-Series Display Reference Manual
Chapter 8: Using the Course Deviation Indicator 157 Chapter 8: Using the Course Deviation Indicator 8.1 Introduction With your display receiving accurate heading and position information, you can use the Course Deviation Indicator (CDI) to monitor your course and accurately steer to a target waypoint. The CDI application is pre-configured to display the CDI graphic. You can customize the panel to display any available data. 8.
158 C-Series Display Reference Manual Steering instructions The steering instructions below the rolling road tell you what correction is needed to maintain your course and arrive at the target waypoint.
Chapter 9: Using the Engine Monitor 159 Chapter 9: Using the Engine Monitor 9.1 Introduction The engine monitor application enables you to view information in the form of gauges and digital data, from up to three compatible engines. To provide a fast update rate, the engine data is transferred from the engine’s serial interface to your C-Series display via NMEA2000/SeaTalk2. Note: For details of compatible engines and related software updates, please refer to the Raymarine website on www.raymarine.com.
160 C-Series Display Reference Manual i. With an engine monitor window active, select the Panel Setup Menu: Setup Panel Setup Menu... MENU GPS Setup... D8707_1 Select Panel Setup Menu ii. Set the number of engines: Panel Setup Menu Configure: Configure: Configure: Configure: Configure: ENGINE... ENGINE & FUEL... FUEL RESOURCES... ENGINE & RESOURCES... TWIN ENGINE...
Chapter 9: Using the Engine Monitor 161 9.3 The engine monitor display Engine data is displayed in a series of pre-configured panels. Each panel contains a particular set or data. You can choose the panel that suits your requirements via the soft keys: Panel Type Engine Engine & fuel Fuel resources Engine & resources Twin engines Tacho & engine hours Oil pressure Data content Engine coolant temperature Boost pressure Alternator Fuel level (tanks 1 & 2) Total fuel D9105_1 Fuel rate 9.
162 C-Series Display Reference Manual
Chapter 10: Navtex 163 Chapter 10: Navtex 10.1 Overview The display can be used to view marine safety information including weather forecasts and marine warnings received from a Navtex receiver. You can select the type of warning message that will trigger this alert on your display. Once you have read the received message you can either erase or save it. Your system can store up to 100 messages. Once capacity is reached the oldest messages are automatically deleted to allow for new incoming messages.
164 C-Series Display Reference Manual 10.4 Viewing messages Displaying the Navtex Message List To view messages stored in your system: Setup Radar Setup... MENU GPS Setup... Compass Setup... AIS Setup...
Chapter 10: Navtex 165 To select the message alert categories: Navtex Alert Menu A - Navigational warnings B - Meteorological warnings C - Ice reports D - Search and rescue information E - Meteorological forecasts F - ilot service messages G - Decca messages H - Loran messages I - Omega messages J - Satnav messages K - Other electronic navaid messages L - Additional navigational messages V - Notice to fishermane (US only) W - Environmental (US only) X - Special services Y - Special services Z - No message
166 C-Series Display Reference Manual
Chapter 11: Automatic Identification System (AIS) 167 Chapter 11: Automatic Identification System (AIS) 11.1 Introduction This chapter details the AIS system and how it can be used as a safety aid. Once set up you can overlay the AIS on chart or radar windows and use it to: • Display a target (with heading/speed vectors and rate of turn) for any other AIS equipped vessels. • Display basic or detailed information for each target vessel including safety critical target data.
168 C-Series Display Reference Manual Data details Class A Class B (Sends and receives) (receives only) Static Data Ship's name Type Call sign IMO number Length and beam Antenna loctation Voyage Related Data Draft Cargo information Destination ETA Other relevant information Dynamic Data Time Ship's position COG SOG Gyro heading Rate of turn Navigational status Dynamic Reports Ship's speed Ship's status Safety Note: To change the specified AIS targets and range see page 173.
Chapter 11: Automatic Identification System (AIS) 169 11.3 What do I need to run AIS? In order to run AIS, you will need: • A receive only unit or a full transponder. Note: A receiver will allow you to receive data about other vessels in your area but will not allow other vessels to ‘see’ you. A full transponder transmits and receives AIS data and therefore allows you to receive data about other vessels and for other AIS equipped vessels to see and receive information about your vessel.
170 C-Series Display Reference Manual 11.5 How is AIS data displayed? Heading Large vessel Direction of turn Small vessel Sleeping target 097°T 11.6kt 1.237nm 00h04m33s COG/SOG vector Safe zone (defined by distance or time) Dangerous target (flashes) D9056_1 Safety critical data The AIS system displays other AIS equipped vessels in the surrounding area as triangular targets overlaid on a chart or radar window. Up to 100 targets are displayed.
Chapter 11: Automatic Identification System (AIS) 171 Viewing target information You can display information relating to individual AIS targets. When a target is highlighted with the cursor. The soft keys change to allow you to select the following options: • AIS vectors. • AIS safety critical data. • AIS List. • Full AIS data.
172 C-Series Display Reference Manual AIS List D9092_1 You can also view a list of AIS targets. The list provides collision avoidance data for the highlighted target: AIS OPTIONS... TARGET TRACKING... AIS LIST D9091_1 To display the AIS List: Viewing full AIS data To display detailed AIS data for an individual target e.g. static and dynamic and voyage related data: Move cursor over required target Select required target on AIS list VIEW FULL AIS DATA...
Chapter 11: Automatic Identification System (AIS) 173 11.6 Using AIS for collision avoidance You can use your AIS for collision avoidance by using the safe zone and safety message functions. Safe zones What is a safe zone? A safe zone is a ring centred on your boat within which a target is considered dangerous. It is displayed on radar or chart windows as a red ring.
174 C-Series Display Reference Manual MARPA and AIS options Parameter Options (Default in bold) Vector Length The time period specified for drawing length of vectors. 0.5min, 1 min, 3 min, 6min, 12min, 30 min, 60 min Target History Plots a MARPA target’s previous position at specified intervals. The four most recent position points are displayed. If True target vectors are selected, the four most recent vessel position points are also displayed.
Chapter 11: Automatic Identification System (AIS) 175 Local AIS alarms When the connected AIS unit generates an alarm, your C-Series displays a local alarm message and indicates the alarm status in the data bar icon: AIS Alarm active icon 4nm North-Up (Relative Motion) Local AIS Local Alarm AIS message "AIS message" REMOVE MESSAGE VIEW AIS ALARM LIST... D8968_1 This alarm must be acknowledged on your AIS Receiver. To remove this message press REMOVE MESSAGE. To proceed: 1.
176 C-Series Display Reference Manual 11.8 Simulator We recommend that you use the simulator to familiarize yourself with the AIS function. When the system simulator is switched on (see page 184), it displays 20 AIS targets within a 25nm range. These targets are displayed using the appropriate AIS targets status symbol (see page 170) and move around the screen as if they were real targets. Important: Incoming safety messages cannot be displayed while the simulator is switched on. 11.
Chapter 12: System setup and customizing 177 Chapter 12: System setup and customizing This chapter describes how to setup and customize your C-Series display. Any settings that you change will be stored by the display and shown each time you power on. You can, of course change these settings as many times as you wish. 12.1 Customizing the page sets Each page set provides access to 5 different pages. Each page can display up to four application windows.
178 C-Series Display Reference Manual 2. Edit the page set: Edit Page Set Soft keys display pages within selected page set D8668_1 OK Follow the on-screen instructions The page, window and application layout that you have defined will now be available each time you open the Select Page Set screen. If you do not want to use all 5 pages in a page set, you can switch off individual pages. When you use PAGE to cycle through the pages, the system will now skip any pages that are set to OFF.
Chapter 12: System setup and customizing 179 12.2 Changing the databar You can change the data bar to meet your own particular needs. This includes: • Position - top or side. • Size (top position only). • Data displayed. Note: The databar configuration is a local setting and will therefore only affect the in- dividual display on which you are working.
180 C-Series Display Reference Manual Large data bar D8274_1 Normal data bar To change the data bar size: DATABAR ON OFF DATA Press and hold Databar Setup Menu Position Top Databar Size Configure... Or Top Large Normal Large OK Setup Highlight Top Databar Size System Setup... Alarm Setup Display Setup.... Databar Setup... Select Page Set...
Chapter 12: System setup and customizing 181 Data groups Data (abbreviations in brackets) ENVIRONMENT Pressure Air temperature (Air Temp) Sea temperature (Sea Temp) Set drift WIND True wind Apparent wind (App Wind) Ground wind TIME AND DATE Local time Local date CURSOR POSITION Cursor position (Csr Pos) TRANSDUCER STATUS Transducer status * Trip log You can view the total distance travelled (Log) and the distance since you last applied a reset (Trip) based on your speed through water (STW).
182 C-Series Display Reference Manual Adding data Once you have selected the configure option (see above), you can add new data: Data Pressure Air Temp Sea Temp Det Drift Highlight required Data Group Highlight required Data Select Data Group Select Data OK Add selected data D8278_1 ADD DATA...
Chapter 12: System setup and customizing 183 12.3 Changing the set up menu options Setup MENU Chart Setup... Cartography Setup GPS Setup... Compass Setup... System Setup... Alarm Setup... Display Setup... Databar Setup... Select Page Set... System Diagnostics... Remove CF Card... D8281_1 Highlight required Setup Menu Select Setup Menu The Setup Menu contains application specific and system-wide menus: Application specific These menus relate to the application for the active window i.e.
184 C-Series Display Reference Manual MENU ITEM Simulator ON - allows operation of display without data from antenna and/or external data sources. Demo - a series of slides with descriptions to demonstrate the various system functions. Bearing Mode Mode of all bearing and heading data displayed. This does not affect how the chart or radar are drawn. MOB Data Type Selects whether position data or dead reckoning displayed on screen.
Chapter 12: System setup and customizing 185 MENU ITEM OPTIONS (Default in bold) System Integration See sub-menu below Waypoint Password Set-up... Allows you to set up a password to protect access to your waypoint and route databases. See page 23.
186 C-Series Display Reference Manual MENU ITEM OPTIONS (Default in bold) Pressure Units Select required pressure unit. Bar Psi Kpa Volume Units Select required volume unit. US Gallons Imp Gallons Litres System Integration Setup Menu MENU ITEM OPTIONS (Default in bold) DSC Message When set to ON, details of distress DSC messages are displayed on screen ON OFF SeaTalk Alarms When set to enabled, all SeaTalk system alarms are received and displayed on the chartplotter.
Chapter 12: System setup and customizing 187 Alarm Setup Menu The Alarm Setup Menu is divided into these sub-menus: • System Alarms Setup. • Navigation Alarms Setup. • Radar Alarms Setup. • Fishfinder Alarms Setup. • AIS Alarms Setup. Note: To silence any alarms, press ACKNOWLEDGE. System Alarms Setup System alarms will sound in all applications. MENU ITEM OPTIONS (Default in bold) Anchor Alarm Switches the anchor alarm on or off.
188 C-Series Display Reference Manual Navigation Alarms Setup Navigation alarms will sound in any application when you are navigating. MENU ITEM OPTIONS (Default in bold) Arrival Alarm Radius The distance from the target waypoint or the closest point of approach to the target waypoint that triggers the arrival alarm to sound. 0.1nm 0.01 - 9.
Chapter 12: System setup and customizing 189 MENU ITEM OPTION (Default in bold) Deep Fish Limit Specifies the upper value for the Fish Alarm Depth LImit 1000ft (0002ft - 5000ft) Shallow Depth Alarm Switches the shallow depth alarm on or off. If a DSM is not connected, this cannot be set. OFF ON Shallow Depth Alarm Value If the Shallow Depth Alarm is set to ON, an alarm is triggered if the depth drops below the value you specify.
190 C-Series Display Reference Manual This screen provides, for each tracked satellite, the satellite number, a graphical signal strength bar, status, azimuth angle and its elevation angle from your vessel. The sky view graphic shows the position of these satellites. Actual mode GPS reporting (No Fix, Fix, D Fix or SD Fix) Mode selected by GPS DIFF GPS ON OFF DIFF SET UP OTHER SET UP RESTART GPS D6809_3 Only available if connected to Raymarine landbased GPS e.g.
Chapter 12: System setup and customizing 191 Selecting the COG/SOG filter The COG/SOG filter should be set to the level appropriate to your boat’s use and to the level of oscillation being experienced by the GPS: • HIGH - for use when trawling or when there is a high level of oscillation. • MEDIUM - for general use • LOW - for use when travelling at speed Compass Setup This option can be used to linearize a Raymarine ST80 active compass or Smart Heading sensor connected on SeaTalk.
192 C-Series Display Reference Manual MENU OPTION OPTIONS (Default in bold) Key beep Controls whether a noise is made when you press a key. OFF ON Text size Controls the size of the text on the screen Small Large Databar Setup This sub-menu accesses the Configure Data Bar Menu - refer to page 179 for full details. Select Page Set This sub-menu accesses the Select Page Sets Menu. For details of how to reconfigure the page sets, please see page 177.
Chapter 13: Maintenance & Troubleshooting 193 Chapter 13: Maintenance & Troubleshooting 13.1 Introduction This chapter provides information on maintaining and troubleshooting your C-Series Display, and also information on how to get assistance from Raymarine. 13.2 Maintenance procedures At regular intervals, carry out the following servicing procedures: • Routine checks. • Cleaning the Display. Do not attempt any other servicing procedures.
194 C-Series Display Reference Manual Cleaning the display CAUTION: Cleaning the display Take care when cleaning the display, to avoid damaging it. (1) Do NOT wipe the display screen with a dry cloth, as this could scratch the screen coating. (2) Do NOT use acid, ammonia based or abrasive products. Regularly clean your Display as follows: 1. Switch off the power to the Display. 2. Wipe the Display with a clean soft cloth.
Chapter 13: Maintenance & Troubleshooting 195 Settings and data reset All data set-up menus, including page sets and the data bar, are reset to the factory default when you apply a settings and data reset. Important: Applying a settings and data reset will remove all waypoints, routes and tracks. Applying a settings and data reset To carry out a settings and data reset: MENU GPS Status... Compass Setup... System Setup...
196 C-Series Display Reference Manual Installation/Display Problem Solution Display does not power up • Check power supply cable is sound and that all connections are tight and free from corrosion. • Check relevant fuses. • Check power source is of the correct voltage and sufficient current. My display switches off • Check power input connection is secure at the rear of the Display(s). • Check power cable for damage or corrosion.
Chapter 13: Maintenance & Troubleshooting 197 Chart Problem Solution Vessel not shown in correct geographical position on Display • Check GPS status (page 189). • Check that the Display is not in Simulator mode (see page 184). • Check the SDGPS setting is switched OFF. • Perform the chart offset operation (see page 91). Display does not show enough chart detail • Check that the chart card for the appropriate area is installed. • Set the Declutter option to OFF (see page 89).
198 C-Series Display Reference Manual Radar Problem Solution ‘No data’ message • Check that cable connecting the scanner to the Display is securely connected and undamaged. ‘Scanner software incompatible’ message • Check software revisions by contacting your local Raymarine dealer. “Invalid scanner software: Version xx.x, Version xx.x required” Incorrect software version installed. Contact your local Raymarine dealer.
Chapter 13: Maintenance & Troubleshooting 199 1. Select the Software Services menu: MENU Setup Radar Setup... System Diagnostics External Interfaces..... Internal Interfaces..... Software Services.... GPS Status System Diagnostics... Remove CF Card... Highlight software services Highlight System Diagnostics menu Select System Diagnostics menu D8665_1 Select software services menu 2.
200 C-Series Display Reference Manual For product repair and service In the unlikely event that your Raymarine unit should develop a problem, contact your authorized Raymarine dealer for assistance. The dealer is best equipped to handle your service requirements and can offer timesaving help in getting your equipment back into normal operation. If repairs cannot be obtained conveniently, product service can be obtained by returning the unit to: Raymarine Inc.
Chapter 13: Maintenance & Troubleshooting 201 For Navionics cartography For questions about cartography, please contact Navionics directly through their web site: www.navionics.com or contact Navionics customer support: Navionics customer support Navionics Italy Via Fondacci, 269 Z.I. Montramito 55054 Massarosa Italy Tel: +39-0584-329111 Fax: +39-0584-962696 sales@navionics.
202 C-Series Display Reference Manual
Appendix A: Specification 203 Appendix A:Specification C70, C80 and C120 LCD Color Displays General Approvals: CE FCC Conforms to essential requirements of 1995/5/EC, 1989/336/EC. Compliant with CFR47 Parts 2 & 80 Size: C70 C80 C120 253 x 175 x 110 mm (9.9 x 6.9 x 4.3 in.) excluding bracket 283 x 210 x 110 mm (11.1 x 8.2 x 4.3 in.) excluding bracket 356 x 264 x 114 mm (14.0 x 10.4 x 4.5 in.) excluding bracket Weight: C70 C80 C120 1.2 kg. (2.6 lbs) 1.8 kg. (3.9 lbs) 3.0 kg. (6.
204 C-Series Display Reference Manual General Connectors 13 pin Radar scanner 4 pin DSM 3 pin SeaTalk 5 pin NMEA 5 pin SeaTalk2/ NMEA2000 3 pin Power Interfaces Pathfinder Radar scanner 1 x DSM receive 1 x SeaTalk, receive and transmit 1 x NMEA0183, receive and transmit 1 x SeaTalk2/ NMEA2000 CompactFlash card slot Waypoints 1000 waypoints entered via cursor, lat/lon, range and bearing from present position or at boat’s position. 16 character name can be assigned.
Appendix A: Specification 205 Radar Features Range Scales (Range Rings) 1/8 (1/16)nm to 72 (12) nm dependant on scanner Performance limited by scanner type and position. Range Ring Accuracy Better than +/- 1.5% of the max. range scale in use, or 22m (72 ft), whichever is the greatest.
206 C-Series Display Reference Manual Chart Features Cartography Navionics Charts on CompactFlash cards Chart of the world built in Chart scaling 1/64nm (if cartographic detail is available to 4000nm Presentation Modes Head up, Course up or North up (selectable True or Magnetic) Relative or True Motion Waypoints 1000 waypoints entered via cursor, lat/lon, range and bearing from present position or at boats position. 16 character name can be assigned.
Appendix A: Specification 207 Data features Panel type 5 panels available. Pre-defined (Navigation, Waypoint, Route, Fishing or Sailing) or user-configured. Data available Vessel position, active waypoint, TTG, VMG - Waypoint, depth, COG SOG, heading, speed, set/drift, trip, log, ground log, ground trip, rudder, local time and date, sea temperature, app wind, true wind, VMG wind, ground wind, XTE, compass, locked heading, waypoint data, pressure, air temperature, sea temperature, local data.
208 C-Series Display Reference Manual SeaTalk Input Depth, SOG, COG, Position, Waypoint number, range/ bearing, TTG, Boat speed, Time, XTE, Heading, Wind, data, Log/Trip, Temperature, MOB and cursor position SeaTalk Output Cursor data, guard zone and navigational data bridged from NMEA SeaTalk2 Input SeaTalk2 Output AIS Receiver To receive or receive and transmit AIS data.
Appendix B: Abbreviations 209 Appendix B: List of Abbreviations AIS Automatic Identification System km Kilometer ALR Alarm kpa Kilo pascals °C Degrees Centigrade KPH Kilometers per hour °F Degrees Farenheit kt Knots amp Amperes ky Kiloyards Auto Automatic l litres CAT Category Lat Latitude CCFL Cold Cathode Fluorescent Lamp Lon Longitude CDI Course Deviation Indicator m Metres COG Course Over Ground Man Manual C-Up Course up orientation MARPA Mini Automatic Radar
210 C-Series Display Reference Manual STN Station TCPA Time to Closest Point of TM True motion TTG Time To Go TVG Time Variable Gain TX Transmit UTC Universal Time Constant VMG Velocity Made Good VRM Variable Range Marker WPT/ Waypoint/Waypoints XTE Cross Track Error
Appendix C 211 Appendix C: List of cursor labels Label Feature Application A/B Ruler line Chart AIS AIS target Chart COG Course Over Ground vector Chart CTR centre of radar Radar FLT Floating EBL/VRM Radar GRD Guard zone Radar HDG Heading vector Chart MARPA MARPA target Radar MOB Man Over Board marker Chart and radar POS Vessel’s position Chart RTE Route leg Chart SHM Ship’s Heading Marker Radar TIDE Tide indicator Chart VRM/EBL VRM and EBL, 1 or 2 Radar WIND
212 C-Series Display Reference Manual
Index Index A Abbreviations, 209, 211 Activated AIS target, 170 Active alarm list, 175 Active window, 15 Advanced setup radar, 149 Air temperature, in data bar, 181 AIS alarms, 174 active, 175 list, 189 local, 174 classes of data, 167 collision avoidance, 172 displaying data, 169 full AIS data, 172 list, 171 menu, 176 options, 173 running, 168 safe zone own vessel, 174 setting up, 173 time to, 174 safe zones, 173 safety critical data, 171 safety messages, 174 safezone ring, 174 selecting, 169 simulator, 17
214 measuring, 135 mode, 184 for EBLs, 130 Blind echoes, 120 sectors, 122 Boat position, 46 symbol, 46 Bottom fill, 104 image, 96 lock, 103 Bridge NMEA heading, 186 Business services, 52 Buttons, 7 C Cancelling alarms, 27 MARPA targets, 147 Cards erasing information from, 21 inserting, 18 removing, 19 retrieving information from, 20 saving information to, 19 Cartography Navionics technical support, 200 setup, 93 show/hide features, 89 Caution and routing data, 94 show/hide, 89 CDI displaying, 158 steering i
Index views, 82 local, 83 multiple, 83 system, 83 waypoint arrival alarm, 75 wind indication, 74 XTE restart, 72, 82 zooming, 46 Circular guard zones, 142 Cleaning, the display, 193 Clearing alarms, 27 MOB, 27 Clutter, 122 COG, 74 in data bar, 180 Collision avoidance, 140 using AIS, 172 using guard zones, 140 using MARPA, 143 using VRMs and EBLs, 138 Color gain, 116 palette, 16, 111 CompactFlash cards, 17 cautions, 17 erasing information, 21 inserting, 18 removing, 19 retrieving information, 20 use of, 17 w
216 Dialog boxes, 9 editing, 11 Digital data application selecting a panel, 151 Display adjust lighting, 16 alarms, 27 application, 8 CDI application, 158 chart application, 45 chart detail, 86 control waypoint display, 41 current details, 50 digital data application, 151 engine monitor application, 159 fishfinder, 111 Fishfinder application, 96 MOB (man overboard), 26 object and feature details, 47 reset, 194 setup cursor autohide, 191 key beep, 192 menu, 191 soft key autohide, 191 text size, 192 show/hide
Index manual, 114 dual mode, 114 single mode, 114 operating, 114 gain controls, 117 auto, 115 manual, 116 interpreting the bottom structure, 96 isolating bottom fish, 104 white line, 104 live image, 98 marking a position, 107 operating frequencies, 114 overview, 95 ping enable/disable, 113 rate limit, 113 power setting, 117 principles, 95 scroll, 111 pausing, 105 speed, 105, 111 setup, 110 display, 111 DSM, 113 transducer, 112 shifting the image, 100 SONAR interference rejection, 113 speed offset, 112 targe
218 Manual gain mode, 116 operating frequency, 114 variation, 184 Marine features, 94 Marine features, 89 MARPA acquiring targets, 147 cancelling targets, 147 collision avoidance, 143 CPA vectors, 145 on chart, 76 operating ranges, 144 overview, 143 risk assessment, 144 setup, 146 symbols, 144 target data, 144 symbols, 144 MARPA options, 173 Measuring bearings, 135 distances, 54, 135 ranges, 135 VRMs, 136 Menus accessing, 10 AIS, 176 alarm setup, 187 fishfinder alarms, 188 navigation alarms, 188 radar alarm
Index Nearest port, 48 port service, 48 tidal station, 48 waypoint, 48 Night operation adjusting the display lighting, 16 NMEA bridge heading, 186 output setup, 186 port setting, 186 North up mode, 84 O Object information, 90 Offset depth, 112 speed, 112 temperature, 112 vessel, 85 Offtrack alarm, 188 Operating frequencies automatic, 114 manual, 114 Orientation chart, 84 course up, 84 head up, 84 north up, 84 radar, 126 Overlay radar on chart, 76 Overview, 1 Own vessel safezone, 146 P Page layout, reconfigu
220 C-Series Display Reference Manual sea clutter, 131 setting gain, 131 tune radar, 131 using gain controls, 130 wakes, 134 guard zones, 140 head up mode, 127 impaired radar performance, 120 blind sectors, 122 indirect echoes, 121 multiple echoes, 122 rain clutter, 123 sea clutter, 122 side lobes, 121 interference, 123 rejection, 133 introduction, 119 MARP A, 143 MARPA CPA vectors, 145 relative, 146 true, 145 on chart, 76 operating ranges, 144 overview, 143 target data, 144 symbols, 144 maximum range, 120
Index edit, 68, 81 change color, 73, 82 change course, 69 change name, 73, 82 erasing, 73, 82 follow, 63 overview, 58 reversing, 69 selecting, 68 viewing details, 66 Rudder, in data bar, 180 Ruler, 54 clearing, 55 repositioning, 55 S Safe zone AIS, 173 own vessel, 146, 174 ring, 146, 174 time to, 146, 174 Safety, 193 AIS messages, 174 Safety contours, 93 Safety critical AIS data, 171 Safezone ring, 174 Saving information to a card, 19 Scanner operating modes, 123 Scroll, 111 pause, 105 speed, 105, 111 Sea c
222 Spot soundings, 93 show/hide, 89 ST290 system, 186 Standby, 149 Status bar, 9, 45 icons, 9, 12, 169 Steering, using CDI, 157 Symbols AIS targets, 170 boat, 46 business services, 52 MARPA, 144 navigation marks, 94 port, 51 waypoint, 87 waypoints, 29 Synchronizing chart with radar range, 76 System alarms setup, 187 integration, 185 setup menu, 186 setup menu, 183 System diagnostics, 192 T Target acquiring, 147 activated, 170 AIS symbols, 170 cancelling, 147 dangerous, 170 dangerous alarm, 173 depth, 108,
Index Units measurement, 13 setup menu, 184, 185 depth, 185 distance, 185 measurement, 13 pressure, 186 speed, 185 temperature, 185 volume, 186 V Variation source, 184 Vectors AIS, 171 CPA, 145 length, 90, 146 using chart vectors, 74 Vessel offset, 85, 129 position, in data bar, 180 symbol, 46 Viewing chart, 45 MARPA targets, 76 windows, 82 route details, 66 waypoint information, 33 VMG Wind/Waypoint, in data bar, 180 VRMs, 108 floating, 138 measuring with, 136 unfloating, 140 using with fishfinder, 109 usi
224 C-Series Display Reference Manual Window active, 15 selecting, 14 X XTE in data bar, 180 resetting, 57 restart, 72, 82 Z Zoom Chart, 46 Fishfinder, 102 position, 102 Radar, 135
i Raymarine World Wide Warranty Raymarine Inc. APPLICABLE TO PRODUCTS SOLD THROUGH OFFICIAL RAYMARINE INC. DEALERS, DISTRIBUTORS AND BOAT BUILDERS WITHIN THE AMERICAS AND CARIBBEAN. Limited warranty Subject to the terms, conditions and limitations set forth in this U.S.
ii Raymarine World Wide Warranty Limitations and Exclusions In addition to any other limitations and exclusions set forth herein, Raymarine is not responsible for, and this Warranty does not cover: • • • • • • • failures due to abuse, misuse, accident, unauthorized alteration or repair, improper installation (whether or not by a Raymarine-certified service agent), shipping damage or corrosion; Costs associated with routine system checkouts, alignment/calibration, seatrials or commissioning; repair or rep
iii Raymarine UK Ltd. APPLICABLE TO PRODUCT SOLD THROUGH OFFICIAL RAYMARINE UK LTD. DEALERS, DISTRIBUTORS AND BOAT BUILDERS WITHIN EUROPE, THE MIDDLE AND FAR EAST, AFRICA AND AUSTRALASIA. Limited Warranty The Raymarine warranty terms and conditions as described below do not affect the customers legal rights and complies with EU Directive 1999/44/EC.
iv Raymarine World Wide Warranty 3.2 In cases where the customer is requesting a warranty service and a Raymarine certified installer has not installed the product; i.e. Product warranty, the affected product must be returned to the customer’s local Raymarine approved service agent or direct to Raymarine with: 3.2.1 proof of purchase showing the date of purchase and the name of the supplier of the product; and 3.2.2 the serial number of the affected product; or 3.2.
v 4.11 The Raymarine warranty does not cover any differences in material, coloring or size between those alluded to in corporate advertising, literature or published on the internet, which are not specifically objected to at the time of delivery. 4.12 Travel costs other than auto mileage, tolls and two (2) hours travel time, are specifically excluded from the warranty on all products.
vi Raymarine World Wide Warranty Raymarine Service Centers North and South America Europe, Middle East, Africa and Australasia Raymarine Technical Support 1-800-539-5539 or, +1 603-881-5200 Raymarine Technical Support +44 (0) 23 9271 4713 Product Repair and Service Raymarine Product Repair Center 21 Manchester Street, Merrimack, NH 03054-4801 USA Product Repair and Service Raymarine plc Anchorage Park Portsmouth PO3 5TD England Help us to help you To allow us to respond to your needs faster, please
