87020-3.
87020-3.book Page ii Tuesday, March 7, 2006 11:02 AM Trademarks and registered trademarks Autohelm, HSB, Raymarine, RayTech, RayTech Navigator, Sail Pilot, SeaTalk and Sportpilot are registered trademarks of Raymarine Limited. Apelco is a registered trademark of Raymarine Holdings Limited (Registered in all major marketing territories).
87020-3.book Page i Tuesday, March 7, 2006 11:02 AM Important Information i Important Information Intended use This handbook provides information and instructions to assist in planning and installing your Raymarine C-Series Display, together with information that will be useful when you are connecting the C-Series Display to other equipment. In order to obtain the best results in operation and performance, please read this handbook thoroughly.
87020-3.book Page ii Tuesday, March 7, 2006 11:02 AM ii C-Series Displays Installation Manual CAUTION: Radar Scanners, Cables & Installation Information on radar scanners, cables and their installation contained in this handbook supersedes that contained in the Pathfinder Radar Scanner Handbook, Document No. 81154_8, dated 12th January 2005.
87020-3.book Page iii Tuesday, March 7, 2006 11:02 AM Important Information iii Handbook information To the best of our knowledge, the information in this handbook was correct when it went to press. However, Raymarine cannot accept liability for an inaccuracies or omissions it may contain. In addition, our policy of continuous product improvement may change specifications without notice. Therefore Raymarine cannot accept liability for any differences between the product and the handbook.
87020-3.
87020-3.book Page 1 Tuesday, March 7, 2006 11:02 AM Contents 1 Contents Chapter 1: Preparation for installation ..................................................................5 1.1 General information ............................................................................................. 5 Contents of this pack ....................................................................................... 5 Dimensions ....................................................................................
7020-3.book Page 2 Tuesday, March 7, 2006 11:02 AM 2 C-Series Displays Installation Manual Chapter 3: Installation .............................................................................................21 3.1 Introduction ........................................................................................................21 3.2 Mounting the display ..........................................................................................21 Trunnion mount ......................................
87020-3.book Page 3 Tuesday, March 7, 2006 11:02 AM Contents 3 4.5 Advanced Settings ..............................................................................................43 Adjusting the settings ...................................................................................43 Display timing .........................................................................................44 Chapter 5: Troubleshooting ...................................................................................
87020-3.
87020-3.book Page 5 Tuesday, March 7, 2006 11:02 AM Chapter 1: Preparation for installation 5 Chapter 1: Preparation for installation 1.1 General information Contents of this pack The C-Series (C70, C80 or C120) Display pack contains the following items: Item Quantity Part No.
87020-3.book Page 6 Tuesday, March 7, 2006 11:02 AM 6 C-Series Displays Installation Manual Dimensions The dimensions for your C-Series display are: C70 Display PAGE 177 mm (6.96 in) WPTS MOB DATA MENU OUT RANGE IN OK 189 mm (7.44 in) ACTIVE CANCEL 9.5 mm (0.375 in) 253 mm (10 in) 89.4 mm (3.5 in) 282 mm (11.1 in) 220 mm (8.66 in) plug clearance D6612-1 C80 Display PAGE ACTIVE MENU OUT RANGE IN OK 222 mm (8.75 in) DATA 212.5 mm (8.4 in) WPTS MOB CANCEL 9.5 mm (0.375 in) 283 mm (11.
87020-3.book Page 7 Tuesday, March 7, 2006 11:02 AM Chapter 1: Preparation for installation 7 C120 Display PAGE ACTIVE MENU OUT RANGE IN OK 267 mm (10.5 in) DATA 276.66 mm (10.9 in) WPTS MOB CANCEL 9.5 mm (0.375 in) 357 mm (14 in) 385 mm (15.15 in) 87.9 mm (3.46 in) 220 mm (8.66 in) plug clearance D6611-1 Accessories and spares Raymarine accessories and parts can be obtained from your authorized Raymarine dealer.
87020-3.book Page 8 Tuesday, March 7, 2006 11:02 AM 8 C-Series Displays Installation Manual 1.2 Planning the installation This section provides information and advice for planning the installation of your Display. EMC Installation Guidelines All Raymarine equipment and accessories are designed to the best industry standards for use in the recreational marine environment.
87020-3.book Page 9 Tuesday, March 7, 2006 11:02 AM Chapter 1: Preparation for installation 9 Suppression Ferrites The illustration shows typical cable suppression ferrites used with Raymarine equipment. Always use the ferrites supplied by Raymarine. D6626-1 Connections to other equipment If your Raymarine equipment is to be connected to other equipment using a cable not supplied by Raymarine, a suppression ferrite MUST always be attached to the cable near to the Raymarine unit.
87020-3.
87020-3.book Page 11 Tuesday, March 7, 2006 11:02 AM Chapter 2: System Integration 11 Chapter 2: System Integration 2.1 Introduction This chapter provides an overview of system integration, you may find that your system does not use all the protocols or contain all the instrumentation that is described in it. However it is hoped that the information supplied will help in your understanding of how systems can be integrated and used successfully. 2.
87020-3.book Page 12 Tuesday, March 7, 2006 11:02 AM 12 C-Series Displays Installation Manual What is NMEA? NMEA 0183 The NMEA 0183 Data Interface Standard was developed by the National Marine Electronics Association of America. It is an international standard to enable equipment from many different manufacturers to be connected together and share information. The NMEA 0183 standard carries similar information to SeaTalk.
87020-3.
87020-3.book Page 14 Tuesday, March 7, 2006 11:02 AM 14 C-Series Displays Installation Manual Alternatively, in North America call Navionics toll-free on 1-800-848-5896. Outside of North America, contact your local dealer or call Navionics SpA on tel: (+39) 0584 961696 or fax: (+39) 0584 961309. CompactFlash cards It is possible to archive or transfer information to and from your C-Series display and other compatible instruments using CompactFlash cards.
87020-3.book Page 15 Tuesday, March 7, 2006 11:02 AM Chapter 2: System Integration 15 (2) Engine output from a compatible engine manufacturer is also required. See Raymarine.com for latest compatibility information. (3) Whilst an AIS receiver is not required for the radar and chart applications to function, this receiver is necessary if AIS functionality is required within radar and chart.
87020-3.book Page 16 Tuesday, March 7, 2006 11:02 AM 16 C-Series Displays Installation Manual 2.5 How is the C-Series display integrated? The diagrams that follow show some suggested set ups. These are not however the only possible combinations.
87020-3.
87020-3.
87020-3.
87020-3.
87020-3.book Page 21 Tuesday, March 7, 2006 11:02 AM Chapter 3: Installation 21 Chapter 3: Installation CAUTION: Preparation Please ensure that you have read ‘Preparation for Installation before proceeding. CAUTION: Radar Scanners, Cables & Installation Information on radar scanners, cables and their installation contained in this handbook supersedes that contained in the Pathfinder Radar Scanner Handbook, Document No. 81154_8, dated 12th January 2005. 3.
87020-3.book Page 22 Tuesday, March 7, 2006 11:02 AM 22 C-Series Displays Installation Manual D6739_1 6. Locate the bezel over the front of the display. See “Attaching the front bezel” on page 24. 7. Check that the buttons have passed through the bezel and are free to operate. It is suggested that you use your thumb or forefinger in a circular motion to do this. 8. Adjust the unit to the required angle for clear vision, and tighten the trunnion knobs.
87020-3.book Page 23 Tuesday, March 7, 2006 11:02 AM Chapter 3: Installation 23 3. Using a suitable hole saw (the size is indicated on the template), make a pilot hole in each corner of the cut-out area. D6738_1 4. Using a suitable saw, cut along the inside edge of the cut-out line. 5. Ensure that the unit fits into the removed area and then file around the cut edge until smooth. 6. Remove the mounting bracket knobs and the mounting bracket from the display unit. 7. Drill four 4.
87020-3.book Page 24 Tuesday, March 7, 2006 11:02 AM 24 C-Series Displays Installation Manual Fixing bolts When console mounting your C-Series Display, avoid damaging the rear trim ring by using the correct length bolts.
87020-3.book Page 25 Tuesday, March 7, 2006 11:02 AM Chapter 3: Installation 25 2. Place the bezel over the front of the C-Series Display, ensuring that locking lugs located at the bottom edge of the bezel are latched into position. 3. Ensure that the control buttons pass through their respective openings. 4. Apply firm but even pressure to the bezel along the: • Outer edges - work from the sides upwards and then along the top edge, to ensure that it clips securely into position.
87020-3.book Page 26 Tuesday, March 7, 2006 11:02 AM 26 C-Series Displays Installation Manual 3. Working from this corner, free the clips along the top edge of the display, then work towards the bottom edge. Taking care to ensure that the control buttons pass through the bezel. DO NOT lever along the top edge. 4. Carefully free the locating clips at the bottom of the bezel by lowering it away from the unit - DO NOT USE A SCREWDRIVER FOR THIS AS IT WILL DAMAGE THE CLIPS. 5.
87020-3.book Page 27 Tuesday, March 7, 2006 11:02 AM Chapter 3: Installation 27 C-Series cable connections Seatalk/Alarm out (2m) R G Digital Sounder Module (DSM) Y DSM SEATALK SEATALK 2 SeaTalk2 IN / OUT NMEA RADAR POWER Power (1.5m) Not supplied/accessory NMEA (1.5m) D6614-2 Supplied Using cable splicers The cable splicers are used to make the connections from the SeaTalk/Alarm out and NMEA 0183 cables easy and secure, without removing insulation from cable tails.
87020-3.book Page 28 Tuesday, March 7, 2006 11:02 AM 28 C-Series Displays Installation Manual 1. Place the wires to be joined into the connectors, ensuring correct polarity and that the wires are pushed fully home. 2. Using a pair of pliers, crimp the connector bulb together. 3. Check that a secure connection has been made. 4. Ensure that the cables are secured in a suitable position to prevent the join being placed under strain.
87020-3.book Page 29 Tuesday, March 7, 2006 11:02 AM Chapter 3: Installation 29 Fuse, circuit breaker and switch ratings Radar scanner? No Yes Device Rating with fuse 6.3 amp anti-surge fuse with isolator switch 10amp with thermal circuit breaker 5 amp Refer to the fuse notification in the scanner handbook. SeaTalk cable The SeaTalk cable is supplied with stripped tails.
87020-3.book Page 30 Tuesday, March 7, 2006 11:02 AM 30 C-Series Displays Installation Manual Fishfinder cable The fishfinder cable is supplied with your Digital Sounder Module (DSM). This cable should be run and connected to the rear of the display.
87020-3.book Page 31 Tuesday, March 7, 2006 11:02 AM Chapter 3: Installation 31 If the existing cable is too short, please order from the following: Part No.
87020-3.book Page 32 Tuesday, March 7, 2006 11:02 AM 32 C-Series Displays Installation Manual Connect to C-Series display Red (12/24V) Black (0V) Green (ground) Cable splitter Connect to boat's DC power supply Connect to open array scanner cable D6620-2 The split pedestal cables are available from your local Raymarine dealer as follows: Part No Description E05017 25m Split pedestal cable E05018 15m Split pedestal cable E05019 Pedestal adaptor cable ...
87020-3.book Page 33 Tuesday, March 7, 2006 11:02 AM Chapter 3: Installation 33 Split pedestal cable To display To Open Array Scanner To power Note: You should ensure that the distance (cable route) from the power supply to the open array is kept to a minimum.
87020-3.
87020-3.book Page 35 Tuesday, March 7, 2006 11:02 AM Chapter 4: Commissioning the system 35 Chapter 4: Commissioning the system 4.1 Introduction This chapter details the commissioning of your C-Series Display and includes the following: • Required input. • Pre-start checks. • Initial power on procedure • Radar checks and alignment. • Chart application checks. • Fishfinder checks. • AIS. • Navtex. 4.
87020-3.book Page 36 Tuesday, March 7, 2006 11:02 AM 36 C-Series Displays Installation Manual GPS Check that the GPS has a clear view of the sky and is not obstructed e.g. by buildings, bridges or other equipment fitted on-board. Other equipment For details of pre-start checks for other equipment e.g. AIS and Navtex receivers, please refer to the relevant handbook. 4.3 Initial power on procedure Once you have conducted the pre-start checks you are ready to start the display: D6577-1 1.
87020-3.book Page 37 Tuesday, March 7, 2006 11:02 AM Chapter 4: Commissioning the system 37 4.4 Tests and checks Test and align the radar Your C-Series display is part of an integrated system. Raymarine strongly advise that you test and align the radar before connecting to other systems. To test and align the radar you must first select a radar application. With the Select Page Set screen displayed (see previous section): 1. Press OK to select the highlighted page set. 2. Press PAGE.
87020-3.book Page 38 Tuesday, March 7, 2006 11:02 AM 38 C-Series Displays Installation Manual Radar alignment checks You should check the bearing and display timing alignment to ensure that an accurate picture is shown. Bearing alignment Adjusting the bearing alignment ensures that targets appear at the correct bearing relative to your boat’s bow.
87020-3.book Page 39 Tuesday, March 7, 2006 11:02 AM Chapter 4: Commissioning the system 39 Adjusting the bearing alignment 1. If moored, move the EBL to calculate bearing. 2. With a radar application in the active, press MENU. The Set Up menu is displayed. 3. With RADAR SET UP highlighted, use the trackpad (right) to display the RADAR SET UP menu. 4. Use the trackpad (up/down) to highlight and then the trackpad (right) to select BEARING ALIGNMENT.
87020-3.book Page 40 Tuesday, March 7, 2006 11:02 AM 40 C-Series Displays Installation Manual This screen provides, for each tracked satellite, the satellite number, a graphical signal strength bar, status, azimuth angle and its elevation angle from your vessel. The sky view graphic shows the position of these satellites. Positional accuracy is dependent upon these parameters; in particular, the azimuth and elevation angles are used in a triangulation process to calculate your position.
87020-3.book Page 41 Tuesday, March 7, 2006 11:02 AM Chapter 4: Commissioning the system 41 3. Zoom out with the RANGE button until the world map is visible. 4. To ensure that the display is responding to position data: i. Press FIND SHIP. ii. Check that the cursor is positioned over the boat symbol in the centre of the display. 5. Insert a chart card containing a suitable chart for the area in which you are located. Once inserted, the chart should redraw with the cartridge chart boundaries displayed.
87020-3.book Page 42 Tuesday, March 7, 2006 11:02 AM 42 C-Series Displays Installation Manual Connecting equipment to the NMEA port Connected equipment to NMEA port Setting Additional information General NMEA instruments NMEA 4800 Default setting Navtex receiver Navtex 4800 Navtex 9600 Please refer to your Navtex receiver manual for details of the appropriate setting.
87020-3.book Page 43 Tuesday, March 7, 2006 11:02 AM Chapter 4: Commissioning the system 43 AIS unit not available i.e. not connected or off. AIS unit switched on and operating. AIS unit switched on and operating but dangerous & lost target alarm disabled. D9014_1 AIS unit on with active alarm. 4.
87020-3.book Page 44 Tuesday, March 7, 2006 11:02 AM 44 C-Series Displays Installation Manual Display timing The display timing can be affected by the length of cable used to connect the scanner to your C-Series display. This will in turn affect the short range accuracy of the radar. A symptom of incorrect timing is that bridges or piers shown on the picture appear to be bowed i.e. Own ship Timing early Own ship Timing late Own ship Normal D6625-2 To check the display timing: 1.
87020-3.book Page 45 Tuesday, March 7, 2006 11:02 AM Chapter 5: Troubleshooting 45 Chapter 5: Troubleshooting Introduction This chapter provides information on troubleshooting your Raymarine C-Series Display at installation, and how to get assistance from Raymarine. 5.1 How can I troubleshoot my Display? All Raymarine products are, prior to packing and shipping, subjected to comprehensive test and quality assurance programs.
87020-3.book Page 46 Tuesday, March 7, 2006 11:02 AM 46 C-Series Displays Installation Manual 5.2 Technical Support Raymarine provides a comprehensive customer support service, on the world wide web, through our worldwide dealer network and by telephone help line. If you are unable to resolve a problem, please use any of these facilities to obtain additional help. World wide web Please visit the Customer Support area of our website at: www.raymarine.
87020-3.book Page 47 Tuesday, March 7, 2006 11:02 AM Chapter 5: Troubleshooting 47 Contacting Raymarine in the US You can contact Raymarine in the US either using the Raymarine world wide web as detailed above or by calling one of the telephone numbers below. Accessories and parts You can obtain many Raymarine accessories and parts directly from your authorized Raymarine dealer.
87020-3.
