User's Manual

Atlas PT Technical Manual
17
ATPC
Read TX Current. Read the device’s current draw during the
last transmission, in mA.
0-9999
-
ATRQ
Receiver Signal Level – Reads the Receiver Signal strength
this instant, and returns the level in dBm.
Range: -40 to –130 (dBm)
-
ATRS
RSSI (Receive Signal Strength Indicator) – Returns the
signal level of last received packet. The reading is in dBm.
Usable for relative comparison of signals, but absolute value
is within10dB at -90dBm.
No parameters. Returns a
number: -50 to –140
(dBm) varies by model.
none
ATRV
Disable Remote Access – When enabled (set to a 0), the
modem will respond to over-the-air RPR requests, Pings, and
over-the-air commands. Default is OFF (1).
0= Remote Access on
1=Remote Access off
1
ATSL
Serial Number – Reads and returns a unique serial number
for this unit.
Read Only
1 - 999999999
unique
ATSH
Show – Display the configuration of the modem. This will
return a page of ASCII characters, showing the main
configuration parameters.
none
None
ATSM
Power Savings Options – When set to 0, the internal radio
receiver will be ON. When set to 4 (default for the Atlas
SM), the internal radio receiver will always be OFF and the
radio will not receive over-the-air messages.
Range: 0, 1, 2, 3, 4, 5
4
(RX OFF)
ATST
Statistics – Show the unit’s operational statistics. See
Statistics section of user manual.
0, 1,2, 3, 4, or 5
None
ATTE
Read product temperature – Read the internal temperature
of the unit’s circuit board in degrees Celsius.
-40 to +99
-
ATTT
Max Packet Size – Set the maximum number of bytes in an
over-the-air packet.
1 - 512
80
ATVB
Read DC input Voltage– Returns the DC input voltage
reading, in mV (12500 = 12.5VDC input).
None
none
ATVR
Firmware Version – Returns firmware version currently
loaded on the module.
Read Only, 3 characters
none
ATXn
Show or Configure the Repeat Table – Set the addresses
that this unit will store-and-forward data to/from. n = 1, 2, 3, or
4 designating the entry in the table to show or edit..
Four parameters
aaaabbbbccccdddd where
aaaa=Source Address
bbbb = S.A. Mask
cccc = Destination Address
dddd = D.A. Mask
ATXR
Enable/Disable Store and Forward Repeating – 0=disabled,
1 – enabled.
0 or 1
0 (Off)
ATHX
Enable/Disable single-hop repeating – 0=any number of
repeats, 1 – unit will not repeat a packet that was already
repeated.
0 or 1
0 (multi-hop
OK)
AT&F
Restore Factory – Restore the factory default values. This
command will not erase the calibration values.
none
PING
Ping another modem. Format is PING xxxx, where xxxx is
the ID of the modem to ping. If remote access is enabled on
xxxx, it will respond.
XXXX
-
RPR
Remote Procedure Request. Used to request execution of a
command on a remote mode (over the air). See RV-M7
System Protocol manual for information on using this feature.
SHOW
Show/display an overview of the radio’s configuration.
None
-
BAND
Show/display the radio band. Displays the frequency band
that the radio is configured for, along with the upper and lower
frequency, in MHz. BB is the band code, lll is the lower
frequency in MHz, and uuu is the upper frequency in MHz.
None
BB, lll, uuu
CONFIG
Show Configuration. Display the settings of every parameter
in the unit. If the parameter is 1, then the help text is not
displayed, If the parameter is 2, the configuration is output in
None, 1, 2
-