Technical Manual “RAPID” RDS System Rev.
Technical Manual “RAPID” RDS System Ver. 2 of 28/05/2012 Page 3 INDEX - RAPID DESCRIPTION DISPLAY..................................................................................PAGE 4 - USER MENU FOR SERIES AIR...................................................................................PAGE 5 - USER MENU FOR SERIES FLOW...............................................................................PAGE 6 - USER MENU FOR SERIES HYDRO..................................................
Ver.
us Ver.
Ver.
Ver. 2 of 28/05/2012 Technical Manual “RAPID” RDS System Page 7 USER MENU FOR HYDRO SERIES OK P2 P1 STOVE STATUS OK SET AMBIENT OK SET POWER OK OK P2 P2 P1 P2 OK P2 P1 P2 OK STOPWATCH P1 P2 OK P1 P2 OK P1 SET WINTER/SUMMER OK ON - OFF P2 P1 OK SET POT.
1 2 3 4 4 ON / PRE-HEATING DELAY FLAME THIS FLAME WORK AIR MODULATION FAN – START DELAY TF15/TF45 if T. SMOKE < TF07 after RESTART BLOCKAGE 7 4 4 AIR MODULATION with display of "AIR FLOW METER FAILURE 09." WORK With RDS disabled After switching by OK Flow meter failure or disconnection if Amb. T. > SET Amb. T. with CLIMATE COMFORT active if T. SMOKE> TF15 & T. SMOKE < TF07 After RESTART BLOCKAGE.
Technical Manual “RAPID” RDS System Ver.
Technical Manual “RAPID” RDS System Ver.
Technical Manual “RAPID” RDS System Ver. 2 of 28/05/2012 Page 11 Unit: ALTITUDE TF TF38 NAME ALTITUDE DESCRIPTION Altitude above sea level UNIT ' t/min Unit: ON / OFF air flow meter TF TF39 NAME AIR FLOW METER ON / OFF DESCRIPTION "OFF" disables the RDS.
Technical Manual “RAPID” RDS System Ver.
Technical Manual “RAPID” RDS System Ver. 2 of 28/05/2012 Page 13 Unit: EXTRACTOR SPEED TF NAME DESCRIPTION UNIT ' TF33 MOD. SMOKE P SPEED. Smoke suction speed in the work phase at MODULE power g/min TF34 MIN SMOKE P SPEED. Smoke suction speed in the work phase at MINIMUM power g/min TF35 MAX SMOKE P SPEED.
Technical Manual “RAPID” RDS System Ver. 2 of 28/05/2012 Page 14 RDS SYSTEM ADJUSTMENT PROCEDURE This particular RDS adjustment method allows for the calibration of the parameters related to the oxygen intake for combustion in a more or less automatic manner. A detail of the new firmware is the presence of the “Regular sist.
Technical Manual “RAPID” RDS System Ver. 2 of 28/05/2012 Page 15 ALARMS Code 02 03 05 06 01 08 DISPLAY SMOKE PROBE SMOKE TEMPERATURE FAILURE TO LIGHT PELLETS FINISHED BLACK-OUT DEPRESSURIZATION MOTIVATION RESOLUTION Smoke probe either disconnected or unserviceable. - verify exact reading of the probe in STOVE STATUS; - check cabling; - change the smoke probe. High smoke temperature (over 289°C) The words HOT SMOKE only indicates a pre-alarm.
Ver. 2 of 28/05/2012 Technical Manual “RAPID” RDS System Code DISPLAY MOTIVATION 09 AIR FLOW FAILURE 15 SCREW PUMP TRIAC 14 Page 16 RESOLUTION The air flow meter does not properly read the flow rate. - Check cable connection of air flow meter; - Check for defects of the air flow meter (check STOVE STATUS if the delta of the flow meter temperatures are not greater than 30°C) The electronic component that manages of the screw pump ON/ OFF is damaged.
Ver.
Technical Manual “RAPID” RDS System Ver. 2 of 28/05/2012 Page 18 TROUBLESHOOTING Code 05 DOES NOT TURN ON PELLET DOES NOT DROP DOWN GEAR MOTOR FAILURE Verify its operation by connecting it directly to the 220V.
Technical Manual “RAPID” RDS System Ver.
Technical Manual “RAPID” RDS System Ver.
Technical Manual “RAPID” RDS System Ver. 2 of 28/05/2012 Page 21 Code 03 TEMPERATURE SMOKE STOVE IS OFF Low extractor speed or pellet load excessive Check specific parameters of screw pump and extractor speed Smoke Sensor too deeply inserted Move smoke Sensor Smoke loop clogged Clean this goes EXCHANGER MALFUNCTIONING or BROKEN Directly connect to the 220v and in the event of replacing the exchanger Insufficient exchange of the machine body (e.g.
Technical Manual “RAPID” RDS System Ver.
Technical Manual “RAPID” RDS System Ver. 2 of 28/05/2012 Page 23 Code 16 PRESSURE CONNECTOR NOT INSERTED IN pressure Lack of pressure or excessive BOARDinside the hydraulic circuit NB: Check in STOVE STATUS the pressure in the circuit, being especially careful about the proper dimensioning of the expansion vessel Pressure under 0.5 BAR Fill the tank circuit up to 1.2 bar cold PRESSURE OVER 2.
Technical Manual “RAPID” RDS System Notes: Ver.
Ravelli srl Via Kupfer, 31 - 25036 Palazzolo sull’Oglio / BS - ITALY Tel. +39 030-7402939 Fax +39 030-7301758 Internet: www.ravelligroup.it E-mail : info@ravelligroup.
