User`s guide

eSATA ExpressCard/34
EX30S
User's Guide
1
2
3
4
5
6
Introduction * * * 2
-1. Package Contents * * * 2
-2. Layout * * * 2
-3. System Requirements * * * 3
-4. Specifications * * * 3
-5. Caution * * * 4
Setup * * * 5
-1.
Installation on Windows System
* * * 5
-2.
To Verify Driver Installation (Windows)
* * * 7
-3. Hot-plug tool (Windows) * * * 8
-4. Installation on Mac system * * *10
Connecting/Removing eSATA drive * * *11
-1. Windows * * *11
-2. Mac * * *15
Removing ExpressCard * * *16
-1. How to remove EX30S on Windows * * *16
-2. How to remove EX30S on Mac * * *16
Registration & Tech-Support * * *17
-1. Registration * * *17
-2. Tech-Support * * *17
Appendix * * *18
Contents
-1. Package Contents
Introduction
1
1
-2. Layout
1
eSATA Connector
ExpressCard Connector
Support Port Multiplier)
-3. System Requirements
1
-4. Specification
1
What's Port Multiplier(PM)?
?
.......
-5. Caution
1
Setup
2
-1. Installation on Windows system
2
8
Found New Hardware Wizard
No, not at this time
Next
Install the software automatically(Recommended)
Next
Finish
Windows XP, Server 2003
Silicon Image
SiI
3132 SATALink Controller
-2. To Verify Driver Installation
2
Silicon Image
SiI
3132 SATA
Link Controller
What's HotPlug Tool
What's HotPlug Tool
Insert software CD-ROM.
HotPlug Tool allows to remove the eSATA drive connected to the EX30S
without the system shut down. If the eSATA drive needs to be removed from
the EX30S before shut down, install the HotPlug Tool.
1.
Open the CD-ROM and click HotPlugTool folder.
Double click on SetupHotPlugTool.exe.
* File extension(.exe) may
not be shown.
2.
Installer will be launched. Follow
the instructions.
3.
4.
-3. HotPlug Tool (Windows)
-3. HotPlug Tool (Windows)
2
Add or Remove Programs Control Panel
HotPlugTool Change or Remove Programs
OK
Start Program Hot plug tool
[A] Removing eSATA drive
Stop
[B] Change HotPlug Tool setting
HotPlug Tool Window
SCSI Disk
Device
-1. How to use HotPlug Tool (Windows Only)
3
Connecting/Removing eSATA drive
3
If the system recognizes the eSATA drive, the icon of HotPlug Tool will
Click Finish
Finish
and launch HotPlug
Tool
Tool
.
Registration & Tech-support
5
Install HotPlug Tool
Install HotPlug Tool
Uninstall HotPlug Tool
-4. Installation on Mac System
2
SiI3132_1.1.6u_Sil_Pkg
-2. Connecting/Removing eSATA drive on Mac
3
Removing ExpressCard
4
Safely Remove Hardware
Silicon Image SiI3132 SATALink Controller
-1. How to remove EX30S on Windows
4
-2. How to remove EX30S on Mac
4
Appendix
6
http://www.ratocsystems.com/english/
Software Update and Support
http://www.ratocsystems.com/english/
Technical Support
http://www.ratocsystems.com/english/contact/support.html
[A]
[B]
Power off Card
EX30S
EX30S
EX30S
EX30S
EX30S
EX30S