User`s guide

eSATA ExpressCard/34
EX30S
User's Guide
1
2
3
4
5
6
Introduction * * * 2
-1. Package Contents * * * 2
-2. Layout * * * 2
-3. System Requirements * * * 3
-4. Specifications * * * 3
-5. Caution * * * 4
Setup * * * 5
-1. Installation on Windows System * * * 5
-2. To Verify Driver Installation (Windows) * * * 7
-3. Hot-plug tool (Windows) * * * 8
-4. Installation on Mac system * * *10
Connecting/Removing eSATA drive * * *11
-1. Windows * * *11
-2. Mac * * *15
Removing ExpressCard * * *16
-1. How to remove EX30S on Windows * * *16
-2. How to remove EX30S on Mac * * *16
Registration & Tech-Support * * *17
-1. Registration * * *17
-2. Tech-Support * * *17
Appendix * * *18
Contents
-1. Package Contents
Introduction
1
1
-2. Layout
1
eSATA Connector
ExpressCard Connector
Support Port Multiplier)
-3. System Requirements
1
-4. Specification
1
What's Port Multiplier(PM)?
?
.......
-5. Caution
1
Setup
2
-1. Installation on Windows system
2
Found New Hardware Wizard
No, not at this time
Next
Install the software automatically(Recommended)
Next
Finish
Windows XP, Server 2003
Silicon Image
SiI
3132 SATALink Controller
-2. To Verify Driver Installation
2
Silicon Image
SiI
3132 SATA
Link Controller
What's HotPlug Tool
-3. HotPlug Tool (Windows)
2
11
Add or Remove Programs Control Panel
HotPlugTool Change or Remove Programs
OK
Start Program Hot plug tool
[1] Removing eSATA drive
Stop
[2] Change HotPlug Tool setting
HotPlug Tool Window
SCSI Disk
Device
Note
-1. How to use HotPlug Tool (Windows Only)
-1. How to use HotPlug Tool (Windows Only)
3
Connecting/Removing eSATA drive
Connecting/Removing eSATA drive
3
Caution
* HotPlug tool can not be used for removing ExpressCard.
* When removing eSATA drive, follow the instructions in this chapter.
Removing eSATA drive without HotPlug Tool may cause data loss or
physical defect of eSATA drive.
* ExpressCard may be removed easily from the ExpressCard slot.
Sudden removal of the EX30S card may cause system error.
If the system recognizes the eSATA drive, the icon of HotPlug Tool will
If the system recognizes the eSATA drive, the icon of HotPlug Tool will
be shown in the task tray.
To remove eSATA drive, click
the icon of HotPlug Tool.
2.
* HotPlug Tool runs in the background.
* If the icon does not show up, install the HotPlug Tool. Refer to page 8.
* If an eSATA drive is not connected, the icon does not show up.
Connect eSATA cable to eSATA port
of the ExpressCard and
eSATA drive.
1.
eSATA cable
Finish
Tool
Registration & Tech-support
5
Install HotPlug Tool
Uninstall HotPlug Tool
-4. Installation on Mac System
2
SiI3132_1.1.6u_Sil_Pkg
-2. Connecting/Removing eSATA drive on Mac
3
Removing ExpressCard
4
Safely Remove Hardware
Silicon Image SiI3132 SATALink Controller
-1. How to remove EX30S on Windows
4
-2. How to remove EX30S on Mac
4
Appendix
6
http://www.ratocsystems.com/english/
Software Update and Support
http://www.ratocsystems.com/english/
Technical Support
http://www.ratocsystems.com/english/contact/support.html
[1]
[2]
Power off Card
EX30S
EX30S
EX30S
EX30S
EX30S
EX30S
[3]
[3] Customize