User's Guide

• Cualquier fuente de alimentación externa
utilizada con la Raspberry Pi deberá
cumplir con las correspondientes
regulaciones y normas aplicables en el
país de uso previsto. La fuente de
alimentación debe proporcionar 5V DC y
una corriente nominal mínima de 1A.
Instrucciones para un uso seguro
• Este producto no debe ser usado con una
frecuencia de reloj superior a la nominal.
(No se debe overclockear).
• No exponga este producto al agua o a la
humedad, y no lo coloque sobre una
superficie conductora mientras está en
funcionamiento.
• No exponga este producto a ningún tipo
de fuente de calor; está diseñado para un
funcionamiento fiable a temperatura
ambiente normal.
• No exponga la placa a fuentes de luz de
alta intensidad (por ejemplo, flash de
xenón o láser)
• Utilice este producto en un ambiente bien
ventilado, y no lo cubra durante el uso.
• Coloque este producto sobre una
superficie estable, plana y no conductora
mientras esté en uso, y no permita que
entre en contacto con elementos
conductores.
• Tenga cuidado al manipular este producto
para evitar daños mecánicos o eléctricos
en la placa de circuito impreso y en los
conectores.
• Evite manipular este producto mientras
está encendido. Sujételo solo por los
bordes para minimizar el riesgo de daños
por descargas electrostáticas.
• Cualquier periférico o equipo utilizado con
la Raspberry Pi debe cumplir con las
normas aplicables en el país de uso y
debe estar marcado en consecuencia
para garantizar que se cumplen los
requisitos de seguridad y rendimiento.
Para obtener todos los certificados de
conformidad y sus números de registro,
visite www.raspberrypi.com/compliance.
Svenska
Raspberry Pi Pico W
VIKTIGT: BEHÅLL DENNA
INFORMATION FÖR FRAMTIDA
REFERENS.
Varningar
• Alla externa strömförsörjningar som
används med Raspberry Pi måste uppfylla
alla tillämpliga regler och standarder i det
land där de används. Strömförsörjningen
måste tillhandahålla 5 VDC och ha en
lägsta märkström på 1A.
Instruktioner för säker användning
• Produkten bör inte överklockas.
• Utsätt inte produkten för vatten eller fukt,
och placera den inte på en ledande yta
medan den är i drift.
• Utsätt inte produkten för värme från någon
värmekälla. Den är utformad för tillförlitlig
drift vid normal rumstemperatur.
• Utsätt inte kortet för ljuskällor med hög
intensitet (t.ex. xenon-blixt eller laser)
• Använd produkten i en väl ventilerad miljö,
och täck inte över den vid användning.
• Placera produkten på en stabil, isolerad
yta vid användning, och låt den inte
komma i kontakt med ledande föremål.
• Var försiktig när du hanterar produkten för
att undvika mekaniska eller elektriska
skador på kretskortet och kontakterna.
• Undvik att hantera produkten med
strömmen på. Håll den endast i kanterna
för att undvika elektrostatiska
urladdningar.
• Eventuell kringutrustning och utrustning
som används med Raspberry Pi måste
uppfylla relevanta standarder i det land
där den används, och den bör märkas så
att säkerhets- och prestandakraven
uppfylls.
Besök www.raspberrypi.com/compliance,
för alla certifikat och nummer om
överensstämmelse.
EU Radio Equipment Directive (2014/53/EU)
Declaration of Conformity (DoC)
We, Raspberry Pi Limited, Maurice Wilkes
Building, Cowley Road, Cambridge, CB4 0DS,
United Kingdom, Declare under our sole
responsibility that the product: Raspberry Pi Pico
W to which this declaration relates is in conformity
with the essential requirements and other relevant
requirements of the Radio Equipment Directive
(2014/53/EU).
The product is in conformity with the following
standards and/or other normative documents:
SAFETY (art 3.1.a): IEC 60950-1: 2005 (2
nd
Edition) and EN 62311: 2008 EMC (art 3.1.b): EN
301 489-1/ EN 301 489-17 Ver. 3.1.1 (assessed
in conjunction with ITE standards EN 55032
and EN 55024 as Class B equipment)
SPECTRUM (art 3. 2): EN 300 328 Ver 2.1.1, EN
301 893 V2.1.0
In accordance with Article 10.8 of the Radio
Equipment Directive: The device ‘Raspberry Pi
Pico W ’ operates in compliance with harmonised
standard EN 300 328 v2.1.1 and transceives within
the frequency band 2,400 MHz to 2,483.5 MHz
and, as per Clause 4.3.2.2 for wideband
modulation type equipment, operates at a
maximum e.i.r.p. of 20dBm. The device
‘Raspberry Pi Pico W also operates in compliance
with harmonised standard EN 301 893 V2.1.1.). In
accordance with Article 10.10 of the Radio
Equipment Directive, and as per below list of
country codes, the operating bands 5150-
5350MHz are strictly for indoor usage only.
BE BG CZ DK
DE EE IE EL
ES FR HR IT CY
LV LT LU
H
U
MT
NL AT PL PT RO
SI SK FI SE UK
The Raspberry Pi complies with the relevant
provisions of the RoHS Directive for the European
Union.
WEEE Directive Statement for the European
Union
This marking indicates that this product should not
be disposed with other household wastes
throughout the EU. To prevent possible harm to
the environment or human health from
uncontrolled waste disposal, recycle it responsibly
to promote the sustainable reuse of material
resources. To return your used device, please use
the return and collection systems or contact the
retailer where the product was purchased. They
can take this product for environmental safe
recycling. Note: A full online copy of this
Declaration can be found at
www.raspberrypi.com/compliance/
WARNING: Cancer and Reproductive
Harm - www.P65Warnings.ca.gov.
FCC
Raspberry Pi Pico W FCC ID: 2ABCB-PICOW
This device complies with Part 15 of FCC Rules,
Operation is Subject to following two conditions:(1)
This device may not cause harmful interference,
and (2) This device must accept any interference
received including interference that cause
undesired operation. Caution: Any changes or
modifications to the equipment not expressly
approved by the party responsible for compliance
could void user s authority to operate the
equipment. This equipment has been tested and
found to comply within the limits for a Class B
digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful interference
in a residential installation. This equipment
generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance
with the instructions, may cause harmful
interference to radio communications. However,
there is no guarantee that interference will not
occur in a particular installation. If this equipment
does cause harmful interference to radio or
television reception, which can be determined by
turning the equipment off and on, the user is
encouraged to try to correct the interference by
one or more of the following measures: • Re-orient
or relocate the receiving antenna • Increase the
separation between the equipment and receiver
• Connect the equipment into an outlet on a
different circuit from that to which the receiver is
connected • Consult the dealer or an experienced
radio/TV technician for help.
For products available on the USA/Canada market,
only channels 1 to 11 are available for 2.4GHz
WLAN
This device and its antenna(s) must not be co-
located or operation in conjunction with any other
antenna or transmitter except in accordance with
FCC’s multi-transmitter procedures.
IMPORTANT NOTE: FCC Radiation Exposure
Statement; Co-location of this module with other
transmitter that operate simultaneously are
required to be evaluated using the FCC multi-
transmitter procedures.
This device complies with FCC RF radiation
exposure limits set forth for an uncontrolled
environment. The device contains an integral
antenna hence, the device must be installed to so
that a separation distance of at least 20cm from all
persons.
ISED
Raspberry Pi Pico W IC: 20953-PICOW
This device complies with Industry Canada
license-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this
device may not cause interference, and (2) this
device must accept any interference, including
interference that may cause undesired operation of
the device.
Le présent appareil est conforme aux CNR
d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée
aux deux conditions suivantes :(1) l'appareil ne doit
pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout
brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le
fonctionnement.
For products available on the USA/Canada market,
only channels 1 to 11 are available for 2.4GHz
WLAN Selection of other channels is not possible.
Pour les produits disponibles sur le marché USA /
Canada, seuls les canaux 1 à 11 sont disponibles
pour le réseau local sans fil 2,4 GHz. La sélection
d'autres canaux n'est pas possible. This device
and its antenna(s) must not be co-located with any
other transmitters except in accordance with IC
multi-transmitter product procedures. Cet appareil
et son antenne (s) ne doit pas être co-localisés ou
fonctionnement en association avec une autre
antenne ou transmetteur. réservés uniquement
pour une utilisation à l’intérieur afin de réduire les
risques de brouillage préjudiciable aux systèmes
de satellites mobiles utilisant les mêmes canaux.
IMPORTANT NOTE: IC Radiation Exposure
Statement: This equipment complies with IC RSS-
102 radiation exposure limits set forth for an
uncontrolled environment. This equipment should
be installed and operated with minimum separation
distance of 20cm between the device and all
persons.
Cet équipement est conforme aux limites
d'exposition au rayonnement IC RSS-102 définies
pour un environnement non contrôlé. Cet
équipement doit être installé et utilisé avec une
distance de séparation minimale de 20 cm entre
l'appareil et toutes les personnes.
INTEGRATION INFORMATION FOR THE OEM
It is the responsibility of the OEM / Host product
manufacturer to ensure continued compliance to
FCC and ISED Canada certification requirements
once the module is integrated in to the Host
product. Please refer to FCC KDB 996369 D04 for
additional information. The module is subject to the
following FCC rule parts: 15.207, 15.209, 15.247,
15.401And 15.407
Host Product User Guide Text
FCC Compliance
This device complies with Part 15 of FCC Rules,
Operation is Subject to following two conditions:
(1) This device may not cause harmful
interference, and
(2) This device must accept any interference
received including interference that cause
undesired operation.
Caution: Any changes or modifications to the
equipment not expressly approved by the party
responsible for compliance could void user s
authority to operate the equipment.
This equipment has been tested and found to
comply within the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential
installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference to
radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try
to correct the interference by one or more of the
following measures: • Re-orient or relocate the
receiving antenna • Increase the separation
between the equipment and receiver
• Connect the equipment into an outlet on a
different circuit from that to which the receiver is
connected • Consult the dealer or an experienced
radio/TV technician for help.
For products available in the USA/Canada market,
only channels 1 to 11 are available for 2.4GHz
WLAN. This device and its antenna(s) must not be
co-located or operation in conjunction with any
other antenna or transmitter except in accordance
with FCC’s multi-transmitter procedures.
ISED Canada Compliance
This device complies with Industry Canada
license-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this
device may not cause interference, and (2) this
device must accept any interference, including
interference that may cause undesired operation of
the device.Le présent appareil est conforme aux
CNR d'Industrie Canada applicables aux appareils
radio exempts de licence. L'exploitation est
autorisée aux deux conditions suivantes :(1)
l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout
brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le
fonctionnement.For products available in the
USA/Canada market, only channels 1 to 11 are
available for 2.4GHz WLAN Selection of other
channels is not possible.Pour les produits
disponibles sur le marché USA / Canada, seuls les
canaux 1 à 11 sont disponibles pour le réseau
local sans fil 2,4 GHz. La sélection d'autres canaux
n'est pas possible. This device and its antenna(s)
must not be co-located with any other transmitters
except in accordance with IC multi-transmitter
product procedures.
Cet appareil et son antenne (s) ne doit pas être co-
localisés ou fonctionnement en association avec
une autre antenne ou transmetteur.
IMPORTANT NOTE:
IC Radiation Exposure Statement:
This equipment complies with IC RSS-102
radiation exposure limits set forth for an
uncontrolled environment. This equipment should
be installed and operated with minimum separation
distance of 20cm between the device and all
persons.
Cet équipement est conforme aux limites
d'exposition au rayonnement IC RSS-102 définies
pour un environnement non contrôlé. Cet
équipement doit être installé et utilisé avec une
distance de séparation minimale de 20 cm entre
l'appareil et toutes les personnes.
Host Product Labelling; The host product must be
labelled with the following information:
"Contains TX FCC ID: 2ABCB-PICOW"
"Contains IC: 20953-PICOW "
“This device complies with Part 15 of FCC Rules,
Operation is Subject to following two conditions:
(1) This device may not cause harmful
interference, and
(2) This device must accept any interference
received including interference that cause
undesired operation.”
Important Notice to OEMs:
The FCC Part 15 text must go on the Host product
unless the product is too small to support a label
with the text on it. It is not acceptable just to place
the text in the user guide.
E-Labelling
It is possible for the Host product to use e-labelling
providing the Host product supports the
requirements of FCC KDB 784748 D02 e labelling
and ISED Canada RSS-Gen, section 4.4.
E-labelling would be applicable for the FCC ID,
ISED Canada certification number and the FCC
Part 15 text.
Changes in Usage Conditions of this Module
This device has been approved as a Mobile device
in accordance with FCC and ISED Canada
requirement. This means that there must be a
minimum separation distance of 20cm between the
Module’s antenna and any persons. A change in
use that involves a separation distance ≤20cm
(Portable usage) between the Module’s antenna
and any persons is a change in the RF exposure of
the module and, hence, is subject to a FCC Class
2 Permissive Change and a ISED Canada Class 4
Permissive Change policy in accordance with FCC
KDB 996396 D01 and ISED Canada RSP-100.
As noted above, This device and its antenna(s)
must not be co-located with any other transmitters
except in accordance with IC multi-transmitter
product procedures.
If the device is co-located with multiple antennas,
the module could be subject to a FCC Class 2
Permissive Change and a ISED Canada Class 4
Permissive Change policy in accordance with FCC
KDB 996396 D01 and ISED Canada RSP-100. In
accordance with FCC KDB 996369 D03, section
2.9, test mode configuration information is
available from the Module manufacturer for the
Host (OEM) product manufacturer.
Spain
“La operación de este equipo está sujeta a las
siguientes dos condiciones”1. Es posible que este
equipo o dispositivo no cause interferencia
perjudicial.2. Este equipo o dispositivo debe
aceptar cualquier interferencia. Incluyendo la que
pueda causar su operación no deseada.
Australia and New Zealand
Class B Emissions Compliance Statement
Warning: This is a Class B product. In a domestic
environment this product may cause radio
interference in which case the user may be
required to take adequate measures.
Japan
In door use only, except for connection to Base
stations or Land mobile relay stations for a 5.2
GHz band high-power data communication
system. Do not apply DC voltage to PoE pins.
「当該無線設備の送信は5.2GHz帯高出力データ通
信システムの基地局又は陸上移動中継局と通信す
る場合を除き屋内においてのみ可能」
R xxx
T xxx
South Korea
KCC: YYY XXX
사용자 안내문 이기기는 업무용 환경에서 사용할
목적으로 적합성평가를 받은 기기로서 가정용
환경에서 사용하는 경우전파간섭의 우려가
있습니다.본 기기는 통상 이용 상태의 경우
인체(머리, 몸통)와 20cm 초과하는 거리에서
사용되어야 합니다. 실내전용
China CMIIT ID XXXYYY
Anatel: XXX
IFETEL: XXX
TRA Registered no.
XXX
xxxYYY
APPROVED