R410A INVERTER COOLING SPLIT-TYPE ROOM Remote Controller Operation Manual Indoor Model: RS-S9KI RS-S12KI RS-S18KI Outdoor Model: RU-S9KI RU-S12KI RU-S18KI IMPORTANT NOTE: Thank you for purchasing our air conditioner. Please read this manual carefully before operating your new air conditioning unit. Make sure to save this manual for future reference.
Table of Contents Remote Controller Specifications ......................................................02 Handling the Remote Controller ....................................................03 Buttons and Functions ...................................................................04 Remote Screen Indicators ..............................................................05 How to Use Basic Functions ..........................................................06 How to Use Advanced Functions ..................
Remote Controller Specifications M odel RS-S9KI,RU-S9KI RS-S12KI,RU-S12KI RS-S18KI,RU-S18KI Rated Voltage 3.
Handling the Remote Controller Inserting and Replacing Batteries Your air conditioning unit may come with two batteries(some units). Put the batteries in the remote control before use. 1. Slide the back cover from the remote control downward, exposing the battery compartment. 2. Insert the batteries, paying attention to match up the (+) and (-) ends of the batteries with the symbols inside the battery compartment. 3. Slide the battery cover back into place.
Buttons and Functions Before you begin using your new air conditioner, make sure to familiarize yourself with its remote control. The following is a brief introduction to the remote control itself. For instructions on how to operate your air conditioner, refer to the How to Use Basic Functions section of this manual. TEM P Decreases temperate in 1°C (1°F) increments. Min. temperature is 16°C (60°F). ON/ OFF Turns the unit on or off. TEM P Increases temperate in 1°C (1°F) increments. Max.
Remote Screen Indicators Information are displayed when the remote controller is power up. Mode display DRY COOL AUTO HEAT AUTO FAN COOL HIGH Displayed when data transmitted. DRY MED Displayed when remote controller is ON.
How to Use Basic Functions Basic operation ATTENTION! Before operation, please ensure the unit is plugged in and power is available. SETTING TEMPERATURE The operating temperature range for units is 16-30°C (60-86°F)/20-28 C(68-82 F). You can increase or decrease the set temperature in 1°C (1°F) increments. AUTO Mode 2 3 1 In AUTO mode, the unit will automatically select the COOL, FAN, or HEAT(not applicable for cooling only model) operation based on the set temperature. 1.
DRY Mode (dehumidifying) 1. Press the MODE button to select DRY. 2. Set your desired temperature using the TEMP or TEMP button. 3. Press the ON/OFF button to start the unit. 2 NOTE:FAN SPEED cannot be changed in DRY mode. 3 1 FAN Mode 1. Press the MODE button to select FAN mode. 2. Press FAN button to select the fan speed: AUTO, LOW, MED or HIGH. 1 3. Press the ON/OFF button to start the unit. NOTE: You can’t set temperature in FAN mode.
Setting the TIMER TIMER ON/OFF - Set the amount of time after which the unit will automatically turn on/off. TIMER ON setting Press TIMER ON button to initiate the ON time sequence. Press Temp. up or down button for for multiple times to set the desired time to turn on the unit. Point remote to unit and wait 1sec, the TIMER ON will be activated.
How to Use Advanced Functions Swing function Press Swing button 2s SWING SWING The horizontal louver will swing up and down automatically when pressing Swing button. Press again to make it stop. Keep pressing this button more than 2 seconds, the vertical louver swing function is activated. (Model dependent) Airflow direction Each time you press the button, it will adjust the louver by 6 °. Press the button until the direction you prefer is reached.
ECO function ECO Press this button under COOL Mode to enter the energy efficient mode. Note:This function is only available under COOL mode. Under cooling mode, press this button, the remote controller will adjust the temperature automatically to 24 O C/75 OF, fan speed of Auto to save energy (only when the set temperature is less than 24O C/75 OF). If the set temperature is above 24 OC/75 OF, press the ECO button, the fan speed will change to Auto, the set temperature will remain unchanged.
11
