Owner's manual

ManualsBrandsRaritan Computer ManualsHardwareCC-SG

101

102

103

104

105

106

107

108

109

110

Table Of Contents

Chapter 1: Introduction
- Prerequisites
- Intended Audience
- Terminology/Acronyms
Chapter 2: Accessing CC-SG
- Browser-Based Access
- Thick Client Access
  - Install the Thick Client
  - Use the Thick Client
- CC-SG Window Components
- Check IP Address, Firmware Version, and Application Versions
- Power Down CC-SG
- Compatibility Matrix
Chapter 3: Configuring CC-SG with Guided Setup
- Prepare to Configure CC-SG with Guided Setup
- Guided Setup Overview
- Start Guided Setup:
- Associations
  - Create Categories and Elements
- Device Setup
  - Discover and Add Devices
- Create Groups
  - Add Device Groups and Node Groups
- User Management
  - Add User Groups and Users
Chapter 4: Creating Associations
- Associations
- Association Manager
Chapter 5: Adding Devices and Device Groups
- The Device Tab
- Device and Port Icons
- Search for Devices
- Add a Device
  - Adding a KVM or Serial Device
  - Adding a PowerStrip Device
- Discover Devices
- Edit Device
  - Edit PowerStrip Device
- Delete Device
- Configure Ports
- Device Management
- Viewing Devices
  - Tree View
  - Custom View
- Special Access to Paragon II System Devices
  - Paragon II System Controller (P2-SC)
  - IP-Reach and UST-IP Administration
- Device Group Manager
Chapter 6: Configuring Nodes and Interfaces
- View Nodes
- Nodes and Interfaces Overview
  - About Nodes
  - About Interfaces
- Add Node
- Add an Interface
- Connect to a Node
- Edit an Interface
- Delete an Interface
- Ping a Node
- Edit a Node
- Delete a Node
- Chat
- Node Groups
Chapter 7: Adding and Managing Users and User Groups
- The Users Tree
- Special User Groups
- Add User Groups
- Edit A User Group
- Delete User Group
- Add User
- Edit a User
- Delete User
- Assign Users To Group
- Delete Users From Group
- Other User and User Group Functions
Chapter 8: Policies
- Controlling Access Using Policies
  - Policy Summary
- Node Groups
- Device Groups
- Policy Manager
- Applying Policies To User Groups
Chapter 9: Configuring Remote Authentication
- Authentication and Authorization (AA)
  - Flow for Authentication
  - User Accounts
- Distinguished Names for LDAP and AD
  - Username
  - Base DN
- AD Configurations
- Add LDAP (Netscape) Module to CC-SG
- Add a TACACS+ Module
  - TACACS+ General Settings
- Add a RADIUS Module
  - RADIUS General Settings
- Specify Modules for Authentication and Authorization
- Establish Order of External AA Servers
Chapter 10: Generating Reports
- Audit Trail Report
- Error Log Report
- Access Report
- Availability Report
- Active Users Report
- Locked Out Users Report
- User Data Report
- Users in Groups Report
- Group Data Report
- AD User Group Report
- Asset Management Report
- Node Asset Report
- Active Nodes Report
- Node Creation Report
- Query Port Report
- Active Ports Report
- Scheduled Reports
- CC-NOC Synchronization Report
Chapter 11: System Maintenance
- Maintenance Mode
- Backup CC-SG
- Restore CC-SG
  - Saving and Deleting Backup Files
- Reset CC-SG
- Restart CC-SG
- Upgrade CC-SG
- Shut Down CC-SG
- Restarting CC-SG after Shutdown
- End CC-SG Session
  - Log Out
  - Exit CC-SG
Chapter 12: Advanced Administration
- Guided Setup
- Message of the Day Setup
- Application Manager
  - Adding, Editing and Deleting Applications
  - Default Applications
- Firmware Manager
- Cluster Configuration
- Configure Security
- Notification Manager
- Task Manager
- CommandCenter NOC
- SSH Access to CC-SG
- Diagnostic Console
Appendix A: Specifications (G1, V1, and E1)
- G1 Platform
- V1 Platform
- E1 Platform
Appendix B: CC-SG and Network Configuration
- Introduction
- Executive Summary
- CC-SG Access via NAT-enabled Firewall
- Security and Open Port Scans
Appendix C: User Group Privileges
Appendix D: SNMP Traps
Appendix E: Troubleshooting
- Client Browser Requirements
Appendix F: Two-Factor Authentication
- Supported Environments
- Setup Requirements
- Known Issues
Appendix G: FAQs
Appendix H: Keyboard Shortcuts

CHAPTER 8: POLICIES 95

Edit Node Group

Edit a node group to change the membership or description of the group. To edit a node group:

1. On the Associations menu, click Node Group. The Node Groups Manager window

displays.

Figure 92 Editing a Node Group

2. Click the node you want to edit in the Node Group List to the left. The details of that node

will appear in the Node Groups window.

3. Refer to the instructions in the Select Nodes or Describe Nodes sections above for details on

how to configure the node group.

4. Click Edit when you are done editing the Node Group.

Delete Node Group

1. On the Associations menu, click Node Group. The Node Groups Manager window

displays.

2. Click the node you want to delete in the Node Group List to the left.

3. On the Groups menu, click Delete.