Product Manual

PLANNING/LAYOUT
Before beginning the installation, create a plan as to the
location of the air compressor and where you are going
to mount the compressed air outlets. On the plan locate
outlets, tees, and elbows if needed.
AIR COMPRESSOR
Use a exible jumper hose from the air compressor to
the lter regulator unit to reduce vibration to the Max-
line tubing.
FILTER REGULATOR
Maxline tubing is resistant to most common petroleum
based compressor oils. Some new synthetic oils
will reduce the life of the tubing. A high quality lter
regulator is recommended to catch oils
entering the air system.
PRESSURE RATINGS
The Maxline tubing is rated for 175 psi at 70
deg F and less, 140 psi at a maximum
temperature of 140 deg F.
BENDING THE TUBING
The Maxline tubing can be bent to hold any
shape. Care should be taken not to kink
the tubing, but rather bend the tubing in a
sweeping radius around corners and
obstacles. Elbow ttings are available for
sharp corners.
ASSEMBLY OF THREADED
COMPONENTS
Apply pipe sealant/paste to all threaded
connections, except tting nuts during
assembly.
TUBING INSTALLATION
Maxline tubing will expand and contract
slightly with changes in temperature.
Use wall clips spaced 5 ft for 3/4” tubing,
3 ft for 1/2” tubing.
before closing up walls.
PLANNING/LAYOUT
Before beginning the installation, create a plan as to the
PLANNING/LAYOUT
Before beginning the installation, create a plan as to the
location of the air compressor and where you are going
to mount the compressed air outlets. On the plan locate
location of the air compressor and where you are going
to mount the compressed air outlets. On the plan locate
outlets, tees, and elbows if needed.
outlets, tees, and elbows if needed.
AIR COMPRESSOR
Use a exible jumper hose from the air compressor to
AIR COMPRESSOR
Use a exible jumper hose from the air compressor to
the lter regulator unit to reduce vibration to the Max
the lter regulator unit to reduce vibration to the Max
line tubing.
FILTER REGULATOR
Maxline tubing is resistant to most common petroleum
based compressor oils. Some new synthetic oils
Maxline tubing is resistant to most common petroleum
based compressor oils. Some new synthetic oils
will reduce the life of the tubing. A high quality lter
regulator is recommended to catch oils
will reduce the life of the tubing. A high quality lter
regulator is recommended to catch oils
entering the air system.
entering the air system.
PRESSURE RATINGS
The Maxline tubing is rated for 175 psi at 70
PRESSURE RATINGS
The Maxline tubing is rated for 175 psi at 70
deg F and less, 140 psi at a maximum
temperature of 140 deg F.
deg F and less, 140 psi at a maximum
temperature of 140 deg F.
BENDING THE TUBING
BENDING THE TUBING
The Maxline tubing can be bent to hold any
shape. Care should be taken not to kink
The Maxline tubing can be bent to hold any
shape. Care should be taken not to kink
the tubing, but rather bend the tubing in a
sweeping radius around corners and
the tubing, but rather bend the tubing in a
sweeping radius around corners and
obstacles. Elbow ttings are available for
obstacles. Elbow ttings are available for
sharp corners.
ASSEMBLY OF THREADED
COMPONENTS
ASSEMBLY OF THREADED
Apply pipe sealant/paste to all threaded
connections, except tting nuts during
Apply pipe sealant/paste to all threaded
connections, except tting nuts during
assembly.
TUBING INSTALLATION
Maxline tubing will expand and
TUBING INSTALLATION
Maxline tubing will expand and
slightly with changes in temperature.
Use wall clips spaced 5 ft for 3/4” tubing,
slightly with changes in temperature.
Use wall clips spaced 5 ft for 3/4” tubing,
3 ft for 1/2” tubing.
before closing up walls.
3 ft for 1/2” tubing.
ax
LINE
GENERAL SYSTEM
EXAMPLE LAYOUTS
INSTALLATION INSTRUCTIONS
1/2” Surface Mount Tubing
From Air Compressor
From Air
Compressor
3/4” Surface
Mount Tubing
From Air Compressor
1/2” In Wall Tubing