Specification

USGBC and related logo is a trademark owned by the U.S. Green
Building Council and is used by permission.
2
NON-SAG TEXTURED SEALANT Multi-Purpose Hybrid Silane Polyether
CRACK/JOINT FILLING: Place backer rod, where required, to prevent three-sided bonding.
Concrete joints (tooled or saw cut) must be free of contaminates and the concrete must
have at least 72 hours of cure before placement.
CLEAN-UP: Remove excess material, using acetone and disposable paper towels or cloth
rags, before it cures on placement tools and adjacent surfaces. Dispose of waste material
in compliance with local regulations.
CURING: Tack-free in 40 minutes; paintable in 1 hour at 1/4" at 70°F (21°C), 50%
relative humidity.
COLD WEATHER: Installation in low temperatures will extend cure times of the Rapid Set
®
NON-SAG TEXTURED SEALANT. To ease flow and placement in cold conditions, warm and
keep the sealant at 70°F (21°C) 24 hours prior to installation. Remove dew, frost or ice from
the substrate with acetone on a clean cloth and place sealant immediately.
WARM WEATHER: Installation in warmer temperatures 80°F to 100°F (27°C to 38°C) will
not adversely affect sealant performance. Warmer temperatures will decrease viscosity and
shorten cure time.
PACKAGING: Available in single-component, 10.1 fl. oz. (299 mL) cartridge.
COLORS: Gray.
COVERAGE: 10.1 fl. oz. (299 mL) yields 18.2 in
3
, 96 linear feet for 1/8" x 1/8" joints, 48 feet
for 1/8" x 1/4" joints, 24 linear feet for 1/4" x 1/4" joints, 12 linear feet for 1/4" x 1/2" joints.
10.1 FLUID OUNCE (299 ML) COVERAGE RATE
Depth of Joint,
Inches
Width of Joint,
Inches
Linear Feet Per
Cartridge
1/8 1/8 96
1/8 1/4 48
1/4 1/4 24
1/4 1/2 12
SHELF LIFE: NON-SAG TEXTURED SEALANT has a shelf life of 18 months from the date
of manufacture when properly stored.
STORAGE: Store in original, unopened container in a cool, dry area. Protect unopened
container from water, heat and direct sunlight. Store at 40°F to 90°F (4°C to 32°C). Elevated
temperatures will reduce shelf life.
LIMITATIONS: Do not apply greater than 1" width and ½" depth. Do not use in continuous
immersion applications. Allow treated wood and asphalt to cure for six (6) months prior
to application of NON-SAG TEXTURED SEALANT. Do not apply on frozen substrates. Test
and evaluate all paints and coatings before applying to NON-SAG TEXTURED SEALANT.
Polyurethane and oil based paints may dry slowly.
USER RESPONSIBILITY: Before using, read current technical data sheets, bulletins, product
labels and safety data sheets. It is the user’s responsibility to review the instructions and
warnings for any CTS products prior to use.
Refer to the Safely Data Sheet and www.CTScement.com for additional safety information
regarding this material.
WARNING: AVOID CONTACT WITH SKIN AND EYES. Can cause skin irritation, may cause
an allergic skin reaction, causes serious eye irritation. Wear protective gloves/protective
clothing/eye protection. In case of contact with eyes rinse immediately with plenty of water
and seek medical advice.
LIMITED WARRANTY: CTS Cement Manufacturing Corp. (CTS) warrants its materials to be
of good quality and at its option, within 18 months from date of manufacture, will replace
material proven defective or refund purchase price thereof, and such replacement or refund
shall be the limit of CTS’s responsibility. Except for the foregoing, all warranties, expressed
or implied, including merchantability and fitness for a particular purpose, are excluded. CTS
shall not be liable for any consequential, incidental, or special damages arising directly or
indirectly from the use of the materials.
L WARNING
CANCER and REPRODUCTIVE HARM - www.P65Warnings.ca.gov
Colors Gray
Stain and
Color Change,
ASTM C510
No change
Hardness, Shore A
ASTM C661
22
Tack Free Time,
ASTM C679
≤ 35 minutes
Joint Movement,
ASTM C719
+/- 35%
Adhesion-in-Peel,
ASTM C794
25 pli
Tensile Strength,
ASTM D412
130 psi (.90 MPa)
Tensile
Elongation,
ASTM D412
528%
Tear Strength,
ASTM D624
55 pli
Volatile Organic
Content,
ASTM D2369
12.45 g/l
Gun Grade Zero slump
Viscosity
1,220,000 cp +/- 300,000 cp,
Brookfield RVF TF Spindle, 4
RPM, 73°F (23°C)
Shrinkage
No visible shrinkage
after 14 days
Service
Temperature
-40°F To 200°F
(-40°C to 93°C)
Note: Data obtained at 70°F (21°C)
. ASTM Standards are current
unless otherwise stated.
VOC Compliance (Volatile Organic Compound)
Meets U.S. EPA 40 CFR 59 Subpart C & D;
CARB: California Air Resource Board; LADCO:
Lake Michigan Air Directors Consortium (Illinois,
Indiana, Michigan, Wisconsin); MRPO: Midwest
Regional Planning Organization (Illinois, Indiana,
Michigan, Ohio, Wisconsin); SCAQMD: South Coast
Air Quality Management District (Los Angeles,
Orange, Riverside, San Bernardino Counties);
and CEPA/EC: Canada Environmental Protection
Agency/Environment.
TYPICAL PHYSICAL DATA
© 2019 CTS Cement Manufacturing Corp. DS_148_EN_041519C
CTS Cement Manufacturing Corp. | 12442 Knott St., Garden Grove, CA 92841 | 800-929-3030 | www.CTScement.com