Specification

1
PRODUCT DATASHEET
DESCRIPTION: Rapid Set
®
NON-SAG TEXTURED SEALANT is a single-component,
multipurpose, fast curing, non-sag, UV stable sealant. This high-performance sealant
incorporates texturizing aggregate designed to complement most texturized surfaces. Its
hybrid silane polyether chemistry enhances both adhesive and cohesive bond, prevents
shrinkage upon cure, provides high tensile strength and flexibility, exceptional durability,
and weather resistance. NON-SAG TEXTURED SEALANT promotes superior adhesion that
outperforms the bond strength of polyurethanes, and will not foam on damp surfaces. This
environmentally friendly formulation has a low VOC content, is 100% solvent free, and
contains no isocyanates.
USES: Use NON-SAG TEXTURED SEALANT for interior and exterior applications. Its superior
sag resistance makes it ideal for use on horizontal, vertical and overhead applications,
including: filling wall joints, control joints, expansion joints, cove joints, and cracks; sealing
windows, and door frames. It is engineered for use on exterior balconies, concrete floor
slabs, driveways, garages, patios, walkways, and other vertical, horizontal, and overhead
applications. This material provides excellent adhesion to PVDF coated metal, galvanized
metal, aluminum, wood, glass, cement board, brick, concrete, stone, aged asphalt, EPDM
and SBS-modified bitumen membranes, EPS foam, roofing materials, fiberglass (FRP), vinyl
siding, and masonry. It can be used in damp, dry or cold climates, and its excellent adhesion
characteristics make it ideal for application to damp concrete substrates.
ENVIRONMENTAL ADVANTAGES: Low VOC, 100% solids, isocyanate-free products are
ideal for applications where the presence of VOCs, fumes or vapors are unacceptable,
undesirable or impractical. These products reduce the health risks of building occupants,
installers and contractors; and contribute to improved indoor and outdoor air quality.
Maximum durability and service life minimizes construction waste byproducts.
REGULATORY COMPLIANCE: Conforms to OTC rule for sealants. Meets requirements of
California Regulations: CARB, BAAQMD and SCAQMD. Conforms to USDA requirements for
non-food contact.
GREEN STANDARDS: LEED 2.2 for new construction and major renovations: Low emitting
materials (section 4.1) 1 Point. National Association of Home Builders (NAHB) Model Green
Home Building Guidelines: 5 global impact points. VOC Content: 12.45 grams / liter per
ASTM D2369. EPA Method 24 (tested at 240°F/ 115°C).
SURFACE PREPARATION: Ensure substrate is clean, sound, and free of bond inhibitors,
such as grease, oil, mold, surface water, coatings and sealers. For best results, roughen
surfaces with an abrasive disc or sand paper, then wipe with acetone. Tape off or protect
adjacent areas.
APPLICATION: Apply between a minimum temperature of 35°F (2°C) and rising, and a
maximum of 100°F (38°C). For best results, place sealants between 70°F (21°C) and 80°F
(27°C). Typical width to depth ratio is 2:1. Cut the end of the nozzle to match the width of
the joint and insert a tool to puncture the inner foil seal. Ensure the opening size of the
nozzle and foil seal are large enough to allow proper flow. Too small an opening could
result in excessive back pressure leading to failure of the rear seal. Insert the cartridge
into a caulking gun. Before placing, extrude material until an even color (without streaks)
flows out of the nozzle. Place nozzle at bottom of joint or application area to avoid trapping
air during placement. Keep the nozzle in the material during application. Using constant
pressure, carefully apply the sealant with a smooth continuous bead. If tooling is needed,
do so within 15 minutes of application.
NON-SAG TEXTURED SEALANT
Multi-Purpose Hybrid Silane Polyether
OVERVIEW
Highlights:
Complements roughly textured surfaces
Fast Curing: 15-minute working time, tack-free in
35 minutes, paintable in 1 hour
Strong Bond: Excellent adhesion to dry and
damp substrates
Interior/Exterior: Durable in tough environments
Horizontal, vertical and overhead use
Superior sag resistance
Weather and UV resistant. Non-shrink
100% solids, low VOC, no odor, and no
harmful isocyanates
Conforms to:
ASTM C920, Type S, Grade NS, Class 35, uses NT,
T2, M, G, A, & O
Federal Specification TT-S-00230-C,
Type II, Class B
Army Corps of Engineers CRD-C-541,
Type II, Class B
Canadian Standards Board CAN 19,13-M-82
MasterFormat
®
2016
07 01 90 Joint Sealant Rehabilitation/Replacement
07 92 13 Elastomeric Joint Sealants
Manufacturer:
CTS Cement Manufacturing Corp.
12442 Knott St.
Garden Grove, CA 92841
Tel: [phone] | Fax: [phone]
Web: www.CTScement.com
E-mail: [e-mail]
SEALANTS
& ADHESIVES
PRODUCT CATALOG