Safety Data Sheet 1 IDENTIFICATION Product identifier Rapid Set Fast Anchoring & Repair Adhesive (Part A) Other means of identification Product code 196031009 Recommended use Industrial use Recommended restrictions Appropriate training in the proper use and handling of this material should be provided as required under applicable regulations.
Hazard statement H315+H320: Can cause eye and skin irritation and sensitization H317: May cause allergic skin reaction H335: May cause respiratory tract irritation H411: Toxic to aquatic life with long lasting effects Precautionary statement Prevention P261: Do not breathe dust/fume/gas/mist/vapors/spray P264: Wash skin thoroughly after handling P272: Contaminated clothing should not be allowed out of the workplace P273: Avoid release to environment P280: Wear protective gloves/protective clothing/eye pr
Eye contact Immediately flush eyes with plenty of water for at least 15 minutes. Get medical attention immediately. Ingestion Immediately rinse mouth and drink 3-4 glasses of milk or water if person conscious. Do not induce vomiting. Seek medical attention, care and treatment. Most important symptoms/effects, acute and delayed Remove affected person from area. Treat symptomatically.
6 ACCIDENTAL RELEASE MEASURES Personal precautions, protective equipment and emergency procedures Keep unnecessary personnel away. Keep people away from and upwind of spill/leak. Wear appropriate protective equipment and clothing during clean-up. Cover spills with absorbent materials. Place in metal containers for recovery or disposal. Local authorities should be advised if significant spillages cannot be contained. For personal protection, see section 8 of the SDS.
Biological limit values See Section 12. Exposure guidelines None required in adequately ventilated areas. If vapor concentration exceeds 20 ppm for longer than 15 minutes, a NIOSH approved respirator for organic vapors is recommended. Appropriate engineering controls No special controls needed. General and local exhaust recommended. Individual protection measures, such as personal protective equipment Eye/face protection Splash proof goggles or chemical safety glasses.
Flammability limit – upper (%) NE Vapor pressure < 0.13 kPA @ 20°C (68°F) Vapor density No data Relative density 1.1-1.2 Solubility(ies) Solubility (water) Insoluble Partition coefficient (noctanol/water) No applicable information available Decomposition temperature No data Viscosity No data Other information Bulk density No data Partition coefficient (oil/water) 3.
Eye contact May cause eye irritation. Corneal injury is unlikely. Ingestion Acute – Low toxicity if swallowed. Harmful effects not anticipated from swallowing small amounts. Symptoms related to the physical, chemical, and toxicological characteristics See Symptoms above. Information on toxicological effects Acute toxicity No data on the product itself.
Chronic effects May cause skin disorders if contact is repeated or prolonged. Irritancy may happen if hardened product is abraded, ground, etc. 12 ECOLOGICAL INFORMATION Ecotoxicity The product is not classified as environmentally hazardous. However, this does not exclude the possibility that large or frequent spills can have a harmful or damaging effect on the environment. Toxicity Aquatic Toxicity: See below.
Mobility in soil Potential for mobility in soil is low (Koc between 500 and 2000). Given its very low Henry’s Constant, volatization from natural bodies of water or moist soil is not expected to be an important fate process. Partition Coefficient (Koc) Other adverse effects 1800-4400 estimated No data available. 13 DISPOSAL CONSIDERATIONS Disposal instructions Not a hazardous waste by RCRA criteria (40 CFR 261).
OSHA Specifically Regulated Substances (29 CFR 1910.1001-1050) Not listed CERCLA Hazardous Substance List (40 CFR 302.
Disclaimer CTS Cement Manufacturing Corporation cannot anticipate all conditions under which this information and its product, or the products of other manufacturers in combination with its product, may be used. It is the user’s responsibility to ensure safe conditions for handling, storage and disposal of the product, and to assume liability for loss, injury, damage or expense due to improper use. The information in the sheet was written based on the best knowledge and experience currently available.
Safety Data Sheet 1 IDENTIFICATION Product identifier Rapid Set Fast Anchoring & Repair Adhesive (Part B) Other means of identification Product code 196031009 Recommended use Industrial use Recommended restrictions Appropriate training in the proper use and handling of this material should be provided as required under applicable regulations.
Hazard statement H302+H312: Harmful in contact with skin or if swallowed H314: Causes severe skin burns and eye damage H317: May cause an allergic skin reaction H335: May cause respiratory tract irritation H350: May cause cancer H361: Suspected of damaging fertility or the unborn child H362: May cause harm to breast-fed children Precautionary statement Prevention P201: Obtain special instructions before use P202: Do not handle until all safety precautions have been read and understood P261: Do not breath
4 FIRST-AID MEASURES Inhalation Remove the affected person immediately to fresh air. If breathing becomes worse, seek medical attention. Give assisted respiration if breathing has stopped or is labored (Call a physician). Skin contact Remove product and flush affected area with water for 15 minutes. If irritation persists get medical attention. Eye contact Immediately flush eyes with plenty of water for at least 15 minutes. Get medical attention immediately.
General fire hazards May generate toxic or irritating combustion products. Sudden reaction and fire may result if product is mixed with an oxidizing agent. 6 ACCIDENTAL RELEASE MEASURES Personal precautions, protective equipment and emergency procedures Keep unnecessary personnel away. Keep people away from and upwind of spill/leak. Wear appropriate protective equipment and clothing during clean-up. Cover spills with absorbent materials. Place in metal containers for recovery or disposal.
*Values meaningful only when harden product is abraded, ground. Biological limit values See Section 12. Exposure guidelines None required in adequately ventilated areas. If vapor concentration exceeds 20 ppm for longer than 15 minutes, a NIOSH approved respirator for organic vapors is recommended. Appropriate engineering controls No special controls needed. General and local exhaust recommended.
Vapor pressure No data Vapor density No data Relative density 1.3-1.4 Solubility(ies) Solubility (water) <1% Partition coefficient (noctanol/water) No applicable information available Decomposition temperature No data Viscosity No data Other information Bulk density No data Partition coefficient (oil/water) Not applicable VOC (weight %) 0% 10 STABILITY AND REACTIVITY Reactivity The product is stable under normal conditions of use, storage, and transport.
Ingestion Acute – May cause irritation and bleeding of the gastrointestinal tract. Chronic – Scarring of the affected tissues may occur. Symptoms related to the physical, chemical, and toxicological characteristics See Symptoms above. Information on toxicological effects Acute toxicity No data on the product itself.
NTP Report on Carcinogens Crystalline Silica (CAS 14808-60-7) OSHA Specifically Regulated Substances (29 CFR 1910.1001-1050) Not listed Known To Be Human Carcinogen. Reproductive toxicity Suspected of damaging fertility or the unborn child. Avoid exposure to woman during early pregnancy. Specific target organ toxicity – single exposure No data. Specific target organ toxicity – repeated exposure No data. Aspiration hazard Due to the physical form of the product it is not an aspiration hazard.
Toxicity Aquatic Toxicity: No data on the product itself Acute Toxicity to FishComponents Nonylphenol Aminoethyl Piperazine LC50 (96 HRS): 0.14 mg/l LC50 (96 HRS): 2190 mg/l SPECIES: Fathead Minnow SPECIES: Fathead Minnow Acute Toxicity to Aquatic Invertebrates: Components Polyoxypropylenediamine Nonylphenol Aminoethyl Piperazine EC50 (48 HRS): 80 mg/l EC50 (48 HRS): 0.
13 DISPOSAL CONSIDERATIONS Disposal instructions Incineration is preferred. Dispose of contents/container in accordance with local/regional/national/ international regulations. Do not discharge into drains/surface waters/ groundwater. This product should not be allowed to enter drains, water courses, or the soil. Local disposal regulations Dispose in accordance with all applicable regulations.
Superfund Amendments and Reauthorization Act of 1986 (SARA) Hazard categories Sara Title III Section 312 Hazard Class: Immediate (Acute) health hazard, delayed (chronic) health hazard Section 313 Listed Ingredients: Phenol Other federal regulations Clean Air Act (CAA) Section 112 Hazardous Air Pollutants (HAPs) List Not regulated Clean Air Act (CAA) Section 112(r) Accidental Release Prevention (40 CFR 68.130) Not regulated Safe Drinking Water Act (SDWA) Not regulated US state regulations US.
HMIS® ratings Health: 2 Flammability: 1 Reactivity: 1 Disclaimer CTS Cement Manufacturing Corporation cannot anticipate all conditions under which this information and its product, or the products of other manufacturers in combination with its product, may be used. It is the user’s responsibility to ensure safe conditions for handling, storage and disposal of the product, and to assume liability for loss, injury, damage or expense due to improper use.
