Specification

2
NEWCRETE Concrete Resurfacer
WARM WEATHER: Environmental and material temperatures above 70˚F (21˚C) may
shorten setting time and increase the rate of strength gain. Higher temperatures will
have a more pronounced effect. To compensate for warm temperatures, keep material
cool, use chilled mix water.
CURING: Rapid Set
®
NEWCRETE does not require water curing or curing compound under
moderate conditions at 70˚F (21˚C). In dry, windy or hot conditions, mist with water to
maintain a continuously wet surface until the product has achieved sufficient strength.
NEWCRETE cures to a light gray color. Walk on time is approximately 2 to 3 hours.
YIELD & PACKAGING: The coverage of one 25-lb (11.3-kg) box of NEWCRETE is
approximately 75 ft
2
(7.0 m
2
) at 1/16" (0.16 cm) depth or 150 ft
2
(13.9 m
2
) at skim coat
depth. Coverage may vary due to jobsite conditions.
SHELF LIFE: NEWCRETE has a shelf life of 12 months when stored properly in a dry
location, protected from moisture, out of direct sunlight, and in an undamaged package.
USER RESPONSIBILITY: Before using CTS products, read current technical data sheets,
bulletins, product labels and safety data sheets at www.CTScement.com. It is the user’s
responsibility to review instructions and warnings for any CTS products prior to use.
WARNING: DO NOT BREATHE DUST. AVOID CONTACT WITH SKIN AND EYES. Use
material in well-ventilated areas only. Exposure to cement dust may irritate eyes, nose,
throat, and the upper respiratory system/lungs. Silica exposure by inhalation may result
in the development of lung injuries and pulmonary diseases, including silicosis and lung
cancer. Seek medical treatment if you experience difficulty breathing while using this
product. The use of a NIOSH/MSHA-approved respirator (P-, N- or R-95) is recommended
to minimize inhalation of cement dust. Eat and drink only in dust-free areas to avoid
ingesting cement dust. Skin contact with dry material or wet mixtures may result in
bodily injury ranging from moderate irritation and thickening/cracking of skin to severe
skin damage from chemical burns. If irritation or burning occurs, seek medical treatment.
Protect eyes with goggles or safety glasses with side shields. Cover skin with protective
clothing. Use chemical resistant gloves and waterproof boots. In case of skin contact
with cement dust, immediately wash off dust with soap and water to avoid skin damage.
In case of skin contact with wet concrete, wash exposed skin areas with cold running
water as soon as possible. In case of eye contact with cement dust, flush immediately
and repeatedly with clean water, and consult a physician. If wet concrete splashes into
eyes, rinse eyes with clean water for at least 15 minutes and go to the hospital for
further treatment.
Please refer to the SDS and www.CTScement.com for additional safety information
regarding this material.
LIMITED WARRANTY: CTS CEMENT MANUFACTURING CORP. (CTS) warrants its materials
to be of good quality and, at its option, will replace or refund the purchase price of any
material proven to be defective within one (1) year from date of purchase. The above
remedies shall be the limit of CTS’s responsibility. Except for the foregoing, all warranties
expressed or implied, including merchantability and fitness for a particular purpose, are
excluded. CTS shall not be liable for any consequential, incidental, or special damages
arising directly or indirectly from the use of the materials.
L WARNING
CANCER and REPRODUCTIVE HARM - www.P65Warnings.ca.gov
Compressive Strength, ASTM C109 Mod.
24 hours 2000 psi (13.7 MPa)
28 days 4000 psi (31.0 MPa)
All data produced at 70°F (21°C) at 3 quarts of water
TYPICAL PHYSICAL DATA
© 2017 CTS Cement Manufacturing Corp. DS_067_EN_120117A
CTS Cement Manufacturing Corp. | 12442 Knott St., Garden Grove, CA 92841 | 800-929-3030 | www.CTScement.com
USGBC and related logo is a trademark owned by the U.S. Green
Building Council and is used by permission.