Owner's manual

6
SpecificationS
SA
Series
SB
Series
SBX
Series
SCX
Series
SD
Series
Model SC4 Straightener with individually adjustable upper
rolls. This 4” x .085” capacity straightener with its coun-
terbalanced swing-open top is a Rapid-air original and
continues to be available due to customer acceptance and
demand. Dial-type indicators for roll settings are optional.
A NOTE ON ROLL DIAMETER AND QUANTITY:
The smaller the roll diameter in a straightener the better
it is able to remove distortions in the strip of material.
Rapid-Air straighteners are designed to optimize all
factors (including number of rolls, diameter and position)
within the published material capacities and specifica-
tions for each model.
Model SC4
Max Effective Max Straightening Pinch Drive Input
Material Straightening Speed Rolls Rolls (2) Motor Power
Model Width Range per min Speed No., Dia. Dia. (HP) (vac/ph)
SA3 3” (76mm) .002” - .030” (.051-.76mm) 700” (1778cm) Standard 11, 3/8 (9.53mm) 1-1/2 (38.1mm) 1/4 115/1
SA3M 3” (76mm) .002” - .030” (.051-.76mm) 1,400” (3556cm) Medium 11, 3/8 (9.53mm) 1-1/2 (38.1mm) 1/2 115/1
SB4 4” (102mm) .003” - .050” (.076-1.27mm) 700” (1778cm) Standard 11, 5/8 (15.86mm) 1-1/2 (38.1mm) 1/2 115/1
SB4M 4” (102mm) .003” - .050” (.076-1.27mm) 1,400” (3556cm) Medium 11, 5/8 (15.86mm) 1-1/2 (38.1mm) 1/2 115/1
SBX4 4” (102mm) .004” - .080” (.10-2.03mm) 825” (2100cm) Standard 9, 7/8 (22.23mm) 1-3/4 (44.45mm) 3/4 115/1
SBX8 8” (203mm) .004” - .070” (.10-1.78mm) 825” (2100cm) Standard 9, 7/8 (22.23mm) 1-3/4 (44.45mm) 3/4 115/1
SBX12 12” (305mm) .004” - .060” (.10-1.52mm) 825” (2100cm) Standard 9, 7/8 (22.23mm) 1-3/4 (44.45mm) 3/4 115/1
SBX4M 4” (102mm) .004” - .080” (.10-2.03mm) 1,650” (4200cm) Medium 9, 7/8 (22.23mm) 1-3/4 (44.45mm) 1 115/1
SBX8M 8” (203mm) .004” - .070” (.10-1.78mm) 1,650” (4200cm) Medium 9, 7/8 (22.23mm) 1-3/4 (44.45mm) 1 115/1
SBX12M 12” (305mm) .004” - .060” (.10-1.52mm) 1,650” (4200cm) Medium 9, 7/8 (22.23mm) 1-3/4 (44.45mm) 1 115/1
SCX6 6” (152mm) .006” - .100” (.15-2.54mm) 825” (2100cm) Standard 9, 1-3/8 (34.93mm) 1-3/4 (44.45mm) 1 115/1
SCX12 12” (305mm) .006” - .090” (.15-2.29mm) 825” (2100cm) Standard 9, 1-3/8 (34.93mm) 1-3/4 (44.45mm) 1 115/1
SCX18 18” (457mm) .006” - .080” (.15-2.03mm) 825” (2100cm) Standard 9, 1-3/8 (34.93mm) 1-3/4 (44.45mm) 1 115/1
SCX24 24” (610mm) .006” - .065” (.15-1.65mm) 825” (2100cm) Standard 9, 1-3/8 (34.93mm) 1-3/4 (44.45mm) 1 115/1
SCX6M 6” (152mm) .006” - .100” (.15-2.54mm) 1,650” (4200cm) Medium 9, 1-3/8 (34.93mm) 1-3/4 (44.45mm) 2 230/1
SCX12M 12” (305mm) .006” - .090” (.15-2.29mm) 1,650” (4200cm) Medium 9, 1-3/8 (34.93mm) 1-3/4 (44.45mm) 2 230/1
SCX18M 18” (457mm) .006” - .080” (.15-2.03mm) 1,650” (4200cm) Medium 9, 1-3/8 (34.93mm) 1-3/4 (44.45mm) 2 230/1
SCX24M 24” (610mm) .006” - .065” (.15-1.65mm) 1,650” (4200cm) Medium 9, 1-3/8 (34.93mm) 1-3/4 (44.45mm) 2 230/1
SCX6H 6” (152mm) .006” - .080” (.15-2.03mm) 4,100” (10400cm) High 9, 1-3/8 (34.93mm) 1-3/4 (44.45mm) 3 230/1
SCX12H 12” (305mm) .006” - .070” (.15-1.78mm) 4,100” (10400cm) High 9, 1-3/8 (34.93mm) 1-3/4 (44.45mm) 3 230/1
SCX18H 18” (457mm) .006” - .060” (.15-1.52mm) 4,100” (10400cm) High 9, 1-3/8 (34.93mm) 1-3/4 (44.45mm) 3 230/1
SCX24H 24” (610mm) .006” - .055” (.15-1.40mm) 4,100” (10400cm) High 9, 1-3/8 (34.93mm) 1-3/4 (44.45mm) 3 230/1
SD6 6” (152mm) .006” - .125” (.15-3.18mm) 825” (2100cm) Standard 9, 1-3/8 (34.93mm) 1-3/4 (44.45mm) 2 230/1
SD12 12” (305mm) .006” - .125” (.15-3.18mm) 825” (2100cm) Standard 9, 1-3/8 (34.93mm) 1-3/4 (44.45mm) 2 230/1
SD18 18” (457mm) .006” - .100” (.15-2.54mm) 825” (2100cm) Standard 9, 1-3/8 (34.93mm) 1-3/4 (44.45mm) 2 230/1
SD24 24” (610mm) .006” - .090” (.15-2.29mm) 825” (2100cm) Standard 9, 1-3/8 (34.93mm) 1-3/4 (44.45mm) 2 230/1
A right-to-left material ow direction is standard for above models –– left-to-right optional at no additional cost.
SC4 4” (102mm) .015” - .085” (.38-2.13mm) 825” (2100cm) Standard 9, 1-1/4 (31.75mm) 1-1/4 (31.75mm) 1 115/1