RANGEMASTER REFRIGERATED BEVERAGE CENTRE Installation Operation and Maintenance Instructions Refrigerated Beverage Centre with MicroSentry™ Refrigeration Monitor RBC38 RBC60
TABLE OF CONTENTS Unpacking your refrigerator............................................ 2 Removing the packaging............................................. 2 Warranty Registration .................................................. 2 Installing your refrigerator............................................... 3 Selecting the location.................................................. 3 Cabinet Clearances .................................................... 3 Leveling legs ..................................
UNPACKING YOUR BEVERAGE CENTRE Important Safety Instructions Warnings and safety instructions appearing in this guide are not meant to cover all possible conditions and situations that may occur. Common sense, caution, and care must be exercised when installing, maintaining, or operating this appliance. Recognize Safety Symbols, Words, and Labels. Note to Customer This merchandise was carefully packed and thoroughly inspected before leaving our plant.
INSTALLING YOUR BEVERAGE CENTRE Select Location The proper location will ensure peak performance of your appliance. We recommend a location where the unit will be out of direct sunlight and away from heat sources. To assure your product performs to specifications the recommended installation location temperature range is from 18 to 27°C for indoor built in units, 18 to 32°C for indoor freestanding units, and 4 to 38°C for outdoor units.
ELECTRICAL CONNECTION 13A must be used and fitted with a 13A fuse “ASTA” approved to BS 1363. Electrical Connection Use nominal 230 VAC, 50 Hz only. Do not use an extension cord with this appliance. If you replace the fuse, the cover must be refitted. If the cover is lost, the plug must not be used until a replacement has been obtained from your supplier. The color of the fuse cover is that of the insert in the base of the fuse recess or elsewhere on the plug.
USING YOUR MicroSentry™ REFRIGERATION MONITOR Door Switch Control Light Switch Figure 3 NOTE During initial startup, or anytime power is interrupted, there will be an approximate 5 minute delay before the refrigerator starts. During this period the controller will be assessing the temperature in the refrigerator and the display will appear erratic, this is normal. The desired temperature set point can be programmed during this start up period.
USING YOUR MicroSentry™ REFRIGERATION MONITOR 1) Press and release the “SET button four times. “cnd” will be displayed on the screen. 2) While “cnd” is displayed, press and hold the “SET” button. The display will show the number of weeks the refrigerator has been running. 3) While holding the “SET” button, press and release the ON/OFF button. The number shown on the display will reset to 0. 4) Release the “SET” key. Alarm Mute Press any key to mute the audible portion of an alarm,.
DIMENSIONS FOR RBC38 GLASS DOOR 927mm INSTALLER: Please leave these instructions with the user. DATA BADGE LOCATION: Front left-hand side of the refrigerator compartment.
DIMENSIONS FOR RBC60 GLASS DOOR INSTALLER: Please leave these instructions with the user. DATA BADGE LOCATION: Front left-hand side of the refrigerator compartment.
RBC38 BEVERAGE CENTRE FEATURES Insert Wine Bottles The wine rack pull-out shelf holds four (4) bottles. See Figure 4 for typical wine bottle orientation. Loading Tips and Suggestions The wine rack can be located at any shelf support but it is recommended it be located toward the uppermost position in the cabinet. The utility shelves can be located at any position depending on bottle size. See Figure 5.
RBC60 BEVERAGE CENTRE FEATURES Loading Tips and Suggestions The wine rack pull-out shelf holds eight (8) bottles. See Figure 6 and Figure 8 for typical wine bottle orientation. The wine rack is located at the bottom of the cabinet just above the fixed wooden bottle cradle which will store 6 bottles of wine. The glass and metal shelves and the fixed wire rack are for general beverage storage, such as beer and soft drinks.
ENERGY SAVING TIPS The following suggestions will minimize the cost of operating your refrigeration appliance. 1. Do not install your appliance next to a hot appliance, (cooker, dishwasher, etc.). heating air duct, or other heat sources. 2. Install product out of direct sunlight. 3. Assure the toe grille vents at front of unit beneath door is not obstructed and kept clean to allow ventilation for the refrigeration system to expel heat. 4. Plug your appliance into a dedicated power circuit.
CARE AND CLEANING OF YOUR BEVERAGE CENTRE Condenser The condenser underneath the cabinet does not require frequent cleaning; however, satisfactory cooling depends on adequate ventilation over this heat exchanger. It is recommended to annually clean the condenser by vacuuming and brushing. To access the condenser, the unit must be pulled out from the installation, and the lower machine compartment access cover removed.
CARE AND CLEANING OF YOUR BEVERAGE CENTRE Door alignment The door should be parallel to the sides and top of the refrigerator. If alignment is necessary the door may be adjusted by loosening the 2 screws which secure the hinge adapter brackets to the door and adjusting the door side to side. Use a 5/32” hex key for this procedure. (See Figure 9 below). Remove the top hinge pin to remove the door. Hinge adapter screws loosen these to adjust door, on the top and bottom of the door. 7.
TROUBLESHOOTING YOUR BEVERAGE CENTRE Before You Call for Service If the unit appears to be malfunctioning, read through this manual first. If the problem persists, check the troubleshooting guide below. Locate the problem in the guide and refer to the cause and its remedy before calling for service. The problem may be something very simple that can be solved without a service call. Some remedies listed in the Troubleshooting Guide are very complex.
HOW TO OBTAIN SERVICE If You Do Need Service If you do need service, contact your dealer or Rangemaster. In any correspondence, refer to the model number and serial number of your unit which is located on the upper left hand side of the wall liner. Retain your proof of purchase. Please complete the appliance details below and keep them safe for future reference. This information will enable us to accurately identify your particular appliance and help us to help you.
GUARANTEE Free 1st Year Parts & Labour Guarantee Covers goods for the period of 12 months from the date of purchase subject of the below exclusions. Terms and Conditions The appliance • • • • • • • • • Has been correctly installed in accordance with current legislation, relevant British Standards, and Codes of Practice by a competent person. Has been used solely in a domestic environment and for domestic purposes. Guarantee only applies to normal domestic use.
APPENDIX A, ADDITIONAL MicroSentry™ FEATURES Information Menu: displayed. The following features are available on the Information Menu. • Current Temperature • Maximum Stored Temperature • Minimum Stored Temperature • Total Operating Time Of The Condenser • Keypad Lockout Keypad Lockout Feature (Loc): This feature is useful for prohibiting changes in the temperature set point or accidentally turning the unit off.
NOTES
Clarence Street, Royal Leamington Spa, Warwickshire, CV31 2AD, England. Tel: +44 (0) 1926 457400 Fax: +44 (0) 1926 450526 E-mail: consumers@rangemaster.co.uk www.rangemaster.co.uk 41011822 Rev D 6/3/13 All specifications and product designs subject to change without notice. Such revisions do not entitle the buyer to corresponding changes, improvements, additions, replacements or compensation for previously purchased products.
