4 ENGAGE MAIN MIC ENGAGE 2 4 4 4 MIN 4 MIN OL 2 BOOST 2 2 CUT BOOST 2 CUT 2 REMOTE MIC BASS TREBLE 4 MAIN MIC MAX 6 MAX 6 8 8 MIC EQ 4 4 4 BOOST 2 CUT 2 2 BOOST 2 BOOST BASS CUT 2 2 BOOST MID CUT 2 HI-MID CUT CROSSFADER CONTOUR EQ A EQ ENGAGE 4 2 TREBLE 4 4 4 4 A 0 2 4 6 8 10 A F 60 CUE A 10 0 LINE 3 PH/LN1 CUE B 0 2 4 6 8 10 LINE 4 PH/LN2 8 2 6 4 4 6 2 8 0 10 B 0 2 4 6 0dB 10 LINE 5 LINE 6 INPUT SELECT AC
IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block any ventilation openings. Install in accordance with manufacturer’s instructions. If rackmounting, provide adequate ventilation.
OPERATORS MANUAL MP 22z CLUB MIXER A MAIN MIC INPUT SELECT TREBLE 2 2 CUT BOOST LINE 3 PH/LN1 B INPUT SELECT LINE 4 LINE 5 LINE 4 PH/LN2 AUX 4 TREBLE LINE 5 LINE 6 2 2 CUT BOOST OUTPUT LEVELS 6 2 6 4 8 2 PEAK dBu 6 4 8 8 2 +8 4 EQ ENGAGE 4 CUE A HI-MID 2 2 4 CUE B 4 4 10 10 10 10 4 10 LEVEL 10 0 ZONE 2 10 0 ZONE 1 +5 +3 +1 MASTER LEVEL 2 2 4 0 HI-MID 2 2 TREBLE 4 4 EQ ENGAGE 4 0 -1 10 10 -3 CUT BOOST 2 2 CUT MIC EQ BASS 4 BOOST 8 0dB 8
FRONT PANEL DESCRIPTION A MAIN MIC INPUT SELECT TREBLE 2 2 CUT BOOST LINE 3 PH/LN1 B INPUT SELECT LINE 4 LINE 5 LINE 4 PH/LN2 AUX 4 TREBLE LINE 5 LINE 6 2 2 CUT BOOST OUTPUT LEVELS 6 2 6 4 8 2 PEAK dBu 6 4 8 8 2 +8 4 EQ ENGAGE 4 CUE A HI-MID 2 2 4 CUE B 4 4 10 10 10 10 4 10 LEVEL 10 0 ZONE 1 10 0 ZONE 2 +5 +3 +1 MASTER LEVEL 2 2 4 0 HI-MID 2 2 TREBLE 4 4 EQ ENGAGE 4 0 -1 10 10 -3 CUT BOOST 2 2 CUT MIC EQ BASS 4 BOOST 8 0dB 8 0dB 6 6
w MAIN & REMOTE MIC OVERLOAD indicator: Monitors both Microphone Inputs, before and after the MIC EQ. It lights whenever these levels exceed 4 dB below clipping. Occasional flickering is normal; however, it should not be allowed to light steadily. e MAIN MIC ENGAGE switch: When pressed, ENGAGES the MAIN MIC Input. The adjacent red LED flashes whenever the switch is pressed in, signalling that the Main Mic is on. r MAIN MIC LEVEL control: Adjusts the Level of the front panel MAIN MIC Input.
REAR PANEL DESCRIPTION (OUT) TRIM 6 TRIM 5 L L L SEND (OUT) R MP 22z AUX LINE IN L (IN) LINE PHONO (RIAA) PH/LN 1 R R PH/LN 2 LINE PHONO (RIAA) LINE 4 LINE 5 MIC/AUX TO ZONE 1 LINE 6 RETURN (IN) BALANCED 1/4" TIP (+) RING (–) SLEEVE (GND) L MASTER R L LINE 3 ACN001.187.837 MADE IN U.S.A.
MP 22z CONNECTION When first connecting the MP 22z to other components, leave the power supply for last. This gives you a chance to make mistakes and correct them without damaging your fragile speakers, ears and nerves. All of the line level inputs are unbalanced RCA connectors. Inputs PH/LN1, LINE 3, LINE 4 and LINE 5 appear on Channel A; while PH/LN2, LINE 4, LINE 5 and LINE 6 each appear on Channel B. The only restriction is the assignment of the Phono Inputs, one per Channel A and Channel B.
OPERATING INSTRUCTIONS INITIAL OPERATION For starters, connect a CD player to LINE 1 Input and set the PHONO/LINE switch to LINE. If a turntable is used, set this switch to PHONO. Make sure all faders are set to zero, the MIC and EQ are disengaged (switches out) and all rotary controls are either fully CCW (LEVEL controls) or in their center detents (EQs), whichever applies. Leave the rear panel INPUT TRIMS at full CW (factory preset). Switch the Channel A INPUT SELECT to PH/LN 1.