Randell Manufacturing, Inc. OWNERS MANUAL This manual provides information on installation, operating, maintenance, troubleshooting & replacement parts for PRODUCTION FREEZERS NOTIFY CARRIER OF DAMAGE AT ONCE. It is the responsibility of the consignee to inspect the container upon receipt of same and to determine the possibility of any damage, including concealed damage. Randell suggests that if you are suspicious of damage to make a notation on the delivery receipt.
TABLE OF CONTENTS Page 2 .......................................................................................................Congratulations Page 3 ....................................................................................... Factory Correspondence Page 4 ................................................................................................ Serial No. Location Page 5 ......................................................................................
Retain this manual for future reference Notice: Due to a continuous program of product improvement, Randell Manufacturing reserves the right to make changes in design and specifications without prior notice. Notice: Please read the entire manual carefully before installation. If certain recommended procedures are not followed, warranty claims will be denied.
Randell Manufacturing Serial Number Locations 1995 to Present SERIES 2000 (Reach-Ins) Serial number is located on the upper left hand interior wall. 9300, 9400, 9800 Series (Back-mount compressors) Serial number is located on the upper left hand interior wall. 20000 Series (Low Profile Cooking Equipment Stands) Serial number is located on the upper left hand interior wall. 9200 Series (Side-mount compressors) Serial number is located on the upper left hand interior wall. 9800A Series Drop-In Frost Tops.
Section I - Randell Manufacturing Limited Warranty LABOR Randell manufacturing warrants all repair labor charges on their equipment for the first 90 days. During the first 90 days work authorizations are not required for in warranty repairs. However, repair times are limited to certain flex rate schedules and hours will be deducted from service invoice if they extend past allotted times without prior approval and a work authorization number.
Warranties are effective from the date of shipment, with a 30 day window to allow for installation and set-up. Where equipment is shipped to any site other than final installation Randell will honor extended labor warranty for a period of 12 months following installation with proof of start date, up to a maximum of 18 months from date of purchase. When the optional 5 year extended compressor warranty is purchased, Randell will pay for the replacement compressor only.
Our export warranties will cover all non-electrical parts for a period of one year from the date of shipment to be free of defects on material or workmanship. Electrical parts are also covered if ordered and operated on 60 hertz. Electrical components, ordered and operated on 50 hertz, are warranted for the first 90 days from shipment only. Service labor is covered for first 90 days with authorization from factory prior to service. Warranty is automatically initiated 60 days from ship date.
3. Ventilation - The air cooled self-contained freezer requires a sufficient amount of cool clean air. Avoid placing the freezer near heat generating equipment such as ovens ranges heaters, fryers, steam kettles, etc. and out of direct sunlight. Avoid locating the self-contained freezer in an unheated roam or where the room temperature may drop below 55 degrees F. or above 90 degrees F. C. Electrical Supply The wiring should be done by a qualified electrician in accordance with local electrical codes.
6. Drop in units must have 405 square inches of cross flow ventilation per side. Equal to or greater than the louvers provided with each unit at the time of purchase. 7. Check defrost setting for both number of defrost settings and time of defrost activation. Note: All motors are oiled and sealed. Note: All self-contained models are shipped from the factory with the service valves opened ready for operation.
When the defrost termination senses 58 degrees, the coil is fully defrosted and the compressor operation is automatically resumed; defrost and drain pan heaters are automatically de-energized and the compressor is activated. The coil fans are delayed from starting at the termination of a defrost cycle. When the thermostat senses a coil temperature of 35 degrees, drain line heater and fan operation is automatically resumed. The freezer operation is now completely resumed.
Diagram C - Resetting self-closing hinge Loosen set screw, using a flat blade screwdriver turn bottom hinge (2) turns. Turn clockwise on left hinged doors, counterclockwise on right hand doors. Hold hinge in wound position with screwdriver and tighten set screw.
Diagram F - Doors with cam lift closures To adjust or align cam lift doors, remove hinge cover and loosen the three machine screws on door portion of hinge plate, then pull hinge side of door in or out as necessary to align door with cabinet front for proper gasket sealing (To make door tighter move adjustment plate inward, to loosen move adjustment plate out). Tighten hinges, replace hinge cover and re-install door.
Recommended cleaners for specific situations JOB CLEANING AGENT COMMENTS Routine cleaning Soap, ammonia, detergent Medallion Apply with a cloth or sponge Fingerprints and smears Arcal 20, Lac-O-Nu, Ecoshine Provides a barrier film Stubborn stains and discoloration Cameo, Talc, Zud, First Impression Rub in the direction of the polish lines.
Section V Troubleshooting PROBLEM POSSIBLE CAUSE REMEDY A. Freezer not running 1. Circuit breaker tripped 2. Power cord unplugged 3. Thermostat turned off 4. Unknown 1. Reset 2. Plug in 3. Turn on 4. Call service agency B. Condensing unit operates for long periods or runs continuously 1. Excessive heat load placed into unit 2. Prolonged or too frequent door openings or door ajar. 1. Allow unit sufficient time to remove heat. 2. Make sure door is closed when not in use.
PROBLEM POSSIBLE CAUSE REMEDY D. Temperature too high 1. Check power cord and circuit breaker 2. Temperature control set too high 3. Dirty condenser coil 4. Evaporator coil froze 1. Plug in cord or reset breaker 2. Adjust control 5. Unknown 3. Clean coil 4. Unplug unit, defrost coil then adjust cold control to warmer position 5. Call service agency E. Compressor runs but unit not cooling 1. Fan blades have encountered an obstruction 2. Unknown 1. Check for obstruction and free fan blade 2.
Randell Manufacturing., Inc. Authorized Parts Distributors DEPOT #1 CASE PARTS CO. 877 Monterey Pass Road Monterey Park, CA 91754 1-800-621-7884 (CA ONLY) 1-800-421-0271 DEPOT #5 COMMERCIAL PARTS 5310 E. 25th Street P.O. Box 18688 Indianapolis, IN 46218-0688 1-800-727-8710 DEPOT #2 REFRIGERATION HARDWARE SUPPLY 632 Foresight Circle Grand Junction, CO 81505 1-800-423-2446 1-800-537-8300 (PAC. COAST) DEPOT #6 HARRISON SUPPLY Ridley Creek Plaza 5153 West Chester Pike P.O.
