OPERATOR’S MANUAL This manual provides information on installation, operating, maintenance, trouble shooting & replacement parts for 8000N Series Preparation Tables NOTIFY CARIER OF DAMAGE AT ONCE. It is the responsibility of the consignee to inspect the container upon receipt of same and to determine the possibility of any damage, including concealed damage. Randell suggests that if you are suspicious of damage to make a notation on the delivery receipt.
Table of Contents page 2………………………………….…………Congratulations page 3……………………………………Parts & Service Hotline page 3………………………………...…Serial Number Location page 4-7……………………………….Randell Limited Warranty page 8…………………………………………Unit Specifications page 9-10…..……………………………………...Unit Operation page 11………………………………..Drawer Track Installation page 12-13………………………..…Preventative Maintenance page 14………………………………………..Electrical Diagram page 15……………………………………..……Troubleshooting page 16-19…………………………….….....
In addition, all Randell food service equipment is backed by some of the best warranties in the food service industry and by our professional staff of service technicians. Retain this manual for future reference. NOTICE: Due to a continuous program of product improvement, Randell reserves the right to make changes in design and specifications without prior notice. NOTICE: Please read the entire manual carefully before installation.
Warranty Policies Congratulations on your purchase of a Randell Manufactured piece of equipment. Randell believes strongly in the products it builds and backs them with the best warranty in the industry. Standard with every unit comes the peace of mind that this unit has been thoroughly engineered, properly tested and manufactured to excruciating tolerances, by a manufacturer with over 30 years of industry presence.
Temperature adjustments are not covered under warranty, due to the wide range of ambient conditions. For warranty inquiries call our Field Service Department at: 1-800-621-8560. WHEN OPTIONAL 5 YEAR COMPRESSOR WARRANTY APPLIES 1. Provide reimbursement to an ASA for the cost of locally obtained replacement compressor in exchange for the return of the defective compressor sent back freight prepaid.
NOTICE: FOOD LOSS IS NOT COVERED UNDER WARRANTY 3. Repairs caused by abuse such as broken glass, freight damage, excessive force, or scratches and dents. 4. Electrical component failure due to water damage from cleaning procedures. 5. Drawer repairs that are the result of improper drawer track installation. QUOTATIONS Verbal quotations are provided for customer convenience only and are considered invalid in the absence of a written quotation.
DAMAGES All crating conforms to general motor carrier specifications. To avoid concealed damage, we recommend inspection of every carton upon receipt. In the event the item shows rough handling or visible damage to minimize liability, a full inspection is necessary upon arrival. Appearance of damage will require removing the crate in the presence of the driver. A notation must be placed on the freight bill and signed for by the truck driver at the time of delivery.
Unit Specifications 8260N pictured Volts Amp s NEM A R-404A / OZ. Cub Ft BTU rating of Cond unit Model L D H Work Hgt. 8148N 48" 33" 42.9" 35" 1 (27”) 1/3 115 9 5-15P 16 9 1380 8260N 60” 33” 42.9” 35” 2 (24”) 1/3 115 9 5-15P 16 14.8 1380 8268N 68” 33” 42.9” 35” 2 (27”) 1/3 115 9 5-15P 16 17.8 1380 8383N 83” 33” 42.9” 35” 2 (24”), 1 (21”) ½ 115 12 5-15P 24 23.5 2385 8395N 95” 33” 42.9” 35” 3 (27”) ½ 115 12 5-15P 24 28.
Unit Operation Randell has attempted to preset the cold controls to ensure that your unit runs at an optimum temperature, but due to varying ambient conditions, including elevation, food product as well as type of operation, you may need to alter this temperature. Additional adjustments can be made (within limits) by turning the control dial up or down until the desired temperature is reached. Please allow 24 hours between adjustments.
Unit Operation (cont.) Figure 2 illustrates the evaporator blower coil assembly inside the lower refrigerated base. The thermostat adjustment knob is located at the top, front of the coil assembly. MORNING STARTUP (PREP RAIL) 1. Rail cleaning may be performed at this time. 2. Turn on upper rail with switch located inside mechanical compartment. 3. Allow 30 minutes with lids closed for the rail to cool down before loading product.
Unit Operation (cont.) DRAWER REMOVAL AND INSTALLATION To remove and re-install individual drawers and drawer tracks, please refer to Figure 2 below for proper installation instructions. Figure 2 unifiedbrands.
Preventive Maintenance Randell strongly suggests a preventive maintenance program which would include the following Monthly procedures: If a failure of the equipment is a direct result of any of the Preventative Maintenance guidelines being neglected the repairs will not be covered under warranty. 1. Cleaning of all condenser coils. Condenser coils are a critical component in the life of the compressor and must remain clean to assure proper air flow and heat transfer.
Preventive Maintenance (cont.
Electrical Diagram 14 800-621-8560
Trouble Shooting Guide SYMPTOM Unit doesn't run Unit short cycles Unit runs constantly Rail not cold enough/base temp OK Unit too cold Base warm/rail temp is OK Unit noisy POSSIBLE CAUSE PROCEDURE 1. No power to unit 2. Temperature control turned off 3. Temperature control faulty 4. Compressor overheated 5. Condenser fan faulty 6. Overload protector faulty 7. Compressor relay faulty 8. Compressor faulty 1. Condenser coil dirty 2. Condenser fan faulty 3. Compressor faulty 4.
Replacement Parts 16 800-621-8560 8000N Series – exploded view
Replacement Parts 8000N Series – exploded view Drawer Assembly unifiedbrands.
Replacement Parts 18 800-621-8560 8000N Series – exploded view Mechanical area
Replacement Parts 8000N Series – exploded view Evaporator Coil Assembly unifiedbrands.
Replacement Part List ITEM 1 2 3 4 5 6 6A 6B 6D 6E 7 7A 8 8A 8B 9 9A 9B 10 10A 10B 11 11B 12 13 14 14A 14B 15 16 16A 17 17A 17B 18 18A 18B 18C 20 DESCRIPTION 6" caster w/ break 6" caster w/o break 4" caster w/ break 4" caster w/o break 6" leg w/ bullet foot s/s back panel 48" s/s back panel 60" s/s back panel 68" s/s back panel 83" s/s back panel 95" Power cord 16/3 9' Power cord 12/3 9' Door right hand 27"x26" Door right hand 24"x26" Door right hand 21"x26" Door left hand 27"x26" Door left hand 24"x26
19 19A 19B 19C 20 20A 20B 20C 20D 20E 20F 20G 21 21A 21B 21C 22 22A 22B 23 23A 24 25 26 27 28 29 30 31 32 33 34 34A 34B 35 35A 35B 38 38A 38B 38C 39 39A 40 40A 41 41A 42 43 44 21" Dwr front 24" Dwr front 27" Dwr front 27" Dwr front - 3 tier 21" Dwr frame 24" Drwr frame 27" Dwr frame 27" Dwr frame - 3 tier Drawer tracks (1L&1R) Dwr handle Dwr bearing Dwr bearing bolt Dwr gasket 11.3 x 18.75 Dwr gasket 11.3 x 21.75 Dwr gasket 11.3 x 24.75 Dwr gasket 7.5 x 24.
45 46 47 48 49 51 52 52A 52B 52C 52D 52E 52F 53 53A 53B 54 55 56 57 58 59 60 61 61A 61B 61C 61D 61E 62 63 64 64A 64B N/S N/S 22 Evap coil drain tube Evap coil housing - rear panel Evap coil housing - front panel Evap coil housing -side Evap fan motor w/ blade Evap fan mounting shroud Hinged Cover (39") Hinged Cover (45") Hinged Cover (53") Hinged Cover (57") Hinged Cover (65") Hinged Cover support pin Support pin acorn nut Pan Rail Cover Filler (8.25") Pan Rail Cover Filler (5.
