FCC ID:A4C91005A ClearDryve 50 TM Support www.randmcnally.
Contents What’s in the box.................................................................................................................................................................... 2 Streaming Music................................................................................................................................................13 ClearDryve Parts...........................................................................................................................................
What’s in the Box In-box contents includes: ClearDryve™ Parts Microphone Head Band ClearDryve™ 50: • Earpiece Release .ClearDryve™ headphones • Audio cable • Charging cable • .Drawstring pouch • Detachable earpiece (comes pre-assembled to the headphones) • .Detachable headpad Mic Boom Arm Note: The earpiece release button is located on the inside of the headband. The detachable headpad (shown separately), is pre-assembled on the ClearDryveTM 50.
Function Button Layout The mic boom arm, ports, LEDs, and function buttons on the ClearDryve™ headphones are on the same earpiece. You can use this earpiece on either ear. ClearDryve™ automatically adjusts for either side when you extend the mic arm. To switch the earpiece with controls from one ear to the other, swivel the mic boom up and over to the other side. 1. .Vol + button 1 2. .Vol – button 3. .Micro-USB port 2 4. 3.5mm audio input 3 5. .Multi-function button (MFB) 4 7 6.
Getting Started with ClearDryve™ Power ClearDryve™ On and Off To get started using ClearDryve™, first you need to charge the battery. After you power it on, then you can pair ClearDryve™ to your Bluetooth® - enabled phone, tablet or laptop. Once ClearDryve™ is paired, you can immediately start taking and managing calls or listening to music. To turn ClearDryve™ on and off: 1. To power ClearDryve™ on, press the MFB. 2. You will hear “Power on.
Once a device is paired, the LED stays solid blue. ClearDryve™ will reconnect automatically when Bluetooth® is enabled and the device is within range. To pair ClearDryve™ with a BT device: 1. Power on ClearDryve™. 2. 3. 4. Enable Bluetooth® on your device. ClearDryve™ will display on your device as ClearDryve™ 50. Select it. The LED will change to solid blue. You can pair ClearDryve to a new device at any time by entering pairing mode again.
Answer an Incoming Call End a Call Redial the Last Number To answer an incoming call: To end a call: To redial the last connected number: 1. Press the MFB. 1. Press the MFB to hang up. 1. Quickly press the MFB twice. 2. ClearDryve will beep once to confirm. The call will be live immediately. 2. ClearDryve will beep once to confirm. 2. ClearDryve™ will beep once to confirm.
Turn the Volume Up and Down Streaming Music At any time, you can press the volume buttons to turn the volume of the call up or down. There are 16 different volume levels available. Quick Access To change the volume: 1. Press Vol + to increase the volume. 2. Press Vol – to decrease the volume. 3. ClearDryve™ will beep when you reach the lowest or highest volume settings. Note: Depending on your device, the volume buttons may behave differently.
Turn the Volume Up and Down Go to the Next/Previous Song Connect to a Wired Device At any time, you can press the volume buttons to turn the volume of ClearDryve™ up or down. To switch to a different song: You can connect ClearDryve™ to any standard 3.5mm audio aux jack. There are 16 different volume settings available. 1. Long-press Vol + to advance to the next song. 2. Long-press Vol – to go back to the beginning of the current song. Long-press again to go to the previous song.
EQ preset Your ClearDryve allows you to pick from 5 preset equalizer (EQ) settings. This allows you to pick the ideal settings for the specific type of music you are listening to. When you first turn on power to your ClearDryve, the first equalizer setting (EQ1) is active by default. Pressing the EQ button will result in EQ 2 becoming the active preset. Keep tapping on the EQ button to toggle through the presets till you find one that delivers the best sound quality.
Troubleshooting & FAQ Reset to Factory Settings You may need to restore ClearDryve back to its factory state, typically when switching over to newer model smartphones / laptops for daily use. Clearing the “pairing history” on your headphones can help improve connection times between your headphones and new devices. ™ To reset ClearDryve™: 1. Make sure ClearDryve™ is powered off. Now press and hold MFB to place it in pairing mode. 2. Press and hold Vol - and MFB at the same time until you hear 2 beeps.
Help and Support Warnings, End-User License Agreement, and Warranty WARNING: Safe Driving Practices Contact Rand McNally customer support for assistance: Never attend to or handle the headphones while driving. Always use your best judgment and exercise common sense when the vehicle is in motion and do not allow yourself to be distracted by the headphones while driving. Pull over in a safe and legal manner before attempting to attend to or handle the headphones.
Warranty Rand McNally warrants that the product and the component parts thereof, will be free of defects in workmanship and materials for a period of one (1) year from the date of purchase. This warranty may be enforced by the first consumer purchaser (“Customer”) only, provided that the product is utilized within the U.S.A. or Canada.
Federal Communication Commission (FCC) Radiation Exposure Statement The device has been evaluated to meet general RF exposure requirement, The device can be used in portable exposure condition without restriction Federal Communication Commission (FCC) Radiation Exposure Statement Power is so low that no RF exposure calculation is needed. This device complies with part 15 of the FCC rules.
