User manual

62
8.3. Heating a beverage
● Immerse the steam spout into the liquid to be
heated.
● Gradually turn on the steam tap 6 (Fig.8); the
steam that bursts in the liquid heats it to the desired
temperature.
● Turn off the steam tap when the desired tempera-
ture has been reached.
Immediately after carrying out this operation,
clean the spout with a sponge or clean cloth.
Be careful as the spout is hot and may burn
your hand.
7 Make the coffee and check the cup amount in
order to check that programming is correct.
If some doses have to be changed (A-B-C-D), once
at point 5 repeat the instructions in points 3-4-5 for
each dose, remembering to use the lter-holder with
relevant lter and freshly ground coffee.
Then carry out point 6 and repeat point 7 to check
all changed doses.
If all units are to be programmed with the same
doses, the selection of coffee doses is nished. If
the dosage of another unit is to be changed (1-2-3-4
doses), proceed as indicated in the above-mentio-
ned point 1-7, using only the button panel of the
selected unit.
9.1.2. Adjusting the quantity of hot water
Proceed as follows:
1 Press the continuous
E button on any button panel
and hold down for 8-10 seconds until water stops
owing from the dispensing unit and the led of the
E button on the rst button panel on the left starts
ishing. The machine is ready to accept quantity
variations.
2 Put a cup or a jug to receive the water under the
water spout 16 (Fig.3).
3 Push the delivery button 5B
4 Once the required amount is reached, press the
button 5B again. Water will stop pouring and the
5 Once adjusted, press the stop-continuous button
E on any button panel; the led will go out and the
machine will store the new quantity.
6 Pour out doses of hot water to check that pro-
gramming is correct.
WARNING!
The amount of hot water dispensed can be controlled
by proceeding as follows:
● press the hot water control button 5A or 5B and
hold down for at least 2 seconds; when the but-
ton is released, the machine will dispense water
continuously.;
● to manually stop dispensing, press the water
control button 5A or 5B again when the required
amount has been dispensed.
To stop dispensing the measured amounts of hot
water, press the water control button 5A or 5B.
9.2. Tray case assembly (Fig.10)
The machine is provided with two lateral housing to
be applied to the tray group if the available space
does not allow, during installation, to install the ma-
chine in standard version.
To replace the cases installed on the machine, un-
screw the 3 screws (Fig.10), remove the right case
and replace with the one having smaller dimensions.
In the same way replace the left case.
8.4. Preparing tea, camomile, etc.
● Place the jug under the hot water spout and use
the delivery control according to the model (Fig.8).
When the desired quantity has been obtained, turn
off the switch.
● Add the beverage desired.
Models E
For these models, hot water is dispensed in specic
measures (see paragraph 9, adjusting the dose of
hot water).
When puried water is used, these beverages often
assume a darker colour.
Should the user prefer a lighter coloured drink, draw
fresh water from an ordinary tap and proceed with
the heating phase as described in point 8.3.
9. ADJUSTMENT AND SETTING OF THE
DOSE
9.1. Models E (Fig.8)
It is possible to adjust the dose of coffee and hot water
dispensed by electronically controlled models. (If the
function is enabled)
9.1.1. Adjusting the dose
The quantity of coffee and hot water dispensed can
be adjusted using the button panel or the hot water
controls.
1 Press E on the rst push-button panel for 8-10
seconds seconds until water stops owing from
the dispensing unit and the led of the continuons
button on the rst button panel on the left begins
ashing.
2 It is necessary to act as to make 1 or 2 cups in or
-
der to reach the correct coffee amount adjustment
in the cup.
3 Put the lter-holder (with ground coffee) on the left
unit and the cup under the spout.
4 Operate the selected button (i.e. button A for one
small cup).
5 One the required coffee amount in the cup has been
reached, press the stop button A. Coffe will stop
pouring and the microprocessor will store the dose.
6 Press the continuous button E again; the led will go
out and the machine will store the new quantity.