Instruction manual
87
TKHSULPDU\DLULQWDNHUHJXODWRULVVHWZLWKWKH
reference notch showing “GPL” corresponding te the
secuting screw (3).
7KHÀDPHLVUHJXODWHGPLQLPXPDQGPD[LPXPWR
VXLWWKLVW\SHRIJDV
,I WKH PDFKLQH LVWR EH XVHG ZLWK D GLIIHUHQW W\SH
RIJDVLWZLOO EH QHFHVVDU\ WRUHSODFH WKHLQMHFWRU
in accordance with the above table and to rotate
WKHSULPDU\DLUUHJXODWRUZKLFKLQWKHFDVHRI
natural gas, will have to be set with the reference
notch showing “N” corresponding to the securing
screw (3).
7RGRWKLVLWZLOORIFRXUVHEHQHFHVVDU\WRORRVHQ
the securing screw (3) and to tighten it again after
URWDWLQJWKHSULPDU\DLULQWDNHUHJXODWRU
Connections to mains gas, from the gas tap available
LQWKHURRPWRWKHYDOYH¿WWHGRQWKHPDFKLQHPXVW
be carried out in accordance with the regulations in
IRUFHXVLQJDÀH[LEOHSLSHRUDULJLGSLSHLQDQQHDOHG
copper.
,QWKHODWWHUFDVHWKHVSHFLDOUXEEHUSLSH¿WWLQJLQ
FRQQHFWHGWLJKWO\WRWKHYDOYHE\PHDQVRIWKHELFR-
nical nozzle and securing nut supplied.
7KHÀH[LEOHSLSHLV¿WWHGRYHUWKHHQGRIWKHPDLQV
outlet and secured with the metal strip supplied.
$OWHUQDWLYHO\WKHDQQHDOHGFRSSHUSLSHFDQEHFRQ-
nected up, again using the special biconical nozzle
DQGWKHDSSURSULDWHQXWVGLUHFWO\WRWKHYDOYH
Once the machine has been connected up to the
JDVPDLQDQGDIWHU¿OOLQJWKHERLOHUXSZLWKZDWHULQ
accordance with the instructions in the booklet (“IN-
STRUCTIONS FOR USE AND MAINTENANCE”),
the burner can be lit in the following manner:
L Open the main gas tap.
L Press on the gas valve knob, on the machine rotate
it 90° anti-clockwise, and keep it pressed in. At
the same time, press the piezoelectric lighter one
RUPRUHWLPHV±WKHOLJKWHUNQREEHDUVDV\PERO
resembling a spark – until the burner lights up.
L Wair about 20 seconds, then release the valve
NQREDQGWKHEXUQHUVKRXOGVWD\OLW±WKHÀDPHLV
vidible through the special hole in the panel behind
the dispenser units.
1%
Should the burner not light up, do not persist, but
release the valve knob, and then check that lighter
spark on the burner is in order and about 5 mm
ORQJ
6KRXOGWKHÀDPHJRRXWZKHQWHYDOYHNQRELVUH-
leased, check the position of thermocouple and the
FLUFXLWFRQQHFWHGWRLW
7KHÀDPHVKRXOGEHEULJKWEOXHLIQRWVOLJKWO\UHJX-
ODWHWKHSULPDU\DLULQWDNHXQWLOWKHGHVLUHGHIIHFW
is achieved.
Wait until the machine has the correct pressure,
according to instructions. Otherwise, adjust the gas
pressure regulator, which has two regulating screws.
The one that protrudes more (4) serves to regulate
the boiler’s operating pressure, while the other (5)
VHUYHVWRVHWWKHÀDPHDWWKHPLQLPXP
When the machine is pressurized, check to see
WKDWWKHPLQLPXPÀDPHLVFRUUHFWE\DGMXVWLQJWKH
VFUHZLIQHFHVVDU\DIWHUORRVHQLQJWKHORFNLQJ
nut, unscrew the screw until it feels loose (the main
gas-pipe is closed), and check whether, under these
FRQGLWLRQVWKHORZÀDPHUHPDLQVOLWWKXVDFWLQJDV
a pilot.
,IWKHÀDPHLVWRRKLJKLWZLOOEHQHFHVVDU\WRUHJXODWH
VFUHZWXUQLQJLWVOLJKWO\FORFNZLVHRIFRXUVHDIWHU
KDYLQJORRVHQHGWKHORFNLQJQXW,IRQWKHFRQWUDU\
WKHÀDPHWHQGVWRJRRXWWKHQUHJXODWHVFUHZE\
WXUQLQJLWDQWLFORFNZLVHXQWLODYHU\ORZEXWFRQVWDQW
ÀDPHLVREWDLQHG+DYLQJDFKLHYHGWKLVFRUUHFWDGMX-
VWPHQWRIWKHPLQLPXPÀDPHKROGWKHVFUHZVWLOODQG
lock it with the locking-nut.
Then rotate the screw (4) clockwise until there is a
WKHUHLVDKLJKÀDPHDQGZDLWIRUWKHERLOHUWRUHDFK
WKH GHVLUHG RSHUDWLQJ SUHVVXUH LI WKH ÀDPH GLHV
down before reaching the required pressure, tighten
VFUHZIXUWKHULIWKHÀDPHGLHVGRZQDWDKLJKHU
pressure, then unscrew the screw.
&KHFNRQFH RUWZLFHE\RSHQLQJ WKHVWHDPWDSWR
release the pressure in the boiler, then hold screw
(4) still and lock it with the locking-nut.
0$&+,1(6:,7+$/7(51$7,9(*$6
+($7(59(56,21(Fig.14)
N.B. Installation of the machine and any
adjustment or adaptation to the type of gas
VKRXOG EH GRQH E\ D WHFKQLFDOO\ TXDOL¿HG
SHUVRQ
7KHPDFKLQHOHDYHVWKHIDFWRU\DOOVHWIRUXVHZLWK
liquid gas (GPL).
7KHJDVUHJXODWRULVWKHUHIRUH¿WWHGZLWKWKHDS-
propriate injector shown in the table below:
Model
Nominal
thermic
FDSDFLW\
GPL
G30 - 29 mbar
(cent of milimeter)
Natural gas
G20 - 20 mbar
(cent of milimeter)
2 Gr.
2,5 KW
(2150 Kcal/h.)
75 102
3-4 Gr
3,3 KW
(2850 Kcal/h.)
90 135