SN/RAM 6000 & RAM 9000 Software Manual v5 Firmware Version 3.20/4.20 www.redlion.
Chapter 1 1.1 1.2 Connect PC to Red Lion Router. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Setup PC IP Address. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 1.2.1 1.2.2 1.2.3 1.2.4 1.2.5 1.2.6 1.2.7 1.3 Chapter 2 Chapter 3 Web User Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Organization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.5.2 3.5.3 3.5.4 3.5.5 3.5.6 3.5.7 3.5.8 3.5.9 3.5.10 3.5.11 3.5.12 3.6 Automation Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127 3.6.1 3.6.2 3.6.3 3.6.4 3.6.5 3.6.6 3.6.7 3.7 DHCP Relay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97 Dynamic DNS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connect PC to Red Lion Router Chapter 1 Accessing the Web User Interface 1.1 Connect PC to Red Lion Router Connect a CAT-5 or CAT-6 Ethernet cable between the local PC and the Red Lion router’s Ethernet Port(s). Note: If the Ethernet port’s green LED is lit, this indicates that the connection is running at 100Mb speed. If the Ethernet port’s green LED is not lit, this indicates that the connection is running at 10Mb speed. The yellow LED indicates the “link” status of the connection.
Setup PC IP Address 1.2 Setup PC IP Address 1.2.1 Open the Control Panel • Click on Start and browse the “Control Panel” menu item. The Control Panel should look similar to the following: 1.2.
Setup PC IP Address 1.2.3 • • Access Network Connection Settings Click on the link to access network connection settings. • XP - “Network Connections” • Vista/Windows 7 - “Network and Sharing Center” The display should look similar to the following: 1.2.4 • • Access Local Area Connection Click on the link to access the local area connection.
Setup PC IP Address 1.2.5 Open Properties • Click on “Properties” button (Vista/Windows 7 will display a popup window asking to confirm the operation). • Click on the “Continue” button. The display should look similar to the following: 1.2.6 • • Access Internet Protocol Properties Click on the Internet Protocol to highlight. • XP - “Internet Protocol (TCP/IP)” • Vista/Windows7 - “Internet Protocol Version 4 (TCP/IPv4)” Click on the “Properties” button.
Setup PC IP Address METHOD 1: PC to: WAN /ETH0, Ethernet on SN/RAM-6000, RAM 9000 • Select “Use the following IP address” and fill in the blank fields with the information below: •IP address:192.168.0.2 •Subnet mask:255.255.255.0 •Default gateway:192.168.0.1 •Preferred DNS:192.168.0.1 • Click “OK”. • The previous screen will appear. • Click “OK”.
Setup PC IP Address METHOD 2: PC to LAN: ETH1, RAM 9000 Series only • Select “Use the following IP address” and fill in the blank fields with the information below: •IP address:192.168.1.2 •Subnet mask:255.255.255.0 •Default gateway:192.168.1.1 •Preferred DNS:192.168.1.1 • Click “OK”. • The previous screen will appear. • Click “OK”. Verify that you are connected to the router. • Open a Command Prompt window on your laptop. • XP Start Run, type in cmd and press the ENTER key.
Setup PC IP Address METHOD 1: PC to WAN /ETH0, Ethernet on SN-6000, RAM 9000 Type in ping 192.168.0.1 and then press the ENTER key The display should look similar to the following: METHOD 2: PC to ETH1: LAN on RAM 9000 only Type in ping 192.168.1.1 and the press the ENTER key The display should look similar to the following: This shows the connection is up and functioning. 1.2.
Setup PC IP Address • Right-click on the USB Ethernet/RNDIS Gadget adapter, and select Update Driver Software. • Select Browse my computer for driver software: • Select “Let me pick from a list...
Setup PC IP Address • Uncheck the “Show Compatible Hardware” check box. In the Manufacturer box, browse to Microsoft Corporation. Then select “Remote NDIS Compatible Device” in the Network Adapter box. Click Next. • The “Update Driver Warning” dialog window shown below will appear. Click on Yes. • Once the install is complete, click on Close. • The USB Ethergadget driver should now be loaded and you should be able to access the Red Lion device via USB/ Ethernet at 192.168.111.1:10000.
Access Red Lion Web Server 1.3 • • 1.3.1 Access Red Lion Web Server Open a web browser and enter the following in the address bar: METHOD 1 (WAN/ETH0): http://192.168.0.1:10000/ METHOD 2 (LAN/ETH1): http://192.168.1.1:10000/ METHOD 3 (LAN/ETH1): http://192.168.111.1:10000/ You will receive a login pop-up screen.
Access Red Lion Web Server If the ppp0 or wwan0 interface do not show an IP address, this could indicate that the internal SIM/Module has not been properly activated. Low or invalid signal strength may also contribute to the issue. Please contact your service provider to ensure proper activation. You may need to enter provisioning information in the NetworkingCellularProvisioning screen. Consult Section 2.1 for more information. 1.3.
Cellular Configuration Chapter 2 Cellular Connections 2.1 Cellular Configuration Cellular connectivity can be obtained through the use of an internal (embedded) RF Module. Your Red Lion router has an embedded cellular radio that is already detected and configured for the intended carrier. If you are using a carrier that supports the use of an APN, you may have to set your specific APN manually, as covered in the next section.
Cellular Configuration Activation Status column: See table below for a description of the different statuses found in the “Activation Status” column. CDMA HSPA/LTE Running - Connection/Activation is running Not Reg - Modem not registered Waiting - Connection/Activation tried and failed. Will retry in 20 mins.
Cellular Configuration 2.1.3 Provisioning For Sprint/CDMA installations for Sprint Data link support, additional information may be required. Navigate to Network -> Cellular Connection -> Provisioning. 2.1.4 Verify Cellular Connectivity Browse to the Status screen, by selecting Summary -> Status. The following dialog window will appear: As shown, the router is receiving good signal from the cellular network, it is connected and has been issued an IP address.
Cellular Configuration NOTE: Depending on the provisioning of your module/SIM, particularly in corporate applications in which the unit is providing cellular backup connectivity to wired circuits, your module/SIM may be restricted from Internet access. If this is the case, you may want to test to ensure that you are able to access your corporate network. If you have any questions about your configuration, please check with your network administrator.
Cellular Configuration 2.1.5.2 Verifying IP Connectivity First, check to make sure that your device is connecting to the cellular network and obtaining an IP address. Navigate to the Web UI Status screen shown below: If your screen looks similar to the one shown above, you are having signal reception difficulties. You can further verify this condition by examining the LED signal meter.
Cellular Configuration OFF No signal available or signal strength is below -100 dBm ON Excellent signal strength = greater than -69 dBm Signal Fast: Every 300ms = -79 to -70 dBm FLASH Medium: Every 600ms = -89 to -80 dBm Slow: Every 1200ms = -99 to -90 dBm RAM 9000 units: Observe the RSSI LED as shown below. Low Signal / No service > - 109 dBm (Low but valid signal) RSSI > - 99 dBm (Lower but valid signal) > - 89 dBm (Avg signal) > - 80 dBm (Excellent signal) 2.1.5.
Cellular Configuration If you refresh this screen every few minutes and notice that the IP address is changing frequently, it is possible that the router is connecting to the network and obtaining an IP address and then the connection to the cellular network is being dropped. When the connection is re-established, the device is then issued a different IP address. 2.1.5.
Web User Interface Introduction Chapter 3 Web User Interface 3.1 Web User Interface Introduction 3.1.1 Organization The Red Lion Web UI is comprised of six major sections. (Click on a link to get an in-depth description of each topic) • Status: The Status tab presents information on the router. This tab is organized into five (5) sections: Summary, Network, Diagnostics, Syslog and Gather Stats.
Status Tab 3.2 Status Tab The Status Tab allows you to review the state of the router functions, such as network connections, interfaces, system processes, services running, and system information. It also allows review of the syslog, update history, and under diagnostic tools, permits testing connectivity through the use of ‘ping’ and ‘traceroute’. 3.2.1 Summary This option will return the user to the System Summary (home) page.
Status Tab 3.2.2 EZ Config Wizard The EZ Config Wizard is used to setup your Ethernet IP without having to navigate through multiple dialog windows. The EZ Config Wizard is situated on the Summary page and accessed by clicking on the blue EZ Config Wizard button. • Click on the EZ Config Wizard button. The Eth0 Settings dialog window will open: Enable eth0 Interface: Select Yes to enable the interface or No to disable it. If you select No, the fields below the “Enable eth0 Interface” will disappear.
Status Tab Recommended Setting: This address should have been provided by your Network Administrator. It must be an address valid for the network described by the value contained in the Enter Subnet Mask field and must not conflict with any other device on the target network. Enter Subnet Mask (Required): Enter the desired Netmask for the interface. This field is only available when “Obtain Network Addresses via DHCP” has been set to No.
Status Tab • Once the desired settings have been entered, click on the Finish button and a recommendation dialog window will appear. • Click on Revert, Save or Apply (see explanation of each setting in dialog window above). 3.2.3 Network The Network menu contains the following sub-menus: Arp Cache, Firewall Rules, Interfaces, Routing Tables, Socket Statuses and Traffic. 3.2.3.
Status Tab 3.2.3.2 Firewall Rules The “Firewall Rules” menu item displays a complete listing of the rules used within the firewall for the Red Lion router. If you are familiar with Linux and IPTables, this will be of great use. Scroll through the list of rules to review the entire IPTABLES listing. This information is used to track traffic being allowed and traffic being denied access to and through the Red Lion router. 3.2.3.3 Interfaces The “Interfaces” dialog window is divided into three sections.
Status Tab The “Multicast” table displays the current multicast settings for various interfaces. 3.2.3.4 Routing Tables The “Routing Tables” dialog window contains both the Standard System Routing Table and the Policy Routing Table. The “Standard System Routing Table” displays the current routes for the Red Lion router and the static routes that have been configured for the router.
Status Tab The “Socket Statuses All” table displays the sockets that are considered connection-oriented and connectionless (also known as “datagram sockets”). 3.2.3.6 Traffic The Traffic dialog window shows the unit’s traffic history. From the Display Flag drop-down list, select which information is desired and which Interface is to be viewed. The information will then be shown on the dialog window.
Status Tab 3.2.4 Diagnostics The Diagnostics menu is sub-sectioned into Status, Ping, Socket Test, Traffic Capture, Socket Test, Traceroute and System Info submenus. These are useful in troubleshooting connectivity of the Red Lion router to the Internet or the Network the router is connected to. 3.2.4.1 Cellular Status The Status menu item will bring up a dialog window which displays the status of the cellular connection.
Status Tab 3.2.4.2 Ping The Ping menu item allows you to input an address either as an IP Address or a URL for testing the destination availability. Host/IP Address field: Type in the IP Address or URL you wish to Ping. It is recommended you start with a locally accessible IP address to confirm communication to an interface’s local subnet. Then proceed to addresses on distant networks. Your local default gateway is a good test, and this IP can be found in the your routing table.
Status Tab 3.2.4.3 Traffic Capture Traffic Capture will use the tool tcpdump to perform network traffic captures and generate a widely compatible .cap file. A series of rotating capture files will be generated to prevent exhausting local resources and all may be downloaded for post-capture analysis in the viewer of your choice. Capturing the most relevant information may require trial and error to obtain the best filter for specific investigations.
Status Tab 3.2.4.4 Socket Test The Socket Test menu item will allow you the “Telnet” to desired destination IP and Port addresses to verify the socket availability. Host/IP Address field: Type in the IP Address or URL you wish to connect to via Telnet. Destination Port field: Enter the Destination IP Address of the server to which you would like to connect. • 3.2.4.5 Click on the Test button at the bottom of the dialog window to proceed with the TCP socket test to verify socket availability.
Status Tab 3.2.4.6 System Info The System Info menu item will display the current usage of the file system in both the directory size and the memory utilization. 3.2.5 Syslog The Syslog window will display the current log into the syslog of the Red Lion router.
Status Tab Filter String (optional): Enter a filter string in the space provided. Only lines containing the filter value(s) will be displayed via a GREP (Global Regular Expression Parser) style filter mechanism. Auto Update: Select YES to enable automatic updating of the log file display. The update interval can be selected using the Select Update Interval option provided in the field below the Auto Update one. Manual updating is disabled while auto update is in effect.
Status Tab Include All Network Files: Select YES to include all networking related configuration files. If using “gatherconfigs” to clone a unit, note that this option will cause the network interfaces (Including static IP addresses) to be cloned as well. If performing a gatherconfigs for review by Technical Support, please choose YES for this option. • To create the files for the Stats and/or Configs, click on the Generate Stats and/or Generate Configs buttons.
Admin Tab 3.3 Admin Tab The Admin Tab is where you configure web access methods, manage SSL/IPSEC certificates, set passwords, update firmware, manage configurations and set factory defaults. 3.3.1 Access Settings The “Access Settings” menu item allows you to change how the unit’s Web UI is accessed, either by HTTP or HTTPS. You can also change the passwords used to access the Web User Interface.
Admin Tab User: admin (Full access) New Password: Enter the new password in the “New Password” field. Note: For a secure password, choose one that is at least six characters long, which is not a common word and comprised of a mixture of upper and lower case characters and numbers as well as special characters. Please note that the single quote (‘) character is not a valid character. For security purposes, it is recommended that the admin password be changed according to your internal policies.
Admin Tab Time Zone: Select the time zone corresponding to your geographical location by choosing one of the values available on the drop down list provided. To configure the date and time for your Red Lion router there are three options: Option 1: Sync to NTP Server: Select Yes to enable synchronizing the system clock to an NTP server. Option 2 - Manual Configuration: Current Date (MM/DD/YYYY) (Required): Set the Sync to NTP Server field to No and enter the Current Date using the shown format.
Admin Tab To create a new certificate: • Click on the Add button and the following dialog window will appear: Name: Enter a descriptive name to be associated with the Certificate File to be uploaded. This name will be used later in fields where selection of a certificate is required. The descriptive name can contain only upper and/or lower case letters and digits. Type: Select the type of certificate that you will be uploading.
Admin Tab • Click on the Finish button and you will be directed to the Certificate Manager dialog window and the table will be populated with the entered data. • To delete an existing rule, select it in the table and click on the Delete button. To edit an existing rule, select it in the table and click on the Edit button.
Admin Tab To upgrade the firmware of the Red Lion router: Boot Image File: Select the file that will perform the Kernel update. Root Image File: Select the file that will perform the system update. Preserve current configuration: Select YES to save the device’s current configuration and restore it after the firmware image is installed. • Click on the “Install” button. Note: This procedure could take anywhere from 6-10 minutes to complete.
Admin Tab Export Web UI Master Configuration File: To save a copy of the Red Lion router configuration, click on the “Export” button. The pop-up window below asking you to save or open the file will appear. Select the desired option. Note: Please note the directory where the file was saved in order to retrieve it when needed to put the file back onto the Red Lion router. Import Web UI Master Configuration File: Set your importing defaults for the configuration file.
Admin Tab 3.3.4.2 Package Installation The Package Installation feature allows you to upload and install patches from Red Lion. • Click on the Package Installation menu item and the following dialog window will appear: • In the Package File field, click the Select File button, and the following dialog window appear: • Browse to the directory where the patch is located. • Select the filename to select the file. Note: Be sure to use only genuine Red Lion provided packages in the form of filename.
Admin Tab 3.3.4.3 Factory Defaults/Reboot The Factory Defaults/Reboot menu item allows you to restore the configuration back to factory default settings. • Click on the Factory Defaults/Reboot menu item and the following window will appear: Restore Factory Default: Click on the Restore button to restore the factory default settings. A warning will appear, read through the information and click OK. The restore may take 2-5 minutes. Reboot System: Click on the Reboot button to reboot the device.
Admin Tab 3.3.4.4 Job Control The Job Control feature is used to create jobs that will be run at specified intervals. • Click on the Job Control menu item and the following dialog window will appear: Predefined Job Settings: Predefined Job Interval: Select the appropriate periodic job interval from the drop-down list provided to run at the scheduled job interval. If the option Disabled is selected, all the jobs created for the selected job will be removed.
Admin Tab Weekly: WIll run at 4:22 am, every Sunday. Monthly: Will run at 4:42 am, on the first day of every month. Upload Script File: Click on the Select File button to browse to the location where the job to be uploaded is stored. • Click on the Import button once the file is selected. Delete Imported Job Script: Select Imported Job: Select an imported job from the drop-down list to be deleted from any scheduled job interval. • Click on the Delete button once the job to be deleted has been selected.
Network Tab 3.4 Network Tab The Network Tab configures aspects of the Red Lion router affecting the networking functionality of the unit. From here you can configure the Cellular Connection (should the air card/SIM not be recognized at power up), Ethernet Interfaces, Firewall, Tunneling, DNS Settings, Static Routes and TCP Global Settings. 3.4.1 Cellular Connection The Cellular Connection menu item is sub-sectioned into Configuration, Status and Provisioning.
Network Tab Enable Interface: Select Yes to enable the interface to become active after the new settings are applied and upon subsequent system start-up. Select No to disable the cellular interface and prevent the cellular radio from attempting to establish a network connection. Select APN Context: Select the desired APN Context from the provided drop-down. This information should have been given to you by your service provider when service was established.
Network Tab Use WWAN for LTE: This option will convert non Verizon, SN/RAM 67xx and 97xx units, to a new wwan0 interface. Significantly improved transfer speeds will be available. If some special circumstance requires continued use of ppp0, this option may be disabled, but slower speeds may result. The recommended setting for this field is YES. Select Cellular Network Speed: Select the connection speed to be used for the cellular modem connection from the drop down list provided.
Network Tab Normally recommended for a wireless interface which has a static IP (never changes). Can sometimes cause problems with dynamic IPs. The recommended setting for this field is NO. Enable Custom AT and PPP Commands: Custom AT and PPP commands are for advanced users and configuration. This option should not be enabled or used except under the direction of Red Lion Technical Support. Enabling and entering items into this option can cause your Cellular modem’s connection to fail.
Network Tab 3.4.1.3 Provisioning The Provisioning menu displays carrier specific information that may be useful when initially provisioning your device with a new carrier. • Click on the Provisioning menu item. If a cellular connection is found, the following window will appear with the information about the modem in the upper window: Note: If the cellular SIM is not recognized, go to the Configuration dialog window and enter the required data (see section 3.4.1.1).
Network Tab 3.4.2 Interfaces The Interfaces menu allows the administrator to configure the Ethernet ports of Red Lion routers to incorporate within their existing network topology. Interfaces available may include eth0 (WAN), eth1 (LAN), Wifi, USB and IPv6. These will only be present if your hardware supports these interfaces. These ports are ‘auto-sensing’, allowing for greater flexibility. 3.4.2.
Network Tab Select No to prevent the interface from obtaining address information via a DHCP server. You will be required to enter an IP address, netmask and remote gateway addresses. DNS information can be provided by navigating to Network -> DNS Settings. Enter IP Address: This field appears when No is selected for “Obtain Network Addresses via DHCP”. Specify the IP Address to be assigned to the Ethernet port when a ‘Static’ IP Address configuration is selected.
Network Tab with any other device on that network with a range of addresses of 192.168.1.1 through 192.168.1.254 (with 192.168.1.255 reserved for broadcast). An address outside of that range is on a different network which would need to accessed indirectly through a router and that router would be the gateway to the network on which the remote target device resides, so to communicate with it would mean sending and receiving via the gateway device.
Network Tab Enter Netmask (Required): This field specified the netmask to be assigned to the sub interface. You Network Administrator should be able to provide an appropriate value. • Click on the Finish button and you will be directed to the Ethernet Interface dialog window and the Interface Aliases table will be populated with the entered data. Interface VLANs: Sub-interfacing is essentially the segmenting of a single wire, or port, into multiple IP networks.
Network Tab • Click on the Finish button and you will be directed to the Ethernet Interface dialog window and the Interface Aliases table will be populated with the entered data. Reboot: Will restart the system and apply all the settings upon reboot. Revert: Will revert the settings in the dialog window back to the previous saved settings. Save: The interface will not be activated or deactivated until the device is rebooted.
Network Tab 3.4.2.2 Wi-Fi (WLAN) - (RAM-9631 and RAM-9731 only) The Wi-Fi interface option is used to configure the parameters for wireless LAN clients which may connect to the Access Point. From this option, the administrator may change wireless encryption settings as well as wireless network parameters. The RAM-9x31 unit’s Wi-Fi capability is enabled by default. The factory default configuration will setup the following parameters: SSID: ModelNumber - Last 6 digits of the Wi-Fi MAC addr.
Network Tab Wi-Fi LAN Interface Enable WLAN Interface: Select YES to enable the Wi-Fi interface. Wireless Mode: Select “Access Point” if clients will connect to this device to obtain an address or “Client” if this device will be connecting to a network with another device acting as the access point. Most users should choose “Access Point” here. IP Address (Required): The wireless bridge IP Address is entered in this field. The IP Address identifies a device on the TCP/IP network.
Network Tab Encryption Mode: This option allows you to setup the wireless security. If security is disabled, any client can connect to the Access Point. Turning on WPA requires clients to know an encryption key before connecting to the network. WPA Pre-Shared Key (Required): This option is available when WEP or WPA is selected as an option for Encryption and allow the user to specify the encryption key to be used. For WEP, this should be a 26 digit hexadecimal value.
Network Tab The IP address should have been provided by your Network Administrator. It must be an address valid for the network described by the value contained in the Enter Subnet Mask field and must not conflict with any other device on the target network. Enter Subnet Mask: Enter the desired Netmask for the interface in the field provided. Your Network Administrator should be able to provide an appropriate value.
Network Tab WAN Interface: Specify the IPv6 Upsteam Router path. If a unit has access to a real IPv6 router on multiple interfaces, you may specify it here. Cellular devices expect that the wwan0 interface will lead to the IPv6 routers. Wired Routers will expect that eth0 (default untrusted/external interface) may also lead to an upstream IPv6 router. LAN Interface: The Router Advertisements are available for one of 64 subclass on one local LAN interface.
Network Tab Warning: When enabling switch mode, current ethernet settings (eth0) will apply only to the single WAN port. On the front of the unit, this may be shown as under the power connector. The remaining four ports will be configured as a LAN (eth1). Please check your Ethernet connections to make sure that the new settings will not conflict with previous network configurations.
Network Tab Select ttyS Port: Select the ttyS port on which the modem is attached. For an external modem connected to a serial port, use the port name as labeled on the unit. For an internal modem, a common setting is ttyS3. Enter Dial String (Required): Enter the phone number of the peer/ISP to dial. Enter User Name (Required): Enter the name used for authenticating the local system to the peer. Please consult your ISP for these values.
Network Tab 3.4.2.7 PPP over Ethernet The PPP over Ethernet menu item is used to configure a connection by being able to connect a DSL or cable modem. • Click on the PPP over Ethernet menu item and the following dialog window will appear: Enable PPPoE: Select Yes to enable the PPP over Ethernet service on the specified interface when the Apply button is clicked. To disable the service, select No and click Apply.
Network Tab Use Custom DNS: DNS information is entered manually in the fields which will appear below. Use Default Route: Select Yes to use this interface as the default route. Dial on Demand: Select Yes to enable this feature. The recommended setting for this field is No. • 3.4.3 Click on the “Save” button for changes to be saved without activating the interface, the “Apply” button will save your settings and apply them immediately. To revert to the previous defaults, click on the “Revert” button.
Network Tab Enable Firewall (Required): Specify whether to enable the firewall service on this device. The recommended setting for this field is Yes. Note: Disabling the firewall will compromise security and routing functions of the unit. Ping: To allow ICMP echo responses (Ping) from external devices through untrusted interfaces on this unit, select Yes; otherwise select No. The recommended setting for this field is Yes.
Network Tab Modbus Whitelist Name: Select the desired whitelist for the drop-down menu. Whitelists are created in the Network>Firewall>ACL Rules> Subnet Whitelist Rules screen. DNP3: To allow external devices to connect to the DNP3 Server, via port 20,000, through untrusted interfaces on this unit, select Yes; otherwise select No. The recommended setting for this field is No.
Network Tab IPSec/NAT Allow IPSEC: Specify whether to allow ESP data, as well as UDP port 500 to communicate with external devices through untrusted interfaces. The recommended setting for this field is Yes. Note: This is necessary if you are planning to configure any IPSEC tunnels originating from this device. Allow NAT-Traversal (Required): Specify whether to allow data on UDP port 4500 on untrusted interface. The recommended setting for this field is Yes.
Network Tab Untrusted Interfaces: Identifies the Primary Untrusted (external) Interface and the following pop-up window will appear: • Click on the Add button for Untrusted Interface and the following pop-up dialog window will appear: Interface: Choose an interface from the drop-down list provided. You may add any number of interfaces, up to as many exist on the device. Each selection must be unique. Untrusted interfaces will block all incoming traffic from devices/networks connected to this interface.
Network Tab 3.4.3.2 ACL Rules - Firewall Access Control List Rules From the ACL Rules dialog window, Whitelist and Blacklist rules are defined. Whitelist Rules are used to define a single IP Address or an entire network that would be allowed to access the network behind the Red Lion router. Blacklist Rules are used to define a single IP Address or an entire network that are NOT allowed to access the network behind the router.
Network Tab Enter Subnet (Required): Enter the network allowed to make connections to the above port(s), using IP/CIDR notation. To allow data from any source, enter 0.0.0.0/0. To specify a single host, use x.x.x.x/32, where x.x.x.x is the host’s IP address. • Click on the Finish button. You will be returned to the Firewall Access Control List (ACL) Rules dialog window and the Subnet Whitelist Rules table will now be populated with the recently entered data.
Network Tab • Click on the Add button and the following dialog window will appear: Inbound Interface: Select an interface associated with the Source Address/Subnet from the drop-down menu. Source Subnets via Whitelist: Select a whitelist name for the list of names available in the drop-down menu. Whitelists are defined in the Network>Firewall>ALC Rules>Subnet Whitelist Rules screen. Outbound Interface: Select the interface associated with the Destination Address/Subnet.
Network Tab 3.4.3.3 Masquerade/NAT/DMZ Rules DMZ rules are used to configure rules to route through a Demilitarized Zone (DMZ), Masquerade rules are used to configure an interface to give all IP Addresses on a local network access to the internet, while NAT(Network Address Translation) rules provide access to the Internet through a single machine that translates the IP addresses.
Network Tab NAT (Network Address Translation) Rules: The NAT Rules enables access to the Internet through a single machine that translates the IP addresses. The NAT itself has one or more IP addresses, but all the machines behind the NAT have ‘private’ Internet addresses. One-to-One NAT will perform a complete forwarding of app ports on the Original Destination IP to a new IP address entered in New Destination.
Network Tab Select Protocol: Choose the protocol type for this port’s data. Options are TCP, UDP, All. Source network via Whitelist: Select a whitelist name from the list of names available in the drop-down list box provided. Whitelists may be viewed/defined via the Network/Firewall/ACL Rules screen. • Click on the Finish button. You will be returned to the Masquerade/NAT/DMZ Rules dialog window and the NAT Rules table will now be populated with the recently entered data.
Network Tab New Destination Address Start (Required): This field is used to hold the starting range of real LAN IP of the destination device behind this router. One-to-One NAT Range will perform the same operation as a single One-to-One Rule, but over a range of matched IP Addresses. The pool defined by the Original IP Start->End, will be matched to the pool defined by New IP Start-> End (the first Original IP will always translate to the first New IP, the second to the second, etc.).
Network Tab DMZ Rules DMZ rules are used to configure routes through a Demilitarized Zone (DMZ). To add a DMZ host rule: • Click on the Add button and the following dialog window will appear: Select Interface: Click on the pull down-down menu to choose an interface that will be forwarded to a DMZ Host. All incoming packets (TCP/UDP/ICMP/etc) will be forwarded to the DMZ Host specified.
Network Tab 3.4.3.4 Port Allow/Forwarding Rules The Firewall Port Forwarding is used to configure routes from a small range of IP Addresses or all IP Addresses through one or more interfaces to a designated IP Address located behind the Red Lion router. Service Access (Allow) Rules: The Service Access Rules option is used to define what ports, either as a single port or a range of ports, are authorized access through the firewall on the Red Lion router.
Network Tab Interface: Select the interface on which this port will be opened. Incoming connections to this interface will be allowed into the device. Note: For connections destined to a device beyond this unit, use Host Redirect, NAT or DMZ rules instead. Select Protocol: Choose the protocol for the type of data you want to allow. Source Network via Whitelist: Select a whitelist name from the list of names available in the drop-down list.
Network Tab • To delete an existing rule, select it in the table and click on the Delete button. To edit an existing rule, select it in the table and click on the Edit button. • Click on the “Save” button for changes to be saved without activating the interface until you reboot the unit, the “Apply” button will save your settings and apply them immediately. To revert to the previous defaults, click on the “Revert” button. 3.4.
Network Tab Tunnel Name: Select the name of the GRE name by choosing one of the options available in the provided drop-down list. Enabled: Select Yes to enable the tunnel. Local bind-to IP: Set the local bind IP address for tunneled packets. This field is optional. Note: If supplied, the Local IP Address must be an address on another interface of this host. If not supplied, tunneled packets can be received from any interface. Local Endpoint IP/Mask (Required): Set the local GRE IP Endpoint IP/mask.
Network Tab 3.4.4.2 IP in IP Tunnels The IP in IP Tunnels menu items is used to configure a simple IP Tunnel. IP in IP Tunnel essentially encapsulates an IP packet into another packet with the same protocol as the transport protocol. • Click on the IP in IP Tunnels menu item and the following window will appear: To add an IP in IP Tunnel: • Click on the Add button and the following window will appear: Tunnel ID (Required): Enter a unique numerical identifier in this field.
Network Tab Local IP Address (Required): Set the fixed local address for tunneled packets. Note: If supplied, the Local IP Address must be an address on another interface of this host. If not supplied, tunneled packets can be received from any interface. Local Subnet (Required): Set the local, private IPP network/mask. Remote IP Address (Required): Set the IP Address of the remote endpoint for this tunnel. Remote Subnet (Required): Set the remote, private IP network/mask.
Network Tab Do Nothing: Perform no action Restart: IPSEC is restarted Stop: IPSEC is stopped With these combinations, the connection management may be fine-tuned so that the tunnel(s) may be able to restart faster, rather than having to rely on Dead Peer detection or other time out mechanisms alone. Coordinate with PPPoE: You may select specific actions to be performed either upon PPP connect, PPP disconnect or both.
Network Tab IPSEC Tunnels • Click on the Add button and the following General Settings dialog window will appear: Tunnel Name (Required): Enter some descriptive text in this field as an aid identifying it. The value must not contain spaces. Enable Tunnel: Specify whether this tunnel should connect to its remote peer now and after any reboot. Tunnel Type: Controls the initial mode of the tunnel at startup.
Network Tab Use Perfect Forward Secrecy: Specifies whether or not the tunnel will use Perfect Forward Secrecy when negotiation cryptography parameters with the remote device. Note: This parameter must be set the same on the devices on both sides of the tunnel in order for a Security Association (SA) to be established. This is one of the first things that should be checked when tunnel negotiation difficulties are encountered.
Network Tab • Click on the NEXT button and the following Termination Settings dialog window will appear: Local Public IP Address: This parameter typically only needs to be specified when the Red Lion router is configured to use more than one external, untrusted interface. Specify the IP Address of the left participant’s public network interface.
Network Tab • Click on the Finish button. You will be returned to the IPSEC dialog window and the IPSEC Tunnels table will now be populated with the recently entered data. • To delete an existing rule, select it in the table and click on the Delete button. To edit an existing rule, select it in the table and click on the Edit button.
Network Tab DNS lookup. Note: This setting may be overridden if a network interface is set to obtain its configuration information from its peer (either via PPP or DHCP). Enter Alternate DNS Server #2: This field is already filled in; it is showing the current server in use by the Red Lion server. Enter the IP Address of a Backup DNS Server you want to use, if the Primary DNS Server is unable to perform a DNS lookup.
Network Tab 3.4.6 Static Routes The Static Routes menu allows you to configure a route to a network through an interface manually. • Click on the Static Routes menu item and the following dialog window will appear: To add a Static Route on the Red Lion router: • Click on the Add button and the dialog window below will appear: Interface: Select the interface to which the route should be applied by selecting one of the available options from the drop-down list.
Network Tab through 192.168.1.254 (with 192.168.1.255 reserved for a broadcast). An address outside of that range is on a different network which would need to be accessed indirectly through a router and that router would be the gateway to the network on which the remote target device resides. In order to communicate with it, it would mean sending and receiving via the gateway device. The address must be one within the valid range for the network on which the designated interface resides.
Network Tab [SYN] Tx Timeout (Required): Specifies the timeout value, in seconds, for SYN packets for connection tracking. 65 is generally recommended default, which differs from the system default of 120. The recommended default for IP ATMs is 30-120. Enter Timeout (Required): Specifies the amount of time, in seconds, that a TCP connection can remain in an idle state before sending Keep-Alive Probes to verify that the remote end of the socket is still available.
Services Tab 3.5 Services Tab The Services Tab is where you can configure the various service offerings of the Red Lion router. These services include DHCP Server, DHCP Relay, Dynamic DNS, SN Proxy Settings, SixView Manager, GPS Settings, SSH/TELNET Server, SSL Connections, SNMP Agent, Ping Alive, Events and Serial IP. 3.5.1 DHCP Server Used to configure one of the internal Ethernet interfaces to be a DHCP server and hand out IP Addresses to systems connected to the Red Lion router.
Services Tab eth0: Enable DHCP: Specify whether you want to enable a DHCP Server for the interface. Note: If the interface is not enabled, or has been set to obtain its addressing parameters via DHCP, this option will be forced to “No”, and disabled until the interface is both enabled and set to use a static IP address. Enable Default Gateway: Provide Default Gateway IP Address to DHCP Client.
Services Tab • Click on the Add button to assign an IP Address to a device based on a MAC address, so that device obtains the same IP each time it requests a new IP from the DHCP server. The following window will appear: Enter Client MAC Address (Required): This is the field where you enter the Client’s computer or device MAC (Media Access Control) address.
Services Tab 3.5.2 DHCP Relay This feature will enable a DHCP Relay service, which will connect a local interface with a remote DHCP Server. DHCP Relay should not be enabled for any interface(s) which have been configured to act as a DHCP server. • Click on DHCP Relay and the following dialog window will appear: Enable DHCP Relay: Select YES to enable the DHCP Relay, or NO to disable it. The service will start once the Apply button is clicked.
Services Tab Interface Table: • Click on the ADD button and the following dialog window will appear: Select Interface: Select the interface to receive its IP from the remote DHCP server from the drop down menu. • Click on the Finish button. You will be returned to the DHCP Relay dialog window and the Interface Table will be populated with the entered data. • To delete an existing rule, select it in the table and click on the Delete button.
Services Tab Remote Server: Enter the IP Address or fully qualified domain name of all remote DHCP Servers available. It is the responsibility of the remote DHCP Server to coordinate the issuing DHCP addresses. • Click on the Finish button. You will be returned to the DHCP Relay dialog window and the Remote Servers table will be populated with the entered data. • To delete an existing rule, select it in the table and click on the Delete button.
Services Tab • Click on the Dynamic DNS menu item and the following dialog window will appear: Enable Dynamic DNS: Select Yes to enable the Dynamic DNS Service. Select Service Type: Select the desired Dynamic DNS Service from the list provided. Enter User Name (Required): Enter the User Name used to access your Dynamic DNS Service in this field. Enter Password (Required): Enter the password used to access your Dynamic DNS Service in this field.
Services Tab 3.5.4 SN Proxy Settings SN Proxy is a web relay proxy service used to gain access to devices that are behind our Red Lion router providing additional security and access control to devices that may not offer such functionality. A proxy based service provides a more robust connection than just using a port forward rule, including the ability to add an additional user login for authentication, encryption via SSL as well as isolation via Access Control Lists.
Services Tab 3.5.5 SixView Manager The SixView Manager menu item allows you to configure various aspects of the SixView Manager Client to communicate with a SixView Manager hosted at Red Lion or at your location.
Services Tab production rollouts. This will enable Red Lion support staff to monitor the progress and better assist in diagnosing potential problems. Select Connection Mode: Select the desired Connection Mode from the drop-down menu. • Primary Only: The SixView Manager client only connects to the Primary Server. • Secondary Only: The SixView Manager client only connects to the Secondary Server. • Both: The SixView Manager client connects to the Primary and Secondary Servers.
Services Tab 3.5.6 • GPS Settings Click on the GPS Settings menu item and the following dialog window will appear: Lockdown Radius Multiple (Required): Enter the value of the Lockdown Radius Multiplier in this field. The recommended setting for this field is 2. When the Geofence engine begins to build a fence, it will create a Calculated Minimum Radius allowed using an accuracy figure based on the acquisition 200 GPS location points obtained over an initial settling interval of about 15-20 minutes.
Services Tab The Modified Minimum Radius will not be allowed to be less than the Minimum Accuracy, and will be increased to the Minimum Accuracy as needed. The Minimum Accuracy will also provide a lower limit for the Fixed Lockdown Radius. The allowable range is 0-2000. Fixed Lockdown Radius (Required): The value of the Fixed Lockdown Radius may be entered in this field. The recommended setting for this option is 0 (off).
Services Tab • Report Only: The device reports violation events to a SixView Manager server. • Block Network: All network traffic, except to a SixView Manager server, will be blocked. • Block All: In addition to the actions taken in Block Network, all access to the device including via physical ports (console, etc.) is blocked. • Custom: Configured special actions are applied. Configure Advanced GPS Parameters: Select Yes to configure advanced GPS parameters.
Services Tab 3.5.7 SSH/TELNET Server The SSH/TELNET Server menu allows you to configure whether the Red Lion router will communicate with the network via Secure Shell (SSH) and to enable or disable TELNET on the Red Lion router. • Click on the SSH/TELNET menu item and the following dialog window will appear: SSH Server Enable SSH Server: Select YES to enable the SSH server. Note: Enabling the SSH Server does not, by default, allow SSH data through the firewall.
Services Tab Login Grace Time (seconds): Specifies the amount of time, in seconds, after which the SSH server will disconnect, if the user has not successfully logged in. The recommended setting for this field is 30. Maximum Concurrent Connections: Specifies the maximum number of concurrent unauthenticated connections to the SHH server. Additional connections will be dropped until authentication succeeds, or the Login Grace Time expires for a connection. The recommended setting for this field is 10.
Services Tab Select Activity Log Level: This option controls the logging level for SSL Connection activity. The recommended setting for a production environment is: Summary. For a test environment: Full. Wait for Connection (sec.): Time (in seconds) allowed after sending SYN packets, to wait for SYN-ACK. The recommended setting for this field is 20 seconds. Idle Timeout (min): Time (in minutes) allowed for no traffic over an SSL connection, before closing down the link.
Services Tab SSL Client Table Properties: • Click on the Add button and the following dialog window will appear: Label (Required): Enter a unique name to describe this connection. TCP Listening IP: Enter the IP to listen on for incoming connections. If not using static IP addresses, it is recommended to use the Advanced Setup option “Bind Interface for accepting TCP Connections” instead. The recommended settings for this field are: • Leave Blank (0.0.0.0) to allow connections from any interface.
Services Tab 3.5.8.2 SSL Server The SSL Server menu item is used to configure the Red Lion router to issue SSL certificates to requesting SSL clients. • Click on the SSL Server menu item and the following dialog window will appear: Enable SSL: Select Yes to configure SSL client/server. Select No and click the Apply button to disable SSL. Select Activity Log Level: This controls the logging level for SSL Connection activity. The recommended setting for a production environment is Summary.
Services Tab Ciphers: This field is a list of openssl ciphers supported. Please consult support staff before attempting to change. Reference Google:”open ssl cipher list” for more information. The recommended settings for this field are: RC4-MD5:RC4SHA:SSLv3. Select Keep-Alive behavior: This option enables TCP Keep-alives on the underlying sockets. The following options are supported: Select Keep-Alive behavior: This option enables TCP Keep-alives on the underlying sockets.
Services Tab SSL Listening Port (Required): Enter the listening port for SSL connections. Please note that this port must be allowed in the Firewall access rules for any external/untrusted interface. It may be helpful to review the results of Status->Network->Socket Statuses->TCP Only to confirm that your choice of listening port is not already in use. (Ports under “Local Address” with a stat of “LISTEN” are in use.
Services Tab • Click on the “SNMP Agent” menu item and the following dialog window will appear: Enable SNMP Agent: Select YES to enable the SNMP Agent. Note: Enabling the SNMP Agent does not, by default, allow SNMP data through the firewall. If you have connection problems, please check your firewall settings. Community String for SNMP Agent Access (Required): Specify the community string to use for authentication between the SNMP Agent and Manager. Alpha-numeric strings are supported.
Services Tab Enable Ping Alive: Select YES to enable the Ping Alive Service. The recommended setting for this option is NO. Ping Alive will send the specified number of packets in Test Packets to Send, every interval defined in Test Interval. Should the ping fail to the first host, a second host may also be defined. Host Fail Type will control how many hosts must fail before a failure is declared and Failure Command Script will execute the failure action specified at that time.
Services Tab 3.5.11 Events Events are used to apply a series of logic checks to a register(s) that allows the user to program an action based on the content of a specific register. Properly configured events can identify when a tank level is too high or if the RSSI signal strength has deviated outside an expected range, then react by writing to a known output and/or status register. Multiple events can be used to create more advanced logic or to create multiple stages of severity for alarms.
Services Tab Configuration • Click on the Add button and the Event ID dialog window will appear: Event Name (Required): Enter a unique name to describe this event. The name must be alphanumeric characters and must not contain spaces or digits only. Enable Event: Specify whether this specific event should be enabled by selecting YES or NO. Data Source: Choose which data source to use for this event. IODB: Monitor a specific IODB register value to trigger the event.
Services Tab • Once the desired information has been selected, click on the NEXT button and the next dialog window will appear: Event Type: An event is TRUE when: Data Match: The value of the register is equal to the alarm value. Data Mismatch: The value of the register is not equal to the alarm value. Absolute High: The value of the register exceeds the alarm's value. Absolute Low: The value of the register falls below the alarm's value.
Services Tab Manual: Requires a user to login and clear the event. An event that is not cleared will continue to generate actions if it is level triggered. If the action is edge triggered, and this event is not cleared, then no new event action will result. Deactivation Delay (in sec) (Required): Enter the time, in seconds, for the deactivation delay. This is also used to prevent an event from oscillating between the on and off states when the process is near the alarm condition.
Services Tab Rising Only: Executes the action only on transition of the event becoming true (active). Falling Only: Executes the action only on transition of the event becoming false (inactive). Both: Executes the action on any transition between true and false. Level Triggering: Selecting Yes will allow the action to execute as often as specified in the periodic action while the event remains true. Choosing NO indicates level will not be considered when evaluating the Event condition.
Services Tab 3.5.12 Serial IP The Serial IP menu item is used to configure serial communication such as POS device, serial data logging or serial transmitter via serial cable on the Red Lion router and third party UDP or TCP/IP Client/Server application. • Select the Serial IP menu item and the following dialog window will appear: Enable Serial IP: Select Yes to enable the Serial IP interface. Configuration Description: Enter a description to describe the intent of this communication.
Services Tab Connect Mode: If this option is set to No, the device will expect to receive AT Commands in order to go to active state. Some DTE (Data Terminal Equipment) devices required to go active if they provide DTR (Data Terminal Ready) signal. The recommended setting for this field is Yes, if DTR is the connect signal.
Services Tab TCP Client: If this option is selected, the device will act as a TCP Client and connects to the host processor once the serial port becomes active. TCP/UDP Independent Activation: This option determines if the TCP/IP port of the device will accept data before the remote side (Serial Port) is active. At least one of the two sides in the configuration must be set for Independent Activation. If neither side is set, then the device will not accept data.
Services Tab indicator First, Mid and Last when dealing with the large TCP messages and possibility of TXP/IP packet fragmentation. Allow peer to re-attache while connected: Select whether or not to allow TCP peer to re-attache to our server while the socket is connected. If enabled, a new connection attempt from the same peer will be accepted, and the previous TCP connection will be closed. This can be useful to re-establish a connection if the link is not closed gracefully.
Services Tab remote peer’s IP). If set to a specific IP, then packets will be sent to this IP only. The recommended setting for this field is “0.0.0.0” to allow any IP to send packets to the peer import number. You also have the option to set a second, third, fourth and fifth address in respective fields further below on the dialog window. Peer IP Port (Required): Enter the peer Port number into the field. This is required for UDP communication.
Services Tab Enter Address 1 (Required): This field indicates the Client Primary IP Address that the GWLNX uses to connect to the Host Server. Enter Port 1 (Required): This field indicates the Client Primary Port Address that the GWLNX uses to connect to the Host Server Port. Connect Timeout 1 (Required): This field is used to specify the time (in seconds) to attempt a connection to this TCP Destination, before declaring it unreachable. After the specified time, the next destination will be attempted.
Automation Tab 3.6 Automation Tab The Automation menu contains all aspects of managing your Modbus and DNP3 based I/O. Note: If prompted for an Unlock Key, contact Red Lion Support at support@redlion.net or 1-877-432-9908 This option is only supported if the IndustrialPro router has been upgraded from an SN prefix to IndustrialPro RAM and for the RAM 9000 series. The IndustrialPro RAM firmware MODBUS application allows it to act as a MODBUS Master acting as an I/O concentrator for MODBUS/DNP3 devices.
Automation Tab The user interfaces will have the ability to: • Configure/Display local station information such as station name and station number. • Configure/Display serial ports • Configure/Display remote stations • Configure/Display I/O transfers • Configure/Display MODBUS forward stations • Configure/Display MODBUS registers allocation 3.6.1 • Local Station Click on the Local Station sub menu item and the following menu will appear: Enable Modbus: Select Yes to enable the Modbus option.
Automation Tab 3.6.2 Serial Ports This section is used to configure the RS-232 port that is facing the front of the Red Lion device to integrate into your Modbus/DNP3 schema. • Click on the “Serial Port” menu item and the following window will appear: • Click on the Add button and the following pop-up window will appear: Device Name: Name of the serial device. Valid values: ttys1 (RS232), ttys5 (RS485) Baud Rate: Baud rate for the serial device.
Automation Tab Parity: Parity for serial device. Supported parities are: none, even, odd, mark and space. Flow Control: Flow control for serial device. Supported flow controls are: none, hardware, xon/xoff, half duplex, full duplex. Stop Bits: Stop bits for serial device. Supported stop bits are 1 and 2. Protocol: Protocol being used on serial device. Supported protocols are: DNP3, Modbus Master ASCII, Modbus Master RTU, Modbus Slave ASCII, Modbus Slave RTU, Modbus Master RTU Fwd and Modbus ASCII Fwd.
Automation Tab • To add a new tag, click on the ADD button. A new blank line will appear at the bottom of the Tags list. Name: Enter a unique name for the tag. The tag name may contain upper and lower case alpha numerical characters. The only special characters allowed are the period (.) and the underscore (_). Type: Select the desired output type from the drop down list. Available choices are: AI, AO, DI, DO, LI, LO, FI, FO. Address: Enter the desired tag address.
Automation Tab 3.6.4 Modbus 3.6.4.1 Remote Station: • Click on the Remote Station menu item and the following dialog window will appear: • Click on the Add button to configure the remote station parameters and the following pop-up window will appear: Station Name (Required): Enter the name of the remote station. The remote station name must be less than or equal to 32 characters.
Automation Tab Station Number (Required): Enter the remote station number. The station number must be in range of 1-247. Remote IP Address (Required): Enter the remote station IP address in a valid IPv4 unicast address format, or it may be blank if I/O transfers to this remote station only use the serial port. Remote IP Port (Required): Enter a valid IP port number (1-65535) that the remote station listens on for MODBUS requests. Take care to choose a port number not already used by other system services.
Automation Tab 3.6.4.2 • I/O Transfer Click on the I/O Transfer menu item and the following window will appear: Register Allocation: This section is displaying the default values for the following: Analog In: By default we support 5000 Analog Input registers, but the range is 1 - 10000. Analog Out: By default we support 5000 Analog Output registers, but the range is 1 - 10000. Long In: By default we support 2000 Long Input registers, but the range is 1 - 10000.
Automation Tab The range of Modbus slave addresses are displayed based on default register allocation. You can change the registers allocation values to your required register values and the range of Modbus slave addresses will be changed based on the new values. • Click on the Add button to configure the I/O Transfer for the remote station and the following pop-up window will appear: Station Name: Name of the remote station for this I/O transfer.
Automation Tab Valid Values: Wait for Reply or Rapid Fire Port: The port that the I/O request is being sent across. The supported ports are: RS232 Port, UDP and TCP. If UDP or TCP port are selected, the remote station selected for this I/O transfer should have its IP address defined. Command Type: The commands used for I/O transfers are: READ: Used for reading MODBUS registers from the remote station. WRITE: Write MODBUS output registers to the remote stations.
Automation Tab Table 1 - I/O Types and Limits for read commands I/O Type Number of regs supported in I/O transfer Float Output FO 62 Long Input LI 62 Long Output LO 62 Table 2 - I/O Types and Limits for write commands I/O Type Number of regs supported in I/O transfer Discrete Input DI 1968 Discrete Output DO 1968 Analog Input AI 123 Analog Output AO 123 Float Input FI 61 Float Output FO 61 Long Input LI 61 Long Output LO 61 Table 3 - Valid Type Combinations for READ I
Automation Tab 3.6.4.3 Forwards • Click on the Forwarding menu item and the following dialog window will appear: • Click on the Add button to configure the Forwarding and the following pop-up window will appear: Station Number (Required): Station number to be forwarded. Valid values are 1 - 247. Forward Station Number: If supplied, replaces the station number in the request with this value. Valid values are 1 247. Communication Type: Select the forwarding method.
Automation Tab • Click on the Finish button to populate the Forwarding Table screen. If more than one forward is needed, click and repeat the Add button. • Click on the “Save” button to save the Forwarding configuration in the modbus.xml file. The “Apply” button will save your settings and apply them immediately. To revert to the previous defaults, click on the “Revert” button. 3.6.4.
Automation Tab 3.6.5 DNP3 DNP3 (Distributed Network Protocol) is a set of communications protocols used between components in process automation systems. Its main use is in utilities such as electric and water companies. Usage in other industries is not common. It was developed for communications between various types of data acquisition and control equipment. 3.6.5.1 • General Click on the DNP3>General menu option and the following screen will appear: Compatibility Mode: The DNP v3.
Automation Tab Enable Unsolicited Responses: Select if the DNP Slave should send unsolicited messages to the DNP Master. If this selection is checked, then the user should also configure the following: DNP Address to Send Unsolicited Messages to: The address of the station to which DNP Slave will send unsolicited messages in the DNP Address to Send Unsolicited Messages field.
Automation Tab 3.6.5.2 Physical Link Layer Select Mode of Operation: The DNP V3.00 Slave Driver implementation supports RS-232 and RS-485 (two and four wires) over serial port communications as well as TCP/IP and UDP/IP over LAN/WAN communications. When the user selects the Serial Mode, the TCP/UDP section is disabled. The same happens to the Serial section if the Mode of Operation selected is TCP or UDP. Serial: This section groups all the parameters needed to establish serial communication.
Automation Tab 3.6.5.3 Data Link and Application Layer Use Local Station Number as This Station DNP Address: DNP address for the slave. This value can be set by the user or automatically assigned by the Add-On. If the check box Same As station Number is selected, then the DNP Address will be equal to the Station Number. Enter Station DNP Address (Required): Enter the address for this Station if not being automatically assigned.
Automation Tab Application Layer Retries: The number of Retries is configurable between 0 (Application Link Retries disabled) and 255. Application Layer Timeouts (ms): The Retry Timeout is configurable between 0 (Application Link Retries disabled) and 5,000ms Use different SEQ numbers for CONFIRM and RESPONSE: Check to enable • 3.6.5.4 Click on the “Save” button to save your configuration. The “Apply” button will save your settings and apply them immediately.
Automation Tab Binary Inputs Map I/O: This section provides configuration of Mapping Binary Input I/O’s Reg/Index to DNP points for generating events based on configured Class Assignments when the status of any Binary Input I/O’s changes. Default Class Assignments are applied to all the Reg/Index defined by Highest Register Address except Reg/Index entries that are defined in Exception Class Assignments Table. Configure DNP Points: If option is No, then no Binary Inputs is mapped as DNP points.
Automation Tab • Click the Add button to define an Exclusion range. Starting Reg/Index (Required): Enter the Starting Register for exception class assignments. The valid ranges are 0 to your configured highest register, and must be less than or equal to Ending Register. Ending Register (Required): Enter the Ending Register for exception class assignments. The valid ranges are 0 to your configured highest register, and must be greater than or equal to Starting Register.
Automation Tab Analog Inputs Map I/O This section provides configuration of Mapping Analog Input I/O’s Reg/Index to DNP points for generating events based on configured DeadBand and Class Assignments when the status of any Analog Input I/O’s changes. Default DeadBand and Class Assignments are applied to all the Reg/Index defined by Highest Register Address except Reg/ Index entries that are defined in Exception DeadBand and Class Assignments Table.
Automation Tab associated to a class (Class 1, Class 2 or Class 3), otherwise it should be associated to None. By default all DNP Points don’t generate events, this feature should be modified by the user. Default Object 33 - Frozen Change Event: This field is activated on both Levels 2 and 2+. It’s used to determine if a DNP point will generate events.
Automation Tab Object 32 - Analog Change Event: This field is activated on both levels 2 and 2+. It’s used to determine if a DNP point will generate events. In case a DNP point generates events (Object 2 Binary Change Events) then it should be associated to a class (Class 1, Class 2 or Class 3), otherwise it should be associated to None. By default all DNP Points don’t generate events, this feature should be modified by the user.
Automation Tab Floating Inputs Map I/O: This option provides configuration of Mapping Float Input I/O’s Reg/Index to DNP points for generating events based on configured DeadBand and Class Assignments when the status of any Float Input I/O’s changes. Default DeadBand and Class Assignments are applied to all the Reg/Index defined by Highest Register Address except Reg/ Index entries that are defined in Exception DeadBand and Class Assignments Table.
Automation Tab associated to a class (Class 1, Class 2 or Class 3), otherwise it should be associated to None. By default all DNP Points don’t generate events, this feature should be modified by the user. Default Object 33 - Frozen Change Event: This field is activated on both Levels 2 and 2+. It’s used to determine if a DNP point will generate events.
Automation Tab Object 32 - Analog Change Event: This field is activate by both Levels 2 and 2+. It’s used to determine if a DNP point will generates events (Object2 Binary Change Events) then it should be associated to a class (Class 1, Class 2 or Class 3), otherwise it should be associated to None. By default all DNP Points don’t generate events, this feature should be modified by the user. Object 33 - Frozen Change Event: This field is activate by both Levels 2 and 2+.
Automation Tab Long Inputs Map I/O: This option provides configuration of Mapping Long Input I/O’s Reg/Index to DNP points for generating events based on configured DeadBand and Class Assignments when the status of any Long Input I/O’s changes. Default DeadBand and Class Assignments are applied to all the Reg/Index defined by Highest Register Address except Reg/ Index entries that are defined in Exception DeadBand and Class Assignments Table.
Automation Tab Default Object 32 - Analog Change Event: This field is activated on both Levels 2 and 2+. It’s used to determine if a DNP point will generate events. In case a DNP point generates events (Object 2 Binary Change Events) then it should be associated to a class (Class 1, Class 2 or Class 3), otherwise it should be associated to None. By default all DNP Points don’t generate events, this feature should be modified by the user.
Automation Tab Object 31 - Frozen Analog Input: This field is activated on both Levels 2 and 2+. It’s used to determine if a DNP point will generate events. In case a DNP point generates events (Object 2 Binary Change Events) then it should be associated to a class (Class 1, Class 2 or Class 3), otherwise it should be associated to None. By default all DNP Points don't’ generate events, this feature should be modified by the user.
Automation Tab Binary Counters Map I/O: This option provides configuration of Mapping Binary Counters I/O’s Reg/Index to DNP points for generating events based on configured DeadBand and Class Assignments when the status of any Binary Counter I/O’s changes. DeadBand and Class Assignments are applied to all the Reg/Index defined by Highest Register Address except Reg/Index entries that are defined in Exception DeadBand and Class Assignments Table.
Automation Tab Default Object 23 - Frozen Change Event: This field is activated on both Levels 2 and 2+. It’s used to determine if a DNP point will generate events. In case a DNP point generates events (Object 2 Binary Change Events) then it should be associated to a class (Class 1, Class 2 or Class 3), otherwise it should be associated to None. By default all DNP Points don’t generate events, this feature should be modified by the user.
Automation Tab associated to a Class (Class 1, Class 2 or Class 3), otherwise it should be associated to None. By default, all DNP Points don't generate events, this feature should be modified by the user. Object 23 - Frozen Change Event: This field is activated on both Levels 2 and 2+. It’s used to determine if a DNP point will generate events.
Automation Tab Analog Objects 30: Analog Input: Combo Box that shows the different choices for Object 30 (Analog Input) that the user can select as a default variation. 31: Frozen Analog Input: Combo Box that shows the different choices for Object 31 (Frozen Analog Input) that the user can select as a default variation (only on Level 2+). 32: Analog Change Event: Combo Box that shows the different choices for Object 32 (Analog Input Change Events) that the user can select as a default variation.
Automation Tab Import Configuration File: This option will allow you to import a configuration file to replace your existing DNP3 configuration file. Simply click on Select File button to select your DNP3 configuration file on your PC, click on the Import button to replace your existing DNP3 configuration file. Download Appropriate File to your PC: You may use this feature to download the DNP3 configuration file (sxdnpdrv.ini) or DNP3 debug file (dnp3debug.log) to your local drive for review analysis.
Automation Tab Digital Input Address: Enter the address of internal IODB database for Digital Input I/O control. Valid values for this field are 1 through 65535 as defined for specified I/O type. Digital Input Counter Address: Enter the address of internal IODB database for Digital Input Counter. The valid values for this field are 1 through a value of defined register allocation configured for Analog Input I/O type.
Automation Tab Idle Timeout: With this enabled (checked), the browser will stop scanning after two minutes of inactivity. Select Type: From the drop down list, select the type of I/O you would like to test. Valid I/O types are: Analog In Discrete In Long In Float In Analog Out Discrete Out Long Out Float Out Start Address: Once the I/O type has been selected, enter the Start Address. Register Count: Enter the Register Count. • Click on the Add button to test the I/O.
Automation Tab CPU Monitor Timeout (ms): This option is used to make the I/O fail safe if the main CPU stops working. The main CPU controls communication, IODB and code written in C. If the main CPU stops working, the I/O processor will detect that in the time defined in this field. Suggested timeouts are 1000ms to 10000ms. Timeouts faster then 100ms are not recommended. The maximum allowed timeout value is 0xFFFF(65535ms). Setting this value to 0 will disable the feature.
Automation Tab Counter: This option will be available when Input Mode supports counters. When the checkbox is checked, the counter mode is enabled. The Count Value Size, Counter Mode and CNT Starting Address become available and must be configured as well. The counter value is stored in the CNT IODB address. Count Value Size: This is a plain counter mode that is either 16 or 32-bits in size, which counts on positive edge or negative edge depending on the polarity bit.
Automation Tab Discrete Output • Click on the Discrete Output button and the following dialog window will appear: TPO period (ms): Time Proportioned Outputs (TPO) are outputs that turn on and off in proportion to an analog value. Typically, the output will turn on and off once during the specified TPO period (cycle time). Specify a cycle time for all enabled TPO outputs in the module. The range of the cycle time is 20ms to 10 minutes (600,000ms).
Automation Tab Analog Input • Click on the Analog Input button and the following dialog window will appear: Analog Input Filtering: The table below explains the filtering (integration) options on the analog inputs. The faster the integration time, the quicker the channels will be sampled. However, quicker samples will render less accurate readings. For most accurate readings, select the slower sample/filtering settings.
Automation Tab Current Range: With this option selected, the analog input will be configured to take current instrumentation input (0-40mA or 4-20mA). The Input Range must also be configured. Input Range: Select the range that will be connected to the input channel. 0-5 VDC and 0-10 VDC: This option will be available when the Voltage Range option is selected. In these modes, the value will be scaled from the selected range (0-5 VDC and 0-10 VDC) to 0-32767 (decimal).
Automation Tab • Click on the I/O Channels button and the dialog window below will appear. The I/O Channels dialog window will provide a list of all the channels with their associated IODB/Modbus Address.
Automation Tab Calibration • Click on the Calibration button and the following dialog window will appear: Channel: A channel is a physical IO point that can be either analog or digital. User Zero Correction: Manually adjust the user offset calibration for analog inputs/outputs. Every analog/input is calibrated at the factory according to the specified accuracy. The user calibration is supplied to account to adjust the reported values to account for wiring or instrumentation errors.
Automation Tab 3. Set your analog device for a near full scale (85 to 95% full scale) output. Compare the value currently being reported with the value on your meter. If they are not equal, adjust the span value by using the slide bar and arrows in the span display box. Click the Apply button and observe the effect of the new span factor. Repeat this step unit a satisfactory reading is obtained. 4. The channel is now calibrated.
Automation Tab Status • Click on the Status button and the dialog window below will provide you with your system’s I/O Control Status and I/O Control Config Status. View in Test I/O: • 3.6.7.2 Click on the Test I/O button to be directed to the Test I/O Access dialog window. See section 3.6.5.2 for more information on this feature. Test I/O Test I/O is used to verify the functionality of I/O states in gateways, RTUs and I/O modules.
Automation Tab The Test I/O interface has been kept simple to make managing the test I/O process easier and keep the screen less cluttered and easier to look at and quickly locate your test values. Scan Rate: This is the time in which the screen will automatically refresh values from the internal I/ODB. Idle Timeout: When this option is enabled, the browser will stop scanning after two minutes of inactivity. Select Type: From the drop down list, select the type of I/O you would like to test.
Advanced Tab 3.7 Advanced Tab The Advanced Tab is used to configure the Red Lion router, which included IP Fallback, IP Transparency, Out-of-Band Management, VRRP, Sub-Systems and Gwlnx. 3.7.1 IP Fallback IP Fallback is supported in Red Lion routers in the IndustrialPro and EnterprisePro series. The IP Fallback option is used to configure the Red Lion router to failover between two interfaces, ex. Primary route on DLS/Cable on eth0, and secondary on Cellular if the primary loses Internet connection.
Advanced Tab Enable IP Fallback: Select YES to enable the IP Fallback. Enable this option if you have two paths (interfaces) configured with WAN (internet) support. An example would be primary ethernet (eth0) and secondary wireless (ppp0). Note: When using an ethernet port setup as DHCP Client, choose: Use Remote Gateway as Default Route: NO in the ethernet port setup screen. Default route control will be managed by the IP Fallback instead.
Advanced Tab 3.7.2 IP Transparency IP Transparency is supported on Red Lion routers in the IndustrialPro and EnterprisePro series. The IP Transparency menu item is used to configure the transparent bridging capability of the Red Lion router. IP Transparency is a special use capability. IP Transparency will take all inbound traffic to the Red Lion router and pass it transparently through to the interface specified.
Advanced Tab • Auto Detect: Use the ‘best negotiated’ speed and duplex (default) • 10 Mbps/Half: Force the interface to 10 Mbps and half-duplex • 100 Mbps/Half: Force the interface to 100 Mbps and half-duplex • 100 Mbps/Full: Force the interface to 100 Mbps and full-duplex Note: An incorrect ‘forced’ setting will result in communication failure for this interface. Enable DHCP Server: Select Yes to allow the DHCP Server(s) to be enabled while IP Transparency is in effect.
Advanced Tab Enable Out-of-Band Port Redirect: Select Yes to allow any Out-of-Band ports to be redirected locally to this device. When enabled, the OOB Ports specified in the Advanced->Out-of-Band Mgt section will be automatically allowed. The recommended setting for this field is Yes, when also configuring Out-of-Band Mgt on this unit. Enable Port Redirecting: Select Yes to allow redirecting of ports to a device beyond this device (the one being configured).
Advanced Tab 3.7.3 Out-of-Band Management The Out-of-Band Management menu item is used to configure the capability of remotely administrating a third-party device connected via a serial cable on the Red Lion router. Note: Please refer to the third-party device user manual and/or technical support to determine what type of connection is required to connect with the Red Lion router from the RS232 serial port.
Advanced Tab Interface: Select the interface to used. Note: For Speed, Bits, Parity and Stop Bits, consult the configuration of the remote device being attached; this setting must be compatible. Speed: Select the desired interface speed to be used. Bits per Character: Select the word length (bits per character) to be used. Parity: Select the parity to be used. Consult the configuration of the remote device being attached, this setting must be compatible.
Advanced Tab 3.7.4 VRRP (Virtual Redundancy Protocol) VRRP is supported in Red Lion routers in the IndustrialPro and EnterprisePro series. To configure VRRp, select the option from the Advanced menu. The VRRP menu item allows you to configure the capability of providing redundancy capabilities to each other as well as other third party devices.
Advanced Tab Enabled: Specify whether you want to enable the VRRP service on this device. The service will be started after clicking the Apply, and on each subsequent boot. VRRP is designed to work with multiple systems. Enable only if you intend to setup other VRRP partners. Interface: Specify the interface the VRRP service should use for communication. Use Virtual MAC Address: Specify whether you want to allow the VRRP service to handle virtual MAC addresses.
Advanced Tab 3.7.5.1 Configure Sub-Systems The “Configure Sub-Systems” menu item allows you to edit the main configuration files of the Red Lion router. It is not recommended that you perform configuration activities using this facility unless instructed to do so by Red Lion Technical Support. • Click on the Configure Sub-System menu item and the following window will appear: Select Sub-System To Configure: Select a component sub-system from the list as directed by Technical Support.
Advanced Tab • Click on the Add button to add a named interface and the following pop-up window will appear: Enter (logical) Interface Name (Required): Enter the name of the interface to be used for the logical interface. For example: tun0, gre4, ppp100, etc. • Click on the Finish button to populate the Predefined Interface Names screen. • Click SAVE to store the settings for the next reboot. Selecting Revert, will reset all fields to the previously saved defaults. 3.7.
Advanced Tab Generic: Please use the recommended setting unless directed to change by Red Lion Technical Support. The recommended setting for this field is No. File Mode: Please use the recommended setting unless directed to change by Red Lion Technical Support. The recommended setting for this field is DTMF. Connect Table Properties: To create a table setting, click on the Add button and the following dialog window will appear: Label (Required): Enter the Lookup Key associated with this entry.
Advanced Tab A value of “default” will designate this entry as the option to use if no other entry matches. If no “default” label exists, the first entry in the list will be the default and match any incoming number received. For a Dial/Ring-Out Mode, this field should match the phone number entered in the Com Port Manager configuration for Gwlnx TCP Server port number, if using a dynamic TCP Listening Port.
Advanced Tab Transparent Mode: This will enable an ENQ packet to be sent to the serial device to initiate a transaction. Up to 5 ENQ’s will be sent while waiting. Visa Mode: Unused. The Visa engine will automatically issue ENQ’s as needed, according to the Gwlnx config file. No Rx Before Tx: Discarding data before transmitting in supported Message Mode. The recommended setting for this field is No.
Advanced Tab STX - Payload - ETX - LRC: Strip only the LRC block check. STX - Payload - ETX - LRC: Send the fully formatted Visa message. Header Type: The TCP connection to a host may required length headers. This will optionally be prepended to the data received from the serial side, for either transparent or Visa Mode. The recommended setting for this field is Default. Default: Use current Gwlnx configuration. None: Use no headers. JBM Standard: Use JBM Standard Headers.
Advanced Tab Install Gwlnx Configuration File: Select Gwlnx Configuration File: Click the ‘Select File’ button to select a Gwlnx configuration file to upload from your local system. It is recommended that you do not upload new files unless directed by Red Lion Technical Support. Manage Gwlnx Configuration File: Select Gwlnx Configuration File: Select a Gwlnx configuration file on the remote unit to install or to delete.
Advanced Tab • Click on the Add button to define IP Destination Settings. The following dialog window will appear: Enter Address 1 (Required): This is a Client Primary IP Address that Gwlnx uses to connect to the Host Server. Enter Port 1 (Required): This is a Client Primary Port Address that Gwlnx uses to connect to the Host Server Port. Connect Timeout 1 (Required): Specify the time in seconds to attempt a connection to this TCP Destination, before declaring it unreachable.
Advanced Tab ommended setting for this field is 10 seconds. A value less than 10 seconds is not recommended for a wireless environment. Enter Address 3: This is a Client Second Alternative IP Address that Gwlnx uses to connect to the Host Server. Enter Port 3: This is a Client Second Alternative Port Address that Gwlnx uses to connect to the Host Server Port. Connect Timeout 3: Specify the time in seconds to attempt a connection to this TCP Destination, before declaring it unreachable.
Advanced Tab Auto Update: Select Yes to enable automatic updating of the log file display, the update interval can be selected using the Select Update Interval provided immediately below this control. Manual updating is disabled while auto-update is in effect. The current filter and maximum lines to be displayed will be used. Be advised that when connected via a Cellular interface, the log file data collected will count towards your total data plan usage.
Advanced Tab • Click on the Gwlnx Status menu item and the following dialog window will appear: Select Gwlnx Process ID to Restart: Select the Gwlnx Process ID (PID) that you would like to restart. • 3.7.6.7 Click on the Restart Button. This will restart the unit.
Advanced Tab • Click on the Gwlnx Log menu item and the following dialog window will appear: Filter string (optional): Enter a filter string in the space provided, only lines containing the filter value(s) will be displayed via a ‘grep’ style filter mechanism. Note that the filter is case sensitive. Number of lines to display: Select the number of lines to be displayed from one of the choices in the drop-down list provided. Choices include: 50, 100, 250, 500, 1000 & 2000.
Advanced Tab 3.7.7 Classic View If you prefer the original user interface, you may revert back to it by selecting the Classic View option. The functionality is the same as in the Web User Interface documented in this manual.
Chapter 4 Red Lion Support Technical Support For Technical Support on all products, Red Lion provides live phone support to serve you better. Hours are 8:00am to 5:30pm EST, Monday through Friday. Toll-free: 1-877-432-9908 (US and Canada) Phone: 1-518-877-5173 e-mail: support@redlion.net Website: www.redlion.net Customer Service Contact the Customer Service Department for all your product requirements.
Chapter 5 Compliance Statements & User Information FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Chapter 6 Licensing & Warranty Software supplied with each Red Lion product remains the exclusive property of Red Lion. Red Lion grants with each unit a perpetual license to use this software with the express limitations that the software may not be copied or used in any other product for any purpose. It may not be reverse engineered, or used for any other purpose other than in and with the computer hardware sold by Red Lion.
Chapter 7 Appendices Appendix A: RED-LION-RAM.MIB Contents Refers to: 3.5.10 SNMP Agent: RED-LION-RAM.MIB Contents Please note that the RAM-6021 Wired Router will not return any values for Wireless specific fields. The following MIBs are cellular specific. It is to be noted that all of the following can be retrieved on the SN firmware version of Red Lion's routers, the A, M, and R Series routers are dependent on the cellular module/aircard installed/inserted into the router.
Preferred Roaming List, a list of information that resides in the memory of the module/aircard. It lists the radio frequencies the module/aircard can use in various geographic areas. The part of the list for each area is ordered by the bands the module/aircardshould try to use first. Therefore it's a kind of priority list for whichtowers the module/aircard should use.
vendor DISPLAYSTRING modelName DISPLAYSTRING fwVersion DISPLAYSTRING hwVersion DISPLAYSTRING carrier DISPLAYSTRING lowRssi INTEGER32 lowEcio INTEGER32 highRssi INTEGER32 highEcio INTEGER32 currentRssi INTEGER32 currentEcio INTEGER32 Manufacturer of the module/aircard. Cellular Module manufacturer. The vendor-provided model name of the modem/card/module (e.g. sierra598U). Firmware version of the module/aircard. Cellular Module Firmware version #. Hardware version of the module/aircard.
hdrRoaming DISPLAYSTRING roaming INTEGER32 currentState INTEGER32 speedPref DISPLAYSTRING None, Roaming - SIDS Guaranteed, Roaming - SIDS Not Guaranteed. EVDO Roaming state. Cellular Roaming indicator - EVDO. 0 or 1. 0 = currently not roaming, 1 = currently roaming. Cellular current roaming status. Connecting, Dormant, Connected, Disconnected, Error, CallIncoming. Current Modem State. Cellular state (e.g. connecting, dormant, connected, disconnected, error, callincoming).
simContextApn0 DISPLAYSTRING simContextApn1 DISPLAYSTRING simStatus DISPLAYSTRING serviceDomain DISPLAYSTRING availServiceType DISPLAYSTRING wCdmaL1State DISPLAYSTRING mmccState DISPLAYSTRING gmmPsState DISPLAYSTRING wCdmaChannel DISPLAYSTRING wCdmaBand DISPLAYSTRING systemMode DISPLAYSTRING powerOnTime DISPLAYSTRING lowSpeedCsq DISPLAYSTRING highSpeedCsq DISPLAYSTRING band DISPLAYSTRING imei DISPLAYSTRING simId DISPLAYSTRING carrPLMN rxLevelC0 rxLevelC1 locAreaCode lteBand
lteRSRQ lteTracAreaCode creg cellularUpTime trafficppp0 todayRxPpp0 todayTotalPpp0 yesterdayRxPpp0 yesterdayTxPpp0 yesterdayTotalPpp0 CurrMonthRxPpp0 CurrMonthTxPpp0 CurrMonthTotalPpp0 PreMonthRxPpp0 PreMonthTxPpp0 PreMonthTotalPpp0 todayRxPpp0Kib todayTxPpp0Kib todayTotalPpp0Kib yesterdayRxPpp0Kib yesterdayTxPpp0Kib yesterdayTotalPpp0Kib CurrMonthRxPpp0Kib CurrMonthTxPpp0Kib CurrMonthTotalPpp0Kib PreMonthRxPpp0Kib PreMonthTxPpp0Kib PreMonthTotalPpp0Kib trafficwwan0 todayRxWwan0 todayTxWwan0 todayTotalWwan0
CurrMonthRxWwan0Kib CurrMonthTxWwan0Kib CurrMonthTotalWwan0Kib PreMonthRxWwan0Kib PreMonthTxWwan0Kib PreMonthTotalWwan0Kib trafficeth0 todayRxEth0 todayTxEth0 todayTotalEth0 yesterdayRxEth0 yesterdayTxEth0 yesterdayTotalEth0 CurrMonthRxEth0 CurrMonthTxEth0 CurrMonthTotalEth0 PreMonthRxEth0 PreMonthTxEth0 PreMonthTotalEth0 todayRxEth0Kib todayTxEth0Kib todayTotalEth0Kib yesterdayRxEth0Kib yesterdayTxEth0Kib yesterdayTotalEth0Kib CurrMonthRxEth0Kib CurrMonthTxEth0Kib CurrMonthTotalEth0Kib PreMonthRxEth0Kib Pr
yesterdayRxEth1Kib yesterdayTxEth1Kib yesterdayTotalEth1Kib CurrMonthRxEth1Kib CurrMonthTxEth1Kib CurrMonthTotalEth1Kib PreMonthRxEth1Kib PreMonthTxEth1Kib PreMonthTotalEth1Kib Software Manual INTEGER32 INTEGER32 INTEGER32 INTEGER32 INTEGER32 INTEGER32 INTEGER32 INTEGER32 INTEGER32 Vnstat Yesterday Rx for ETH1 Interface in Kib Vnstat Yesterday Tx for ETH1 Interface in Kib Vnstat Yesterday Total Rx/Tx for ETH1 Interface in Kib Vnstat Current Month Rx for ETH1 Interface in Kib Vnstat Current Month Tx for E
Appendix B: IODB Status Module The IODB status module is a set of IODB registers that are reserved for system use to collect device based information and make that information available to be polled by any head end or SCADA server appliances via Modbus based I/O transfers. These registers are created as Anolog OUT registers as not to interfere with any on board I/O or other commonly used register types.
1068 AI_Calibration Reserved N/A A non-zero value indicates user calibration is in progress 1069 AO_Calibration Reserved N/A A non-zero value indicates user calibration is in progress . Traffic - VNStat entries are in KiB (Kilobytes) Index Name Description Frequency Notes 1071 ppp0-TodayRX-A UINT32 Sometimes All UINT32 values should be handled as Unsigned, 32-bit Integers, Little Endian, LSB First.
1101 wwan0-YesterdayRX-A 1102 wwan0-YesterdayRX-B 1103 wwan0-YesterdayTX-A 1104 wwan0-YesterdayTX-B 1105 wwan0-YesterdayTotal-A 1106 wwan0-YesterdayTotal-B 1107 wwan0-ThisMonthRX-A 1108 wwan0-ThisMonthRX-B 1109 wwan0-ThisMonthTX-A 1110 wwan0-ThisMonthTX-B 1111 wwan0-ThisMonthTotal-A 1112 wwan0-ThisMonthTotal-B 1113 wwan0-LastMonthRX-A 1114 wwan0-LastMonthRX-B 1115 wwan0-LastMonthTX-A 1116 wwan0-LastMonthTX-B 1117 wwan0-LastMonthTotal-A 1118 wwan0-LastMonthTotal-B 1201 GP
1218 GPS-Speed SOG, tenths of knots Quickly 50.1 = 501 1219 GPS-Course Heading, in tenths of deg Quickly 280.
1335 wwan0 Subnet-a First Octet Often 1336 wwan0 Subnet-b Second Octet Often 1337 wwan0 Subnet-c Third Octet Often 1338 wwan0 Subnet-d Fourth Octet Often 1339 wwan0 DHCP NA Often 0 = Static IP, 1 = DHCP Assigned IP 1340 wwan0 Link Link Status Often 0 = No Link, 1 = Link detected 1341 br0 IP-a First Octet Often 1342 br0 IP-b Second Octet Often 1343 br0 IP-c Third Octet Often 1344 br0 IP-d Fourth Octet Often 1345 br0 Subnet-a First Octet Often 1346 br0 Subnet-b
Cellular - All cellular points are from cardstats file Index Name Description Frequency Notes 1701 IMEI-a First 4 digits, UINT16 Often 1702 IMEI-b Next 4 digits Often 1703 IMEI-c Next 4 digits Often 1704 IMEI-d Last 4 digits Often 1705 ESN-a UINT 64 - LIttle Endian Often 3G-ESN should be found by viewing the number in Hex.
