Pro3 Series 3D Printer User Manual * Please review this entire manual before operating the printer. This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
The contents of this User Manual maybe updated overtime. For the latest version, scan the QR code or visit the link below.
Pro3 Series 3D Printer / User Manual CONTENTS 01
Pro3 Series 3D Printer / User Manual A. Safety Read the following information to ensure safe usage of the appliance. 1 General information 2 Intended use Any damage or loss resulting from failure to follow the directions or warnings provided in this manual will not be covered under the product warranty.To ensure the printer is used safely and efficiently carefully read through the entire manual. This manual is intended for the installer and the user of the printer.
Pro3 Series 3D Printer / User Manual A. Safety Connect and operate the printer according to the specifications on the rating plate. Connect the printer to a power supply with an alternating current only via a properly installed outlet with grounding. The protective conductor system of the domestic electrical installation must be properly installed. The installation must have a sufficiently large cross-section.
Pro3 Series 3D Printer / User Manual A. Safety Do not let children play with packaging material. CAUTION ‒ Risk of injury! The printer may vibrate when in use. Place the printer on a clean, even, solid surface. Incorrectly laid tubes and power cords may result in a tripping hazard. Lay tubes and power cords to avoid creating a tripping hazard. If the printer is moved by holding onto protruding components, such as the printer door, the parts may break off.
Pro3 Series 3D Printer / User Manual A. Safety WARNING ‒ Choking Hazard! This machine contains many small parts and pieces. Do not allow children to breathe in or swallow small parts. Keep small parts away from children. Do not let children play with small parts. CAUTION ‒ Risk of injury! The printer’s lid is not designed to support weight and will likely break if stood on. Do not stand or climb on the printer. The appliance may tip over if you sit on or lean against the open door.
Pro3 Series 3D Printer / User Manual A. 6 Safety Safe Maintenance Take note of the safety instructions when performing maintenance work on the printer. WARNING ‒ Risk of electric shock! Improper repairs are dangerous. Repairs to the printer should only be carried out by trained specialist staff. Only use the manufacturer's original spare parts and original accessories when repairing the printer.
Pro3 Series 3D Printer / User Manual B. FCC Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Pro3 Series 3D Printer / User Manual C. Technical Specifications Pro3 Printer Build Volume (W×D×H) Machine Size (W×D×H) Electrical Pro3 Plus Single Extruder Print Dual Extruder Print Single Extruder Print Dual Extruder Print 300×300×300 mm 255×300×300 mm 300×300×605 mm 255×300×605 mm 620×626×760 mm Power Supply Input Power Supply Output Print Technology FFF Dual-head with electronic lifting system 1.
Pro3 Series 3D Printer / User Manual D.
Pro3 Series 3D Printer / User Manual D. List of Parts A. Top Cover The upper cover of the printer. B. Extruder The part extruding filament to the hot end; brand-new unitized extruders, which are more convenient to disassemble; a dual extrusion structure is adopted to adapt to a variety of filaments. C. Fans Used to cool the heat down. D.
Pro3 Series 3D Printer / User Manual D. List of Parts L. Filament Box The place where the filament is discharged, which can accommodate 2 rolls of 1kg filaments at the same time. M. Electric Control System Stores the motion controller board. N. USB Interface 2 USB2.0 interfaces. O. Ethernet Port RJ45 port to connect the printer to a network. P. Input Power AC input and switching.
Pro3 Series 3D Printer / User Manual E. Safety Marks Hot Surface: The hot surface sign indicates the presence of devices with high temperatures. Always use extra care when working around heated components. Wait half an hour after switching off the printer before handling parts to prevent burned fingers. Hot parts! Burned fingers when handing the parts. Wait one-half hour after switching off before handing parts.
Pro3 Series 3D Printer / User Manual E. 1 Safety Marks Installation To facilitate operation and maintenance, please keep a proper distance of 50cm on the side of the printer, 80cm on the front, 20cm on the back, and 60cm on the top during installation. No flammable materials are allowed around the installation location. 2 Filament and Electrical Precautions It is strongly recommended to use Raise3D official filaments and/or default settings for better performance.
Pro3 Series 3D Printer / User Manual E. Safety Marks Electromagnetic Compatibility - EMC Simplified EU Declaration of Conformity Raise3D declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. Full text of the EU declaration of conformity is available at https://www.raise3d.com.
Pro3 Series 3D Printer / User Manual F. Hardware Installation 1 Remove 2 Remove (×24) Locate the four shipping zip ties, and remove them. It is recommended to unclip these as opposed to cutting them. They can be reused if you need to transport your machine in the future. 3 Peel off the yellow stickers and remove the 24 security spacers. These clips are designed to hold the extruder assembly in place during shipping and, should be saved for future transport.
Pro3 Series 3D Printer / User Manual F. Hardware Installation 5 When the touch screen displays the "Home" screen, the printer is ready. Once the unit is powered on, the printer will go through a start-up sequence. Your Raise3D printer will take approximately 60 seconds to boot up. When the touch screen displays the "Home" screen, the printer is ready. 6 Tap the "Utilities" tab, and press the Z Homing button. Press OK for the print bed to begin to "Home" to the origin position.
Pro3 Series 3D Printer / User Manual F. Hardware Installation After removing the starter box, keep following the start-up wizard to finish the network connection, printer settings and RaiseCloud settings. After the start-up wizard, the printer will carry out 5-steps Offset Calibration, and the whole process takes about 1 hour. Calibrating the offset value of the printer can increase the printing success rate.
Pro3 Series 3D Printer / User Manual F. Hardware Installation 10 Adjust the flatness of the build plate. Precise flatness helps to get a better bottom surface of the model, avoiding warping or the model detaching from the build surface. 11 Adjust the matching gap between the left and right nozzles to ensure that the model will not be staggered in dual-color printing. 12 It aims to verify whether the adjustments in the previous four wizards are appropriate.
Pro3 Series 3D Printer / User Manual F. Hardware Installation Raise3D Supplies and Accessories 3mm 2.5mm 2mm 1.5mm Power Cable Hex Wrenches (×5) Filament (×2) Filament Guide Tube (×2) USB Storage Nozzle Cleaning Kit Heat Resistant Gloves Filament Holder Tweezers Thumb Screws &Other Accessories (Spare) 19 Spatula (×2) 0.
Pro3 Series 3D Printer / User Manual G. ideaMaker Installation The slicing software, ideaMaker, is available on the USB storage device included with your printer. Additional downloads and versions are available online at: www.raise3d.com Download ideaMaker https://www.raise3d.com/download/ WINDOWS 1 Install ideaMaker, and click "Next".
Pro3 Series 3D Printer / User Manual G. 2 3 21 ideaMaker Installation Follow the instructions provided by the guide, and click "Install". After the installation is finished, click "Next" to go to the next step. Click "Finish" and ideaMaker is installed.
Pro3 Series 3D Printer / User Manual G. ideaMaker Installation MAC OS X Open the Disk Image for the ideaMaker installer. This is located in the USB storage device included with your printer. Alternatively, you can download the latest version from www.raise3d.com/pages/download#down-im. Next, drag the ideaMaker icon(left) into the Application folder on the right side.
Pro3 Series 3D Printer / User Manual H. 1 2 23 ideaMaker Initial Settings When launching ideaMaker for the first time, you will need to select your printer model from the drop-down list, then press "Next". Select the diameter of your filament. Press "Finish" to finalize the initial settings. NOTE: ALL Pro3 printers use 1.75 mm filaments.
Pro3 Series 3D Printer / User Manual I. Using ideaMaker 1 2 3 Click the "+" button to import "Giveaway Spinner" included in the USB storage device. Click the "Start" " " button to begin slicing the model. Confirm that the selected printer type and material are correct, then select the standard slicing template. Click "Edit" to select the type of Platform Addition and the type of Support.
Pro3 Series 3D Printer / User Manual I. Using ideaMaker 4 5 6 25 Select your type of Platform Addition and Support in the "Edit" window. Click "Save and Close" to return to the previous menu. Click "Slice" to generate your file. Save the sliced files (.gcode and .data) by exporting them on the USB storage device. NOTE: File names that do not conform to the Western Latin character set may not display properly. Confirm that the files are saved and eject the USB storage device.
Pro3 Series 3D Printer / User Manual J. Dual Extruder Printing - Loading 1 Locate the open end of the filament, and feed it through the guide tube. NOTE: The operation of the left extruder is the same as that of the right extruder. Here we take the left extruder as an example. 2 After loading both sides of extruders, press the "Utilities" tab on the bottom of the screen, and set the temperature of the left nozzle to match the requirements of the filament that you are using.
Pro3 Series 3D Printer / User Manual J. Dual Extruder Printing - Slicing 1 Choose one of the models and set its designated Extruder as Left Extruder from the left side "Model Info" window. " 2 27 Choose the other model and set Extruder as the Right Extruder using the "Model Info" window.
Pro3 Series 3D Printer / User Manual J. Dual Extruder Printing - Slicing 3 4 Click the "Start" or " " button to begin slicing the model. Confirm your printer type and materials for both extruders, then select the standard sliding template. Click "Edit" to select the type of Platform Addition and the type of Support.
Pro3 Series 3D Printer / User Manual J. Dual Extruder Printing - Slicing 5 6 7 29 Select your type of Platform and Support in the "Edit" window. Click "Save and Close" to return to the previous menu. Click "Slice" to generate your file. Save the sliced files (. gcode and .data) to your USB storage device. NOTE: File names that do not conform to the Western Latin character set may not display properly. Confirm that the files are saved and eject the USB storage device.
Pro3 Series 3D Printer / User Manual J. Dual Extruder Printing - Start First Printing 1 Insert the USB device that contains your sliced model files (.gcode or .data) into the USB slot on the side of the touchscreen. USB Storage 2 Open the "Print" tab, and choose "USB Storage" to open the file storage path. Select your dual extrusion file to check the printing parameters and settings. Press "Print" to start printing the test file.
Pro3 Series 3D Printer / User Manual K. Dual Color Printing - Slicing 1 2 31 To perform higher-level dual-color printing and carry out offset calibration at the same time, please do the following. Load your filament type for both the left and right extruders. Each nozzle has a different printing range. To check the printing range of each nozzle when aligning models, tick the "Show Extruder's Printing Range" box.
Pro3 Series 3D Printer / User Manual K. Dual Color Printing - Slicing 3 4 5 Multiple colors are available for different nozzles' printing range. The "Align Together" feature can align multiple models to their original relative position (as defined during modeling) with each other. It can be located in the "Position" pop-up menu. Select the "Start" button, select your printing template, then open the "Per-Model Extruder" tab to set the nozzle settings per extruder.
Pro3 Series 3D Printer / User Manual K. 33 Dual Color Printing - Slicing 6 You may also set the extruders though the "Model Info" menu from the main window. 7 Double click a printing template in the "Select Template" windows, and click the "Advanced" button to access the Advanced Settings.
Pro3 Series 3D Printer / User Manual K. 8 9 Dual Color Printing - Slicing You can specify a nozzle to print support structure under Support tab. ideaMaker is not able to detect when a floating model is being supported by the opposite extruder and will prompt the user to add supports. The user should select not to add support structure as it will not be needed.
Pro3 Series 3D Printer / User Manual K. 10 11 35 Dual Color Printing - Slicing You can select your extruder and platform structure choice in the "Platform Additions" tab. These structures include: Raft, Brim, Skirt. (Raft is not recommended to use for PVA and flexible filament.) NOTE: You can edit the extruder's retraction amount under the "Ooze" tab. We recommend maintaining the "Extruder Amount of Extruder-switch" between 2-4 for standard filament types, and from 6-10mm for Raise3D Premium PLA.
Pro3 Series 3D Printer / User Manual K. 12 Dual Color Printing - Slicing Dual-extrusion with Multiple Filament Types Printing with multiple material types may limit printing compatibility. The table below lists all the officially-supported dual-extrusion material combinations currently possible on the Pro3.
Pro3 Series 3D Printer / User Manual L.
Pro3 Series 3D Printer / User Manual L. User Interface · Moving step distance setting · Disable Motor button · X/Y/Z axes move/home · Load and unload function for the L&R extruders Utilities · Choose where to load the print job from · Check uploading list, recovery task list, printing statistics Print *Contents of this brochure could be changed without written notice.
Experiencing Difficulties/Contact Information If you run into any issues during this guided setup, please contact our expert technicians by opening a ticket online at support.raise3d.com.
US Office 43 Tesla, Irvine, CA 92618, USA Netherlands Office Stationsplein 45 Unit A4.
