Owner's manual
Table Of Contents
- 8-bit MCU with CAN controller and Flash
- 1. Description
- 2. Features
- 3. Block Diagram
- 4. Pin Configuration
- 5. SFR Mapping
- 6. Clock
- 7. Program/Code Memory
- 8. Data Memory
- 9. EEPROM data memory
- 10. In-System-Programming (ISP)
- 11. Serial I/O Port
- 12. Timers/Counters
- 13. Timer 2
- 14. WatchDog Timer
- 15. Atmel CAN Controller
- 15.1. Introduction
- 15.2. CAN Controller Description
- 15.3. CAN Controller Mailbox and Registers Organization
- 15.4. IT CAN management
- 15.5. Bit Timing and BaudRate
- 15.6. Fault Confinement
- 15.7. Acceptance filter
- 15.8. Data and Remote frame
- 15.9. Time Trigger Communication (TTC) and Message Stamping
- 15.10. CAN Autobaud and Listening mode
- 15.11. CAN SFR’s
- 15.12. Registers
- 16. Programmable Counter Array PCA
- 17. Analog-to-Digital Converter (ADC)
- 18. Interrupt System
- 19. Electrical Characteristics
- 20. Ordering Information
Rev.A - May 17, 2001 61
Preliminary
T89C51CC02
13.4. Registers
T2CON (S:C8h)
Timer 2 Control Register
Reset Value = 0000 0000b
Bit addressable
Figure 47. T2CON Register
7 6 5 4 3 2 1 0
TF2 EXF2 RCLK TCLK EXEN2 TR2 C/T2# CP/RL2#
Bit Number Bit Mnemonic Description
7 TF2
Timer 2 overflow Flag
TF2 is not set if RCLK=1 or TCLK = 1.
Must be cleared by software.
Set by hardware on timer 2 overflow.
6 EXF2
Timer 2 External Flag
Set when a capture or a reload is caused by a negative transition on T2EX pin if EXEN2=1.
Set to cause the CPU to vector to timer 2 interrupt routine when timer 2 interrupt is enabled.
Must be cleared by software.
5 RCLK
Receive Clock bit
Clear to use timer 1 overflow as receive clock for serial port in mode 1 or 3.
Set to use timer 2 overflow as receive clock for serial port in mode 1 or 3.
4 TCLK
Transmit Clock bit
Clear to use timer 1 overflow as transmit clock for serial port in mode 1 or 3.
Set to use timer 2 overflow as transmit clock for serial port in mode 1 or 3.
3 EXEN2
Timer 2 External Enable bit
Clear to ignore events on T2EX pin for timer 2 operation.
Set to cause a capture or reload when a negative transition on T2EX pin is detected, if timer 2 is not used to
clock the serial port.
2 TR2
Timer 2 Run control bit
Clear to turn off timer 2.
Set to turn on timer 2.
1 C/T2#
Timer/Counter 2 select bit
Clear for timer operation (input from internal clock system: F
OSC
).
Set for counter operation (input from T2 input pin).
0 CP/RL2#
Timer 2 Capture/Reload bit
If RCLK=1 or TCLK=1, CP/RL2# is ignored and timer is forced to auto-reload on timer 2 overflow.
Clear to auto-reload on timer 2 overflows or negative transitions on T2EX pin if EXEN2=1.
Set to capture on negative transitions on T2EX pin if EXEN2=1.