User Manual

RA01
Version: 1.0 Date: 10/8/2008
Tel: [phone] Fax: [phone] E-mail: [e-mail] http://www.hoperf.com
8
DC Characteristics
Symbol Parameter Conditions/Notes Min Typ Max Units
fLO Receiver frequency 433 MHz band, 10 kHz resolution
868 MHz band, 20 kHz resolution
915 MHz band, 20 kHz resolution
400.96
801.92
881.92
439.03
878.06
930.00
MHz
BW Baseband fitler bandwidth mode 1
mode 2
mode 3
mode 4
mode 5
75
125
180
235
305
85
140
200
260
340
95
155
220
295
375
kHz
BRNRZ OOK bit rate with internal digital filters, NRZ data 4.8 40 kbps
BRM OOK bit rate with internal digital filters,
manchester coded data
2.4 20 kbps
Pmin Receiver sensitivity BER 3* 10-3, BW = 85 kHz, PN9,
BR = 9.6 kbps, Average signal
power
-110 dBm
IIP3outh Input IP3 out of band interferers
f-f
LO > 5MHz
-18 dBm
CCR Co-channel rejection BER = 10-2 with continuous wave
interferer in the channel
-4 dB
BR100kHz Blocking ratio BER = 10-2 with continuous wave
interferer, BW = 85 kHz,
interferer offset 100 kHz
45 dB
BR1MHz Blocking ratio same as above,
interferer offset 1 MHz
50 dB
BR10MHz Blocking ratio same as above,
interferer offset 10 MHz
67 dB
Pmaxh Maximum input power LNA: high setting
min 99.99% OOK modulation
-15 dBm
Pmaxa Maximum input power LNA: automatic or low gain setting
min 99.9% OOK modulation
0 dBm
Rin RF input impedance real
part (differential) (Note 1)
250 Ohm
Cin RF input capacitance 460 fF
RSa RSSI accuracy +/-7 dB
RSr RSSI range With automatic 32 dB LNA gain
switch
90 dB
RSresp DRSSI response time Until the RSSI output goes high
after the input signal exceeds the
preprogrammed
limit, C
ARRSI = 5nF
500 μs
fref PLL reference frequency (Note 2) 9.5 10 10.5 MHz
fresLB PLL frequency resolution 434 MHz Band 10 kHz
fresHB PLL frequency resolution 868 MHz or 915 MHz Band 20 kHz
Tsettl PLL settling time Frequency error < 1 kHz
after 1 MHz step
30 μs
tst1, P PLL startup time Initial calibration after power-up with
running crystal oscillator
500 μs
Pspur Spurious emission -60 dBm
Cxl Crystal load capacitance,
see crystal selection guide
Programmable in 0.5 pF steps,
tolerance +/- 10%
8.5 16 pF
tPOR Internal POR pulse width
(Note 3)
After Vdd has reached 90% of final
value
50 100 ms
tsx Crystal oscillator startup
time
Crystal ESR < 30 Ω 5 ms
tPBt Wake-up timer clock period Calibrated every 30 seconds (Note
4)
0.995 1 1.005 ms
twake-up Programmable wake-up
time
1
8.4*10
6
ms
Cin, D Digital input capacitance 2 pF
tr, f Digital output rise/fall time 15 pF pure capacitive load 10 ns
tr, f ,ckout Clock output rise/fall time 10 pF pure capacitive load 15 ns
fckout, slow Slow clock frequency Tolerance +/- 1 kHz 32 kHz