Manual

MAX7446
4-Channel Video Filter for RGB and CVBS Video
2 _______________________________________________________________________________________
ABSOLUTE MAXIMUM RATINGS
ELECTRICAL CHARACTERISTICS
(V
CC
= +5V ±5%, C
L
= 0 to 20pF, R
L
= 75Ω to GND for DC-coupled load, R
L
= 75Ω to V
CC
/ 2 for AC-coupled load, C
IN_
= 0.1µF,
T
A
= T
MIN
to T
MAX
, unless otherwise noted. Typical values are at V
CC
= +5V, T
A
= +25°C.)
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
V
CC
to GND ...........................................................................+6V
All Other Pins to GND.................................-0.3V to (V
CC
+ 0.3V)
Maximum Current into Any Pin Except V
CC
and GND .....±50mA
Continuous Power Dissipation (T
A
= +70°C)
TSSOP-EP (derate 20.8mW/°C above +70°C)...........1667mW
Operating Temperature Range ...........................-40°C to +85°C
Storage Temperature Range .............................-65°C to +150°C
Junction Temperature......................................................+150°C
Lead Temperature (soldering, 10s) .................................+300°C
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
Channel A 0.9 1.2 1.5
Passband Response
f = 100kHz to 5MHz,
relative to 100kHz
Channels B, C, D -0.75 +0.15 +0.75
dB
Stopband Attenuation A
SB
f ≥ 27MHz 39 43 dB
Differential Gain dG 5-step modulated staircase 0.15 0.50 %
Differential Phase dθ 5-step modulated staircase 0.15 0.50 D eg r ees
Signal-to-Noise Ratio SNR
Peak signal (2V
P-P
) to RMS noise,
f = 100Hz to 50MHz
80 dB
Channel A 17 30
Group Delay Deviation
∆t
g
Deviation from 100kHz
to 4.1MHz
Channels B, C, D 11 20
ns
Line-Time Distortion H
DIST
18µs, 100 IRE bar 0.3 %
Field-Time Distortion V
DIST
130 lines, 18µs, 100 IRE bar 0.5 %
Clamp Settling Time t
CLAMP
To ±1% 100 Lines
Channel A 0.6 0.9 1.1
Output DC Clamp Level
Channels B, C, D 1.1 1.5 1.8
V
Low-Frequency Gain Accuracy A
V
f = 100kHz -3 +3 %
Low-Frequency Gain Matching A
V
(
M ATC H
)
Low-frequency channel-to-channel matching,
f = 100kHz
4%
Group Delay Matching
t
g(MATCH)
Low-frequency channel-to-channel matching,
f = 100kHz
2ns
Channel-to-Channel Crosstalk X
TALK
f = 100kHz to 3.58MHz 60 dB
Output Short-Circuit Current I
SC
OUT_ shorted to GND or V
CC
70 mA
Input Leakage Current I
IN
10 µA
Channel A 1.2
Input Dynamic Swing
Channels B, C, D 0.9
V
P-P
SUPPLY
Supply Voltage Range V
CC
4.75 5.25 V
Supply Current I
CC
No load 100 140 mA
Power-Supply Rejection Ratio PSRR V
IN
= 100mV
P-P
, f = 0 to 3.5MHz 40 dB