User guide

ManualsBrandsRainbow Electronics ManualsSensorsATmega162V

201

202

203

204

205

206

207

208

209

210

Table Of Contents

Features
Pin Configurations
- Disclaimer
Overview
- Block Diagram
- ATmega161 and ATmega162 Compatibility
  - ATmega161 Compatibility Mode
- Pin Descriptions
- About Code Examples
AVR CPU Core
- Introduction
- Architectural Overview
- ALU – Arithmetic Logic Unit
- Status Register
- General Purpose Register File
  - The X-register, Y-register, and Z-register
- Stack Pointer
- Instruction Execution Timing
- Reset and Interrupt Handling
  - Interrupt Response Time
AVR ATmega162 Memories
- In-System Reprogrammable Flash Program Memory
- SRAM Data Memory
  - Data Memory Access Times
- EEPROM Data Memory
- I/O Memory
- External Memory Interface
- XMEM Register Description
System Clock and Clock Options
- Clock Systems and their Distribution
- Clock Sources
- Default Clock Source
- Crystal Oscillator
- Low-frequency Crystal Oscillator
- Calibrated Internal RC Oscillator
  - Oscillator Calibration Register – OSCCAL
- External Clock
- Clock output buffer
- Timer/Counter Oscillator
- System Clock Prescaler
  - Clock Prescale Register – CLKPR
Power Management and Sleep Modes
- MCU Control Register – MCUCR
- MCU Control and Status Register – MCUCSR
- Extended MCU Control Register – EMCUCR
- Idle Mode
- Power-down Mode
- Power-save Mode
- Standby Mode
- Extended Standby Mode
- Minimizing Power Consumption
System Control and Reset
- Resetting the AVR
- Reset Sources
- Power-on Reset
- External Reset
- Brown-out Detection
- Watchdog Reset
- MCU Control and Status Register – MCUCSR
- Internal Voltage Reference
  - Voltage Reference Enable Signals and Start-up Time
- Watchdog Timer
  - Watchdog Timer Control Register – WDTCR
- Timed Sequences for Changing the Configuration of the Watchdog Timer
Interrupts
- Interrupt Vectors in ATmega162
  - Moving Interrupts Between Application and Boot Space
  - General Interrupt Control Register – GICR
I/O-Ports
- Introduction
- Ports as General Digital I/O
- Alternate Port Functions
- Register Description for I/O-Ports
External Interrupts
- MCU Control Register – MCUCR
- Extended MCU Control Register – EMCUCR
- General Interrupt Control Register – GICR
- General Interrupt Flag Register – GIFR
- Pin Change Mask Register 1 – PCMSK1
- Pin Change Mask Register 0 – PCMSK0
8-bit Timer/Counter0 with PWM
- Overview
  - Registers
  - Definitions
- Timer/Counter Clock Sources
- Counter Unit
- Output Compare Unit
- Compare Match Output Unit
  - Compare Output Mode and Waveform Generation
- Modes of Operation
- Timer/Counter Timing Diagrams
- 8-bit Timer/Counter Register Description
Timer/Counter0, Timer/Counter1, and Timer/Counter3 Prescalers
- Internal Clock Source
- Prescaler Reset
- External Clock Source
- Special Function IO Register – SFIOR
16-bit Timer/Counter (Timer/Counter1 and Timer/Counter3)
- Restriction in ATmega161 Compatibility Mode
- Overview
- Accessing 16-bit Registers
  - Reusing the Temporary High Byte Register
- Timer/Counter Clock Sources
- Counter Unit
- Input Capture Unit
- Output Compare Units
- Compare Match Output Unit
  - Compare Output Mode and Waveform Generation
- Modes of Operation
- Timer/Counter Timing Diagrams
- 16-bit Timer/Counter Register Description
8-bit Timer/Counter2 with PWM and Asynchronous operation
- Overview
  - Registers
  - Definitions
- Timer/Counter Clock Sources
- Counter Unit
- Output Compare Unit
- Compare Match Output Unit
  - Compare Output Mode and Waveform Generation
- Modes of Operation
- Timer/Counter Timing Diagrams
- 8-bit Timer/Counter Register Description
- Asynchronous operation of the Timer/Counter
- Timer/Counter Prescaler
  - Special Function IO Register – SFIOR
Serial Peripheral Interface – SPI
- SS Pin Functionality
- Data Modes
USART
- Dual USART
  - AVR USART vs. AVR UART – Compatibility
- Clock Generation
- Frame Formats
  - Parity Bit Calculation
- USART Initialization
- Data Transmission – The USART Transmitter
- Data Reception – The USART Receiver
- Asynchronous Data Reception
- Multi-processor Communication Mode
  - Using MPCM
- Accessing UBRRH/ UCSRC Registers
  - Write Access
  - Read Access
- USART Register Description
- Examples of Baud Rate Setting
Analog Comparator
- Analog Comparator Control and Status Register – ACSR
JTAG Interface and On-chip Debug System
- Features
- Overview
- Test Access Port – TAP
- TAP Controller
- Using the Boundary- scan Chain
- Using the On-chip Debug system
- On-chip debug specific JTAG instructions
- On-chip Debug Related Register in I/O Memory
  - On-chip Debug Register – OCDR
- Using the JTAG Programming Capabilities
- Bibliography
IEEE 1149.1 (JTAG) Boundary-scan
- Features
- System Overview
- Data Registers
- Boundary-scan Specific JTAG Instructions
- Boundary-scan Chain
- ATmega162 Boundary- scan Order
- Boundary-scan Description Language Files
Boot Loader Support – Read-While-Write Self-programming
- Features
- Application and Boot Loader Flash Sections
  - Application Section
  - BLS – Boot Loader Section
- Read-While-Write and No Read-While-Write Flash Sections
  - RWW – Read-While-Write Section
  - NRWW – No Read-While-Write Section
- Boot Loader Lock Bits
- Entering the Boot Loader Program
  - Store Program Memory Control Register – SPMCR
- Addressing the Flash During Self- programming
- Self-programming the Flash
Memory Programming
- Program And Data Memory Lock Bits
- Fuse Bits
  - Latching of Fuses
- Signature Bytes
- Calibration Byte
- Parallel Programming Parameters, Pin Mapping, and Commands
  - Signal Names
- Parallel Programming
- Serial Downloading
- SPI Serial Programming Pin Mapping
- Programming via the JTAG Interface
Electrical Characteristics
- Absolute Maximum Ratings*
- DC Characteristics
- External Clock Drive Waveforms
- External Clock Drive
- SPI Timing Characteristics
- External Data Memory Timing
ATmega162 Typical Characteristics
- Active Supply Current
- Idle Supply Current
- Power-down Supply Current
- Power-save Supply Current
- Standby Supply Current
- Pin Pull-up
- Pin Driver Strength
- Pin Thresholds and Hysteresis
- BOD Thresholds and Analog Comparator Offset
- Internal Oscillator Speed
- Current Consumption of Peripheral Units
- Current Consumption in Reset and Reset Pulsewidth
Register Summary
Instruction Set Summary
Ordering Information
Packaging Information
- 44A
- 40P6
- 44M1
Erratas
- ATmega162, all rev.
Datasheet Change Log for ATmega162
- Changes from Rev. 2513D-04/03 to Rev. 2513E-09/03
- Changes from Rev. 2513C-09/02 to Rev. 2513D-04/03
- Changes from Rev. 2513B-09/02 to Rev. 2513C-09/02
- Changes from Rev. 2513A-05/02 to Rev. 2513B-09/02
Table of Contents

205

ATmega162/V

2513E–AVR–09/03

on the Fuse settings for the clock options, the part will remain reset for a Reset Time-out

Period (refer to “Clock Sources” on page 34) after releasing the Reset Register. The

output from this data register is not latched, so the reset will take place immediately, as

shown in Figure 86.

Figure 86. Reset Register

Boundary-scan Chain The Boundary-scan Chain has the capability of driving and observing the logic levels on

the digital I/O pins, as well as the boundary between digital and analog logic for analog

circuitry having Off-chip connections.

See “Boundary-scan Chain” on page 207 for a complete description.

Boundary-scan Specific

JTAG Instructions

The Instruction Register is 4-bit wide, supporting up to 16 instructions. Listed below are

the JTAG instructions useful for Boundary-scan operation. Note that the optional HIGHZ

instruction is not implemented, but all outputs with tri-state capability can be set in high-

impedant state by using the AVR_RESET instruction, since the initial state for all port

pins is tri-state.

As a definition in this datasheet, the LSB is shifted in and out first for all Shift Registers.

The OPCODE for each instruction is shown behind the instruction name in hex format.

The text describes which Data Register is selected as path between TDI and TDO for

each instruction.

EXTEST; 0x0 Mandatory JTAG instruction for selecting the Boundary-scan Chain as Data Register for

testing circuitry external to the AVR package. For port-pins, Pull-up Disable, Output

Control, Output Data, and Input Data are all accessible in the scan chain. For analog cir-

cuits having Off-chip connections, the interface between the analog and the digital logic

is in the scan chain. The contents of the latched outputs of the Boundary-scan chain is

driven out as soon as the JTAG IR-Register is loaded with the EXTEST instruction.

The active states are:

• Capture-DR: Data on the external pins are sampled into the Boundary-scan Chain.

• Shift-DR: The Internal Scan Chain is shifted by the TCK input.

• Update-DR: Data from the scan chain is applied to output pins.

From

TDI

ClockDR · AVR_RESET

TDO

From Other Internal and

External Reset Sources

Internal Reset