User guide

ManualsBrandsRainbow Electronics ManualsSensorsATmega162V

161

162

163

164

165

166

167

168

169

170

Table Of Contents

Features
Pin Configurations
- Disclaimer
Overview
- Block Diagram
- ATmega161 and ATmega162 Compatibility
  - ATmega161 Compatibility Mode
- Pin Descriptions
- About Code Examples
AVR CPU Core
- Introduction
- Architectural Overview
- ALU – Arithmetic Logic Unit
- Status Register
- General Purpose Register File
  - The X-register, Y-register, and Z-register
- Stack Pointer
- Instruction Execution Timing
- Reset and Interrupt Handling
  - Interrupt Response Time
AVR ATmega162 Memories
- In-System Reprogrammable Flash Program Memory
- SRAM Data Memory
  - Data Memory Access Times
- EEPROM Data Memory
- I/O Memory
- External Memory Interface
- XMEM Register Description
System Clock and Clock Options
- Clock Systems and their Distribution
- Clock Sources
- Default Clock Source
- Crystal Oscillator
- Low-frequency Crystal Oscillator
- Calibrated Internal RC Oscillator
  - Oscillator Calibration Register – OSCCAL
- External Clock
- Clock output buffer
- Timer/Counter Oscillator
- System Clock Prescaler
  - Clock Prescale Register – CLKPR
Power Management and Sleep Modes
- MCU Control Register – MCUCR
- MCU Control and Status Register – MCUCSR
- Extended MCU Control Register – EMCUCR
- Idle Mode
- Power-down Mode
- Power-save Mode
- Standby Mode
- Extended Standby Mode
- Minimizing Power Consumption
System Control and Reset
- Resetting the AVR
- Reset Sources
- Power-on Reset
- External Reset
- Brown-out Detection
- Watchdog Reset
- MCU Control and Status Register – MCUCSR
- Internal Voltage Reference
  - Voltage Reference Enable Signals and Start-up Time
- Watchdog Timer
  - Watchdog Timer Control Register – WDTCR
- Timed Sequences for Changing the Configuration of the Watchdog Timer
Interrupts
- Interrupt Vectors in ATmega162
  - Moving Interrupts Between Application and Boot Space
  - General Interrupt Control Register – GICR
I/O-Ports
- Introduction
- Ports as General Digital I/O
- Alternate Port Functions
- Register Description for I/O-Ports
External Interrupts
- MCU Control Register – MCUCR
- Extended MCU Control Register – EMCUCR
- General Interrupt Control Register – GICR
- General Interrupt Flag Register – GIFR
- Pin Change Mask Register 1 – PCMSK1
- Pin Change Mask Register 0 – PCMSK0
8-bit Timer/Counter0 with PWM
- Overview
  - Registers
  - Definitions
- Timer/Counter Clock Sources
- Counter Unit
- Output Compare Unit
- Compare Match Output Unit
  - Compare Output Mode and Waveform Generation
- Modes of Operation
- Timer/Counter Timing Diagrams
- 8-bit Timer/Counter Register Description
Timer/Counter0, Timer/Counter1, and Timer/Counter3 Prescalers
- Internal Clock Source
- Prescaler Reset
- External Clock Source
- Special Function IO Register – SFIOR
16-bit Timer/Counter (Timer/Counter1 and Timer/Counter3)
- Restriction in ATmega161 Compatibility Mode
- Overview
- Accessing 16-bit Registers
  - Reusing the Temporary High Byte Register
- Timer/Counter Clock Sources
- Counter Unit
- Input Capture Unit
- Output Compare Units
- Compare Match Output Unit
  - Compare Output Mode and Waveform Generation
- Modes of Operation
- Timer/Counter Timing Diagrams
- 16-bit Timer/Counter Register Description
8-bit Timer/Counter2 with PWM and Asynchronous operation
- Overview
  - Registers
  - Definitions
- Timer/Counter Clock Sources
- Counter Unit
- Output Compare Unit
- Compare Match Output Unit
  - Compare Output Mode and Waveform Generation
- Modes of Operation
- Timer/Counter Timing Diagrams
- 8-bit Timer/Counter Register Description
- Asynchronous operation of the Timer/Counter
- Timer/Counter Prescaler
  - Special Function IO Register – SFIOR
Serial Peripheral Interface – SPI
- SS Pin Functionality
- Data Modes
USART
- Dual USART
  - AVR USART vs. AVR UART – Compatibility
- Clock Generation
- Frame Formats
  - Parity Bit Calculation
- USART Initialization
- Data Transmission – The USART Transmitter
- Data Reception – The USART Receiver
- Asynchronous Data Reception
- Multi-processor Communication Mode
  - Using MPCM
- Accessing UBRRH/ UCSRC Registers
  - Write Access
  - Read Access
- USART Register Description
- Examples of Baud Rate Setting
Analog Comparator
- Analog Comparator Control and Status Register – ACSR
JTAG Interface and On-chip Debug System
- Features
- Overview
- Test Access Port – TAP
- TAP Controller
- Using the Boundary- scan Chain
- Using the On-chip Debug system
- On-chip debug specific JTAG instructions
- On-chip Debug Related Register in I/O Memory
  - On-chip Debug Register – OCDR
- Using the JTAG Programming Capabilities
- Bibliography
IEEE 1149.1 (JTAG) Boundary-scan
- Features
- System Overview
- Data Registers
- Boundary-scan Specific JTAG Instructions
- Boundary-scan Chain
- ATmega162 Boundary- scan Order
- Boundary-scan Description Language Files
Boot Loader Support – Read-While-Write Self-programming
- Features
- Application and Boot Loader Flash Sections
  - Application Section
  - BLS – Boot Loader Section
- Read-While-Write and No Read-While-Write Flash Sections
  - RWW – Read-While-Write Section
  - NRWW – No Read-While-Write Section
- Boot Loader Lock Bits
- Entering the Boot Loader Program
  - Store Program Memory Control Register – SPMCR
- Addressing the Flash During Self- programming
- Self-programming the Flash
Memory Programming
- Program And Data Memory Lock Bits
- Fuse Bits
  - Latching of Fuses
- Signature Bytes
- Calibration Byte
- Parallel Programming Parameters, Pin Mapping, and Commands
  - Signal Names
- Parallel Programming
- Serial Downloading
- SPI Serial Programming Pin Mapping
- Programming via the JTAG Interface
Electrical Characteristics
- Absolute Maximum Ratings*
- DC Characteristics
- External Clock Drive Waveforms
- External Clock Drive
- SPI Timing Characteristics
- External Data Memory Timing
ATmega162 Typical Characteristics
- Active Supply Current
- Idle Supply Current
- Power-down Supply Current
- Power-save Supply Current
- Standby Supply Current
- Pin Pull-up
- Pin Driver Strength
- Pin Thresholds and Hysteresis
- BOD Thresholds and Analog Comparator Offset
- Internal Oscillator Speed
- Current Consumption of Peripheral Units
- Current Consumption in Reset and Reset Pulsewidth
Register Summary
Instruction Set Summary
Ordering Information
Packaging Information
- 44A
- 40P6
- 44M1
Erratas
- ATmega162, all rev.
Datasheet Change Log for ATmega162
- Changes from Rev. 2513D-04/03 to Rev. 2513E-09/03
- Changes from Rev. 2513C-09/02 to Rev. 2513D-04/03
- Changes from Rev. 2513B-09/02 to Rev. 2513C-09/02
- Changes from Rev. 2513A-05/02 to Rev. 2513B-09/02
Table of Contents

170

ATmega162/V

2513E–AVR–09/03

Frame Formats A serial frame is defined to be one character of data bits with synchronization bits (start

and stop bits), and optionally a parity bit for error checking. The USART accepts all 30

combinations of the following as valid frame formats:

• 1 start bit

• 5, 6, 7, 8, or 9 data bits

• no, even or odd parity bit

• 1 or 2 stop bits

A frame starts with the start bit followed by the least significant data bit. Then the next

data bits, up to a total of nine, are succeeding, ending with the most significant bit. If

enabled, the parity bit is inserted after the data bits, before the stop bits. When a com-

plete frame is transmitted, it can be directly followed by a new frame, or the

communication line can be set to an idle (high) state. Figure 78 illustrates the possible

combinations of the frame formats. Bits inside brackets are optional.

Figure 78. Frame Formats

St Start bit, always low.

(n) Data bits (0 to 8).

P Parity bit. Can be odd or even.

Sp Stop bit, always high.

IDLE No transfers on the communication line (RxD or TxD). An IDLE line must be

high.

The frame format used by the USART is set by the UCSZ2:0, UPM1:0 and USBS bits in

UCSRB and UCSRC. The Receiver and Transmitter use the same setting. Note that

changing the setting of any of these bits will corrupt all ongoing communication for both

the Receiver and Transmitter.

The USART Character SiZe (UCSZ2:0) bits select the number of data bits in the frame.

The USART Parity mode (UPM1:0) bits enable and set the type of parity bit. The selec-

tion between one or two stop bits is done by the USART Stop Bit Select (USBS) bit. The

receiver ignores the second stop bit. An FE (Frame Error) will therefore only be detected

in the cases where the first stop bit is zero.

Parity Bit Calculation The parity bit is calculated by doing an exclusive-or of all the data bits. If odd parity is

used, the result of the exclusive or is inverted. The relation between the parity bit and

data bits is as follows::

even

Parity bit using even parity

odd

Parity bit using odd parity

Data bit n of the character

10 2 3 4 [5] [6] [7] [8] [P]St Sp1 [Sp2] (St / IDLE)(IDLE)

FRAME

even

n 1–

… d

odd

⊕⊕⊕⊕⊕⊕

n 1–

… d

1⊕⊕⊕⊕⊕⊕