User guide

ManualsBrandsRainbow Electronics ManualsSensorsATmega162V

151

152

153

154

155

156

157

158

159

160

Table Of Contents

Features
Pin Configurations
- Disclaimer
Overview
- Block Diagram
- ATmega161 and ATmega162 Compatibility
  - ATmega161 Compatibility Mode
- Pin Descriptions
- About Code Examples
AVR CPU Core
- Introduction
- Architectural Overview
- ALU – Arithmetic Logic Unit
- Status Register
- General Purpose Register File
  - The X-register, Y-register, and Z-register
- Stack Pointer
- Instruction Execution Timing
- Reset and Interrupt Handling
  - Interrupt Response Time
AVR ATmega162 Memories
- In-System Reprogrammable Flash Program Memory
- SRAM Data Memory
  - Data Memory Access Times
- EEPROM Data Memory
- I/O Memory
- External Memory Interface
- XMEM Register Description
System Clock and Clock Options
- Clock Systems and their Distribution
- Clock Sources
- Default Clock Source
- Crystal Oscillator
- Low-frequency Crystal Oscillator
- Calibrated Internal RC Oscillator
  - Oscillator Calibration Register – OSCCAL
- External Clock
- Clock output buffer
- Timer/Counter Oscillator
- System Clock Prescaler
  - Clock Prescale Register – CLKPR
Power Management and Sleep Modes
- MCU Control Register – MCUCR
- MCU Control and Status Register – MCUCSR
- Extended MCU Control Register – EMCUCR
- Idle Mode
- Power-down Mode
- Power-save Mode
- Standby Mode
- Extended Standby Mode
- Minimizing Power Consumption
System Control and Reset
- Resetting the AVR
- Reset Sources
- Power-on Reset
- External Reset
- Brown-out Detection
- Watchdog Reset
- MCU Control and Status Register – MCUCSR
- Internal Voltage Reference
  - Voltage Reference Enable Signals and Start-up Time
- Watchdog Timer
  - Watchdog Timer Control Register – WDTCR
- Timed Sequences for Changing the Configuration of the Watchdog Timer
Interrupts
- Interrupt Vectors in ATmega162
  - Moving Interrupts Between Application and Boot Space
  - General Interrupt Control Register – GICR
I/O-Ports
- Introduction
- Ports as General Digital I/O
- Alternate Port Functions
- Register Description for I/O-Ports
External Interrupts
- MCU Control Register – MCUCR
- Extended MCU Control Register – EMCUCR
- General Interrupt Control Register – GICR
- General Interrupt Flag Register – GIFR
- Pin Change Mask Register 1 – PCMSK1
- Pin Change Mask Register 0 – PCMSK0
8-bit Timer/Counter0 with PWM
- Overview
  - Registers
  - Definitions
- Timer/Counter Clock Sources
- Counter Unit
- Output Compare Unit
- Compare Match Output Unit
  - Compare Output Mode and Waveform Generation
- Modes of Operation
- Timer/Counter Timing Diagrams
- 8-bit Timer/Counter Register Description
Timer/Counter0, Timer/Counter1, and Timer/Counter3 Prescalers
- Internal Clock Source
- Prescaler Reset
- External Clock Source
- Special Function IO Register – SFIOR
16-bit Timer/Counter (Timer/Counter1 and Timer/Counter3)
- Restriction in ATmega161 Compatibility Mode
- Overview
- Accessing 16-bit Registers
  - Reusing the Temporary High Byte Register
- Timer/Counter Clock Sources
- Counter Unit
- Input Capture Unit
- Output Compare Units
- Compare Match Output Unit
  - Compare Output Mode and Waveform Generation
- Modes of Operation
- Timer/Counter Timing Diagrams
- 16-bit Timer/Counter Register Description
8-bit Timer/Counter2 with PWM and Asynchronous operation
- Overview
  - Registers
  - Definitions
- Timer/Counter Clock Sources
- Counter Unit
- Output Compare Unit
- Compare Match Output Unit
  - Compare Output Mode and Waveform Generation
- Modes of Operation
- Timer/Counter Timing Diagrams
- 8-bit Timer/Counter Register Description
- Asynchronous operation of the Timer/Counter
- Timer/Counter Prescaler
  - Special Function IO Register – SFIOR
Serial Peripheral Interface – SPI
- SS Pin Functionality
- Data Modes
USART
- Dual USART
  - AVR USART vs. AVR UART – Compatibility
- Clock Generation
- Frame Formats
  - Parity Bit Calculation
- USART Initialization
- Data Transmission – The USART Transmitter
- Data Reception – The USART Receiver
- Asynchronous Data Reception
- Multi-processor Communication Mode
  - Using MPCM
- Accessing UBRRH/ UCSRC Registers
  - Write Access
  - Read Access
- USART Register Description
- Examples of Baud Rate Setting
Analog Comparator
- Analog Comparator Control and Status Register – ACSR
JTAG Interface and On-chip Debug System
- Features
- Overview
- Test Access Port – TAP
- TAP Controller
- Using the Boundary- scan Chain
- Using the On-chip Debug system
- On-chip debug specific JTAG instructions
- On-chip Debug Related Register in I/O Memory
  - On-chip Debug Register – OCDR
- Using the JTAG Programming Capabilities
- Bibliography
IEEE 1149.1 (JTAG) Boundary-scan
- Features
- System Overview
- Data Registers
- Boundary-scan Specific JTAG Instructions
- Boundary-scan Chain
- ATmega162 Boundary- scan Order
- Boundary-scan Description Language Files
Boot Loader Support – Read-While-Write Self-programming
- Features
- Application and Boot Loader Flash Sections
  - Application Section
  - BLS – Boot Loader Section
- Read-While-Write and No Read-While-Write Flash Sections
  - RWW – Read-While-Write Section
  - NRWW – No Read-While-Write Section
- Boot Loader Lock Bits
- Entering the Boot Loader Program
  - Store Program Memory Control Register – SPMCR
- Addressing the Flash During Self- programming
- Self-programming the Flash
Memory Programming
- Program And Data Memory Lock Bits
- Fuse Bits
  - Latching of Fuses
- Signature Bytes
- Calibration Byte
- Parallel Programming Parameters, Pin Mapping, and Commands
  - Signal Names
- Parallel Programming
- Serial Downloading
- SPI Serial Programming Pin Mapping
- Programming via the JTAG Interface
Electrical Characteristics
- Absolute Maximum Ratings*
- DC Characteristics
- External Clock Drive Waveforms
- External Clock Drive
- SPI Timing Characteristics
- External Data Memory Timing
ATmega162 Typical Characteristics
- Active Supply Current
- Idle Supply Current
- Power-down Supply Current
- Power-save Supply Current
- Standby Supply Current
- Pin Pull-up
- Pin Driver Strength
- Pin Thresholds and Hysteresis
- BOD Thresholds and Analog Comparator Offset
- Internal Oscillator Speed
- Current Consumption of Peripheral Units
- Current Consumption in Reset and Reset Pulsewidth
Register Summary
Instruction Set Summary
Ordering Information
Packaging Information
- 44A
- 40P6
- 44M1
Erratas
- ATmega162, all rev.
Datasheet Change Log for ATmega162
- Changes from Rev. 2513D-04/03 to Rev. 2513E-09/03
- Changes from Rev. 2513C-09/02 to Rev. 2513D-04/03
- Changes from Rev. 2513B-09/02 to Rev. 2513C-09/02
- Changes from Rev. 2513A-05/02 to Rev. 2513B-09/02
Table of Contents

157

ATmega162/V

2513E–AVR–09/03

Serial Peripheral

Interface – SPI

The Serial Peripheral Interface (SPI) allows high-speed synchronous data transfer

between the ATmega162 and peripheral devices or between several AVR devices. The

ATmega162 SPI includes the following features:

•

Full-duplex, Three-wire Synchronous Data Transfer

• Master or Slave Operation

• LSB First or MSB First Data Transfer

• Seven Programmable Bit Rates

• End of Transmission Interrupt Flag

• Write Collision Flag Protection

• Wake-up from Idle Mode

• Double Speed (CK/2) Master SPI Mode

Figure 71. SPI Block Diagram

(1)

Note: 1. Refer to Figure 1 on page 2, and Table 32 on page 71 for SPI pin placement.

The interconnection between Master and Slave CPUs with SPI is shown in Figure 72.

The system consists of two Shift Registers, and a Master clock generator. The SPI Mas-

ter initiates the communication cycle when pulling low the Slave Select SS

pin of the

desired Slave. Master and Slave prepare the data to be sent in their respective Shift

Registers, and the Master generates the required clock pulses on the SCK line to inter-

change data. Data is always shifted from Master to Slave on the Master Out – Slave In,

MOSI, line, and from Slave to Master on the Master In – Slave Out, MISO, line. After

each data packet, the Master will synchronize the Slave by pulling high the Slave Select,

, line.

SPI2X

DIVIDER

/2/4/8/16/32/64/128