Specification

5000 Plus Series Full and Reversing
Full/Part Circle Sprinkler
The full and/or part circle sprinkler shall be a
single-stream, water-lubricated, gear-drive type
capable of covering a ___ foot (xx meter) at
___ pounds per square inch (psi) or (bar) with a
discharge rate of ___gallons per minute (___ gpm)
(___ m
3
/h). The sprinkler shall have a ow shut-o
device that is integrated into the ow path of the
rotor as well as adjustable arc coverage of 40 to
360 degrees. Arc adjustment can be performed
with or without the sprinkler in operation and shall
require only a at-blade screwdriver.
The sprinkler shall have a smoothed ow path
entrance to enhance the ow characteristics of the
rotor. In addition, the sprinkler shall feature a ow
path to nozzle bore transition radius to minimize
pressure loss and assure peak nozzle radius is
achieved.
The sprinkler shall have a pressure activated, multi-
function wiper seal that positively seals against the
pop-up stem to keep debris out of the rotor and to
clean debris from the pop-up stem as it retracts.
This wiper seal shall prevent sprinkler from sticking
up, and be capable of sealing the sprinkler cap to
sprinkler body under normal operating pressures.
The sprinkler shall have a screen installed in the
pop-up stem to lter inlet water, protect the drive
from clogging and simplify its removal for cleaning
and ushing of the system. It shall have a 3⁄4”
(FNPT) bottom inlet.
The sprinkler shall have a standard green rubber
cover and a strong stainless steel retract spring for
positive pop down. Pop-up height as measured
from the top of the cap, at normal installation, to
the middle of the nozzle orice shall be __ inches
or __ cm.
The rotor’s overall height shall be ___ inches
(_____cm), with an exposed surface diameter of
15⁄8” (4.1 cm).
The sprinkler shall have 12 interchangeable
nozzles: 8 Rain Curtain nozzles for superior
coverage and, 4 Low Angle nozzles for reduced
radius of throw and superior wind resistance with
all nozzles containing Micro-Ramp™ for superior
close-in watering. The angle of trajectory shall
be 25 degrees for the Rain Curtain nozzles and 10
degrees for the low angle nozzles. The sprinkler
shall come with a stainless steel adjusting screw
capable of reducing the radius up to 25%.
The sprinkler shall be as manufactured by Rain Bird
Corporation, Glendora, California.
Optional Feature Specication
5000 Plus Series SAM, Full and
Reversing Full/Part Circle
Sprinkler SAM unit
When so indicated on the design, the sprinkler
shall have a spring-loaded Seal-A-Matic™ (SAM)
device in the base of the case. The device shall
hold back at least 7’ (2, 13m) of elevation change to
prevent puddling, run-o and erosion caused by
low-head drainage.
5000 Plus Series Full and Reversing
Full/Part Circle Non-Potable
When so indicated on the design, the sprinkler
shall have a purple rubber cover to indicate to the
user that non-potable water is being used. There
shall be no dierence between the black and the
purple covers, except for the color.
The sprinkler shall be as manufactured by Rain Bird
Corporation, Glendora, California.
5000 Series Shrub Model
Full and Reversing Full/Part
Circle Sprinkler (SAM)
When so indicated on the design, the shrub
model shall contain all of the specications of the
standard 5000 series rotor plus a locking screw
to fasten the shrub unit to the riser. Additionally,
the shrub base unit will feature Secure Ribs™ that
are designed to assist in the staking of the shrub
model if so specied on the design. When the Seal-
A-Matic™ (SAM) model is indicated on the design,
the device shall hold back at least 7’ (2.13m) of
elevation change to prevent puddling, run-o and
erosion caused by low head drainage. As well the
SAM unit shall experience no pressure loss during
normal operation.
5000 Plus Series Stainless Steel
When so indicated on the design, the rotor shall
have a stainless steel covered nozzle turret and
riser stem. This riser stem shall be tapered and
conform to the standard plastic riser in all other
ways.
5000 MPR Nozzle Specication
The MPR Nozzle shall be capable of covering
a _____foot radius (FT.RAD.)/(meter) at
____pounds per square inch (psi)/(Bars) with
a discharge rate of _____gallons per minute
(GPM)/(m
3
/h, l/s).
The MPR Nozzle shall have a matched
precipitation rate of 0.6 in/hr (15 mm/h) at 45
psi (3.1 bar).
The MPR Nozzle shall be color-coded by radius.
The MPR Nozzle shall contain Micro Ramp™
technology for superior close-in watering.
The MPR Nozzle shall be manufactured by Rain
Bird Corporation, Azusa, California.
5000 Plus Series Rotor
Technical Specication
D39447EEO
Rain Bird Corporation
6991 E. Southpoint Road
Tucson, AZ 85756
Phone: [phone]
Fax: [phone]
Rain Bird Technical Services
(800) RAINBIRD (1-800-724-6247)
(U.S. and Canada)
Rain Bird Corporation
970 West Sierra Madre Avenue
Azusa, CA 91702
Phone: [phone]
Fax: [phone]
Specification Hotline
800-458-3005 (U.S. and Canada)
Rain Bird International, Inc.
1000 West Sierra Madre Ave.
Azusa, CA 91702
Phone: [phone]
Fax: [phone]
The Intelligent Use of Water
™
www.rainbird.com
® Registered Trademark of Rain Bird Corporation
© 2016 Rain Bird Corporation 6/16
How To Specify
5000 - MPR - 25 - Q
Model
5000 Series
Nozzle
Matched
Precipitation
Rate
Radius
Range
25’
30’
35’
Pattern
Q=Quarter
T=Third
H=Half
F=Full