Specification
Spray Nozzles
30
The Intelligent Use of Water.
™
5° Trajectory
Q V
Nozzle Pressure Radius Flow Precip Precip
psi ft. gpm In/h In/h
330° Arc 15 6 1.21 3.53 4.07
20 7 1.36 2.91 3.36
25 7 1.55 3.32 3.83
30 8 1.70 2.79 3.22
270° Arc 15 6 1.11 3.95 4.55
20 7 1.24 3.24 3.74
25 7 1.41 3.69 4.25
30 8 1.55 3.10 3.58
180° Arc 15 6 0.84 4.49 5.18
20 7 0.97 3.81 4.40
25 7 1.09 4.28 4.94
30 8 1.19 3.58 4.13
90° Arc 15 6 0.51 5.46 6.29
20 7 0.59 4.64 5.35
25 7 0.66 5.19 5.98
30 8 0.72 4.33 5.00
8 Series VAN
5° Trajectory
Q V
Nozzle Pressure Radius Flow Flow Precip Precip
bar m m3⁄h l/m mm/h mm/h
330° Arc 1.0 1.8 0.27 4.6 91 105
1.5 2.1 0.32 5.4 79 91
2.0 2.3 0.38 6.3 78 90
2.1 2.4 0.39 6.4 74 86
270° Arc 1.0 1.8 0.25 4.2 103 119
1.5 2.1 0.30 4.9 91 105
2.0 2.3 0.34 5.8 86 99
2.1 2.4 0.35 5.9 81 94
180° Arc 1.0 1.8 0.19 3.2 117 135
1.5 2.1 0.23 3.8 104 120
2.0 2.3 0.26 4.4 98 113
2.1 2.4 0.27 4.5 94 109
90° Arc 1.0 1.8 0.12 1.9 148 171
1.5 2.1 0.14 2.3 127 147
2.0 2.3 0.16 2.7 121 140
2.1 2.4 0.16 2.7 111 128
8 Series VAN METRIC
10° Trajectory
Q V
Nozzle Pressure Radius Flow Flow Precip Precip
bar m m3⁄h l/m mm/h mm/h
360° Arc 1.0 2.1 0.44 7.3 96 111
1.5 2.4 0.53 9.0 89 103
2.0 2.7 0.57 9.8 76 88
2.1 3.1 0.59 9.8 63 73
270° Arc 1.0 2.1 0.33 5.5 96 111
1.5 2.4 0.4 6.8 89 103
2.0 2.7 0.43 7.8 76 88
2.1 3.1 0.48 7.9 68 79
180° Arc 1.0 2.1 0.22 3.7 96 111
1.5 2.4 0.27 4.6 89 103
2.0 2.7 0.29 5.3 76 88
2.1 3.1 0.33 5.5 71 82
90° Arc 1.0 2.1 0.11 1.8 96 111
1.5 2.4 0.13 2.3 89 103
2.0 2.7 0.14 2.7 76 88
2.1 3.1 0.17 2.8 73 85
10 Series VAN METRIC
10° Trajectory
Q V
Nozzle Pressure Radius Flow Precip Precip
psi ft. gpm In/h In/h
360° Arc 15 7 1.93 3.80 4.39
20 8 2.32 3.50 4.04
25 9 2.52 3.00 3.46
30 10 2.60 2.50 2.89
270° Arc 15 7 1.45 3.80 4.39
20 8 1.75 3.50 4.04
25 9 1.89 3.00 3.46
30 10 2.10 2.70 3.12
180° Arc 15 7 0.97 3.80 4.39
20 8 1.20 3.50 4.04
25 9 1.26 3.00 3.46
30 10 1.45 2.80 3.23
90° Arc 15 7 0.48 3.80 4.39
20 8 0.58 3.50 4.04
25 9 0.63 3.00 3.46
30 10 0.75 2.90 3.35
10 Series VAN
Spray Nozzles
VAN Nozzles
Note: Turning the radius reduction screw may be required to achieve catalog radius
and flow when the arc is set at less than maximum arc
Q Square spacing based on 50% diameter of throw
V Triangular spacing based on 50% diameter of throw
Performance data taken in zero wind conditions