User manual

Info Admin Logout OK Info: Admin logout from <IP or serial console> via <Web UI or Console UI>.
Error Thermal critical Error: System Overheated!!! The system will do the auto shutdown
immediately.
Warning Thermal warning Warning: System temperature is a little bit higher.
Error Voltage critical Error: System voltages failed!!! The system will do the auto shutdown
immediately
Warning Voltage warning Warning: System voltage is a little bit higher/lower.
Info PSU restore Info: Power <number> is restored to work.
Error PSU Fail Error: Power <number> is out of work.
Info Fan restore Info: Fan <number> is restore to work.
Error Fan Fail Error: Fan <number> is out of work.
Error Fan non-exist Error: System cooling fan is not installed.
Error AC Loss Error: AC loss for the system is detected.
Info UPS Detection OK Info: UPS detection succeed
Warning UPS Detection Fail Warning: UPS detection failed
Error AC Loss Error: AC loss for the system is detected
Error UPS power low Error: UPS Power Low!!! The system will do the auto shutdown
immediately.
Info Mgmt Lan Port Active Info: Management LAN Port is active.
Warning Mgmt Lan Port Failed Warning: Fail to manage the system via the LAN Port.
Info RTC Device OK Info: RTC device is active.
Warning RTC Access Failed Warning: Fail to access RTC device
Info Reset Password Info: Reset Admin Password to default.
Info Reset IP Info: Reset network settings set to default.
• System confi g events
Level Type Description
Info Sys Confi g. Defaults Restored Info: Default system confi gurations restored.
Info Sys NVRAM OK Info: The system NVRAM is active.
Error Sys NVRAM IO Failed Error: Can’t access the system NVRAM.
Warning Sys NVRAM is full Warning: The system NVRAM is full.
• System maintenance events
Level Type Description
Info Firmware Upgraded Info: System fi rmware has been upgraded
Error Firmware Upgraded Failed Error: System fi rmware upgrade failed.
Info System reboot Info: System has been rebooted
Info System shutdown Info: System has been shutdown.
Info System Init OK Info: System has been initialized OK.
Error System Init Failed Error: System cannot be initialized in the last boot up.
B. Event notifi cations
• PD/S.M.A.R.T. events
Level Type Description
Info Disk inserted Info: Disk <slot> is inserted.
Info Disk removed Info: Disk <slot> is removed.
Warning
S.M.A.R.T. threshold exceed
condition
Warning: Disk <slot> S.M.A.R.T. threshold exceed condition occurred for
attribute of
1. read error rate
2. spin up time
3. reallocated sector count
4. seek error rate
5. spin up retries
calibration retries
Warning S.M.A.R.T. information Warning: Disk <slot>: Failure to get S.M.A.R.T information
• Physical HW events
Level Type Description
Warning ECC error Warning: Single-bit ECC error is detected.
Error ECC error Error: Multi-bit ECC error is detected.
Info ECC DIMM Installed Info: ECC Memory is installed.
Info Non-ECC installed Info: Non-ECC Memory is installed.
Error Host chip failure Error: Host channel chip failed.
Error Drive chip failure Error: Drive channel chip failed.
Warning Ethernet port failure Warning: GUI Ethernet port failed.
• HDD IO events
Level Type Description
Warning Disk error Error: Disk <slot> read block error.
Warning Disk error Error: Disk <slot> writes block error.
Warning HDD failure Error: Disk <slot> is failed.
Warning Channel error Error: Disk <slot> IO incomplete.
• SAF-TE events
Level Type Description
Info SAF-TE load conf. OK Info: SAF-TE confi guration has been loaded.
Warning SAF-TE Load Conf. Failure Error: Failed to load SAF-TE confi guration. The SAF-TE device is disabled.
Info SAF-TE is disabled Info: The SAF-TE device is disabled.
Info SAF-TE is enabled Info: The SAF-TE device is enabled
• Environmental events
Level Type Description
Info Admin Login OK Info: Admin login from <IP or serial console> via <Web UI or Console UI>.
64 Appendix Appendix 65