Specifications

DMD20/DMD50/DMD2050/DMD2050E/DMD1050/OM20 Remote Protocol Remote Operations
MN-DMDREMOTEOP Revision 9 1–47
<1> Rx Interface Type 0 = G.703 Bal T1 AMI, 1 = G.703 Bal T1 B8ZS, 2 =
G.703 B E1 HDB3, 3 = G.703 Bal T2 B6ZS, 4 = G.703
Unbal E1 HDB3, 5 = G.703 Unbal T2 B8ZS, 6 = G.703
Unbal E2 HDB3, 7 = RS422 Serial, 8 = V.35, 9 =
RS232 Serial, 10 = HSSI, 11 = ASI, 12 = Advanced
ASI, 13 = M2P Parallel, 14 = DVB Parallel, 24 =
Ethernet Bridge, 25 = MIL-188-114A, 26 = RS423
Serial, 27 = Eurocomm 256, 28= Eurocomm 512, 29 =
Eurocomm 1024, 30 = Eurocomm 2048, 31 = G.703
Unbal T3 B3ZS, 32 = G.703 Unbal E3 HDB3, 33 =
G.703 Unbal STS1 HDB3
<1> Insert Status Mask Bit 0 = Frame lock
Bit 1 = Multiframe lock. Valid in E1 PCM-30 and PCM-
30C
Bit 2 = CRC lock. Valid in T1ESF, and E1 CRC enabled
Bits 3 – 7 = Reserved
0 = Mask, 1 = Allow
<1> Rx RS N Code 2 - 255 Reed-Solomon code word length
<1> Rx RS K Code 1 - 254 Reed-Solomon message length
<1> Rx RS Depth 4, 8, or 12
<1> External Clock
Source
Reserved
<1> Data Invert 0 = None, 1 = Terrestrial, 2 = Baseband, 3 = Terrestrial
and Baseband
<1> Alarm 5 Mask Bit 0 = Trellis Decoder Lock
Bit 1 = IFEC Alarm
Bit 2 = T1/E1 Signaling
Bit 3 = TPC Conflict Check
Bit 4 – 5 = Spares
Bit 6 = DVB Frame Lock Fault
Bit 7 = Spare
0 = Mask, 1 = Allow
<1> BPSK Symbol Pairing 0 = Normal, 1 = Swapped
<1> ES Mode 0 = Normal, 1 = Enhanced
<1> ES Type 0 = RS-232, 1 = RS-485
<1> ES Baud 0 =150, 1 = 300, 2 = 600, 3 = 1200, 4 = 2400, 5= 4800,
6 = 9600, 7 = 19200, 8 = 38400, 9 = 57600, 10 =
115200
<1> ES Data Bits 0 = 7 Bits, 1 = 8 Bits
<1> IDR Overhead Type 0 = 32K Voice, 1 = 64K Data
<1> FM Orderwire Mode Reserved
<1> TMT Pattern Length Reserved
<1> EbNo Threshold Unsigned Binary Value, 0-99, Implied Decimal Point
(0.0 through 9.9 dB)
<2> Reacquisition Sweep
Limit
Binary value, 1 Hz steps, 0 - 65535
<1> Terrestrial Streaming 0 = Continuous, 1 = Burst
<1> Terrestrial Framing 0 = DVB 188, 1 = DVB 204, 2 = NONE
<1> Alarm 6 Mask Bit 0 = LBST LNB DC Current Alarm
Bit 1 = LBST LNB DC Voltage Alarm
Bit 2 = Ethernet WAN Alarm
Bits 3 – 7 = Spares
0 = Mask, 1 = Allow
<1> TPC De-Interleaver 0 = Disabled, 1 = Enabled