Specifications

DMD20/DMD50/DMD2050/DMD2050E/DMD1050/OM20 Remote Protocol Remote Operations
MN-DMDREMOTEOP Revision 9 1–31
<1> Common Alarm 2 Bit 0 = TERR FPGA Config, 1 = Fail
Bit 1 = CODEC FPGA Config, 1 = Fail
Bit 2 = CODEC Device Config, 1 = Fail
Bit 3 = TRANSEC Power Test, 1 = Fail
Bit 4 = +1.5 V Rx Alarm, 1 = Fail
Bit 5 = +1.5 V TX Alarm, 1 = Fail
Bit 6 = +3.3 V Alarm, 1 = Fail
Bit 7 = +20 V Alarm, 1 = Fail
<1> Backward Alarms Bit 0 = Backward Alarm 1 Transmitted
Bit 1 = Backward Alarm 2 Transmitted
Bit 2 = Backward Alarm 3 Transmitted
Bit 3 = Backward Alarm 4 Transmitted
Bits 4 & 5 = Spares
Bit 6 = IBS Prompt Alarm Transmitted
Bit 7 = IBS Service Alarm Transmitted
0 = No, 1 = Yes
<1> Alarm 4 Bit 0 = LBST BUC DC Current Alarm, 1 = Fail
Bit 1 = LBST BUC DC Voltage Alarm, 1 = Fail
Bit 2 = Ethernet WAN Alarm, 1 = Fail
Bit 3 = LBST BUC PLL Alarm, 1 = Fail
Bit 4 = LBST BUC Over Temperature Alarm, 1 = Fail
Bit 5 = LBST BUC Summary Alarm, 1 = Fail
Bit 6 = LBST BUC Output Enable Alarm, 1 = Fail
Bit 7 = LBST BUC Communications Alarm, 1 = Fail
Opcode: <2451h> Query a Modulator's Async Configuration
Query Response (4 Bytes)
<1> ES Mode 0 = Normal, 1 = Enhanced
<1> ES Type 0 = RS232, 1 = RS485
<1> ES Baud Rate 0 =150, 1 = 300, 2 = 600, 3 = 1200, 4 = 2400, 5= 4800,
6 = 9600, 7 = 19200, 8 = 38400, 9 = 57600, 10 =
115200
<1> ES Data Bits 0 = 7 bits, 1 = 8 bits
Opcode: <2600h> Command a Modem's Control Mode (Deprecated on DMD20, listed for
backward compatibility only)
Command Data (1 Byte)
<1> Modem control mode 0 = Front panel, 1 = Terminal, 2 = Computer
Opcode: <2601h> Command a Modulator’s Configuration
Command Data (162 Bytes)
<1> Network Spec 0 = Closed Net, 1 = IDR, 2 = IBS, 3 = D & I, 5 = DVB
SAT, 11 = MIL-188-165A, 16 = RFM, 17 = Ebem
<4> Frequency Selects the IF Frequency in Hz, IF Range = 50 MHz to
180 MHz, L-Band Range = 950 MHz to 2050 MHz
<2> Strap Code Binary value
<1> Spectral Mask 0 = INTELSAT 0.35, 18 = MIL-188-165A, 20 = DVB
0.20, 25 = DVB 0.25, 35 = DVB 0.35