Setup guide
RADVISION, an Avaya Company | Release Notes
SCOPIA XT4000 and XT5000 Series | 22
Category ID Description Resolution
Recovery Mode QC#11258
In Recovery mode only HD1 Monitor
and GLAN1 can be used
I/O Connections
QC#11259
HDMI Audio is not available on HD2
monitor
QC#11264
Black video is shown when no video
input or DVI input is available
QC#16369
In random way during Factory
default the system can display black
video for long time.
QC#16506
Blocking screensaver procedure
while it is in process can cause
camera movements
QC#13363
There is no possibility to record the
call (local and remote audio, plus
mirror of HD1 monitor) connecting a
VCR/Recorder to the HD2 Output
IOT
QC#2766
Polycom MGC50 (v 8.0.2.6): in some
cases H.239 presentation does not
function.
QC#2981
Polycom diagnostics incorrectly
identifies the SCOPIA XT Series
systems.
QC#2964
Cisco C20 cannot control the
XT5000 camera in H.323 calls.
QC#6665
Polycom MGC systems (v9.0):
SCOPIA XT5000 Series does not
receive the video stream when it is
connected to MGC with default
settings (reference Pivotal #16384-
7589).
For low bit rate calls (up to 256Kbits), set the
maximum call rate of the XT5000 to 2M (the same
max. rate as MGC) in the Administrator settings
> Call Preferences page.
For 384Kbit 2Mbit calls: go
to the MGC Advanced Properties page and
uncheck the Auto Video Bit Rate.
QC#5567
LifeSize Express LS_EX1_3.0.7 (2)
produces corrupted audio in SIP
calls with audio coding based on
G.722.1 Annex C, 48 kHz. SCOPIA
XT5000 Series cannot establish
incoming point-to-point SIP calls if
H.264 coding is used.
Update LifeSize Express to latest version. As a
temporary alternative, disable G.722.1 in Web
Administrator settings > Calls > Preferences >
Audio.
QC#16828
IOT issue with Tandberg/CISCO
MXP1500 - Reported to
Tandberg/Cisco
Disable H.264 HighProfile on XT5000.
QC#17464
In the first minutes the
Tandberg/CISCO MXP1500 will not
send video to XT5000-Reported to
Tandberg/Cisco
Disable H.264 HighProfile on XT5000.
QC#17736
IOT issue with Cisco SX20 in SIP
calls
QC#17446
Presentation issue in SIP call
between CISCO SX20 and XT5000
QC#16857
Avaya 10x0(Lifesize) v4.8 issue.
Avaya Integration Rad #57 [XT/SIP]:
SIP registered XT5000 can't do
content sharing (BFCP) with Avaya
1000-series endpoints
Upgrade 1000-series endpoints to version 4.9 or
higher
QC#11493
Incident #16384-10505: Remote
camera switch from HDX to XT5000
and reverse is not performed. Issue
reported to Polycom.
QC#18490
When more than 4 XTD clients are
connected to XT embedded MCU,
sometimes they do not receive
presentation. This happens more
frequently on slow XTD servers.
Minimal installation requirements for XTD server
are:
OS: Window Server 2003/2008
RAM: 2G
Disk: 20G
CPU: Dual Core Intel Pentium E5400 2.70GHz
NIC: 100 Mbit