SCOPIA Elite 5000 Series MCU Safety Guide Version 7.
Notice © 2000-2010 RADVISION Ltd. All intellectual property rights in this publication are owned by RADVISION Ltd and are protected by United States copyright laws, other applicable copyright laws and international treaty provisions. RADVISION Ltd retains all rights not expressly granted. This publication is RADVISION confidential. No part of this publication may be reproduced in any form whatsoever or used to make any derivative work without prior written approval by RADVISION Ltd.
Table of Contents • Symbols Used in This Manual ........................................................................ 4 • Regulatory Compliance ............................................................................... 5 • Chassis-related Safety Information ................................................................ 7 • Performing Service and Maintenance Procedures .............................................. 12 • Safety Information for SCOPIA Elite 5200 Series MCU .................
Symbols Used in This Manual CAUTION This is the user caution symbol. It indicates a condition where damage of the equipment or injury of the service personnel could occur. To reduce the risk of damage or injury, follow all steps or procedures as instructed. WARNING This is a warning symbol. It indicates potential for bodily harm and tells you how to avoid the problem. Also this is the electrical hazard symbol. It indicates that there are dangerous voltages inside the shelf.
Regulatory Compliance USA Regulatory Compliance Statements This section provides the FCC compliance statement for Class A devices and describes how to keep the system CE compliant. FCC Compliance Statement for Class A Devices This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Europe (EU) This apparatus complies with CISPR 22/EN55022 Class A and EN55024 standards when used as ITE/TTE equipment, and EN300386 for Telecommunications Network Equipment (TNE) in both installation environments, telecommunication centers and other indoor locations. JAPAN - VCCI Class A Notice WARNING This is a Class A product based on the standard of the Voluntary Control Council for Interference by Information Technology Equipment (VCCI).
Chassis-related Safety Information Unpacking CAUTION To minimize any possibility of physical damage to equipment, ensure that floor space at the installation site is neat and uncluttered. Ensure that a mechanical lift can be maneuvered in the area to lift the shelf from the shipping pallet. WARNING All poly strap-shipping bands that secure the chassis packaging are stretched tight and are under tension.
Installation This unit may be intended for stationary rack mounting. Prior to mounting the unit, verify that the rack is designed to support a unit of this kind. The SCOPIA Elite 5200 Series MCU is a 3U unit and the SCOPIA Elite 5100 Series is a 1U unit. IMPORTANT Before installing the Rack Mount Kit, ensure there will be adequate vertical space to install the chassis in addition to other equipment installed.
Power Connection Follow these basic guidelines when working with any electrical equipment: • Before beginning any procedures requiring access to the chassis interior, locate the emergency power-off switch for the room in which you are working. • Disconnect all power and external cables before moving a chassis. • Do not work alone when potentially hazardous conditions exist. • Never assume that power has been disconnected from a circuit; always check.
AC Power Connection WARNING Verify that the power cord and the outlet are compatible. Use only appropriate power cords for your power outlet configurations. WARNING Ensure that each power domain supply circuit breaker is switched OFF while completing the following power connection procedure. Failure to comply can result in personal injury. WARNING HAZARDOUS CONDITIONS—POWER SUPPLY Hazardous voltage, current, and energy levels are present inside the power supply enclosure.
WARNING Ensure that each power domain supply circuit breaker is switched OFF while completing the following power connection procedure. Failure to comply can result in personal injury. WARNING When external power is applied, the chassis is energized at all times. Power to the chassis is controlled only from the external power source, and cannot be switched off at the chassis. Failure to observe can result in personal injury.
Performing Service and Maintenance Procedures General Information Safety instructions Before handling the board, read the instructions and safety guidelines in the following pages to prevent damage to the product and to ensure your own personal safety. CAUTION Do not attempt to service the system yourself, except as explained in the SCOPIA Elite 5100/5200 Series MCU Installation Guide or Administrator Guide. Follow installation and maintenance instructions closely.
Preventing Electrostatic Discharge Static electricity can harm system boards. Perform service at an ESD workstation and follow proper ESD procedure to reduce the risk of damage to components. RADVISION strongly encourages you to follow proper ESD procedure, which can include wrist straps and smocks, when servicing equipment.
Board Hot Swap and Installation WARNING • Do not touch internal components on the blade when the unit is installed and powered. • Do not perform maintenance procedures on the blade without removing it from the chassis. • Do not remove the blades without activating the hot-swap mechanism, because it can damage the board.
Safety Information for SCOPIA Elite 5200 Series MCU Servicing Media Blade Supplied control cables are shielded. If other source is used for management cable, shielded model should be use. WARNING Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries following manufacturer’s instructions. CAUTION The Media Blade contains a lithium battery.
CAUTION Do not vacuum the air filter while it is installed in the chassis. Before you clean it, you must remove the air filter completely to prevent contaminants from being drawn into the system. Servicing Chassis Fan Tray The SCOPIA Elite 5200 Series MCU unit is equipped with a two user-serviceable fan try that. Once a month (or more often in dusty environments), examine the air filter for damage and cleanliness.
DC Power WARNING To avoid overloading wiring always connect the unit to the supply circuit. WARNING Before performing any of the following procedures, ensure that power is removed from the DC circuit. To ensure that all power is OFF, locate the circuit breaker on the panel board that services the DC circuit, switch the circuit breaker to the OFF position, and move the switch handle of the circuit breaker to the OFF position.
Product Disposal Warning WARNING Ultimate disposal of this product should be handled according to all national laws and regulations. BATTERIES Batteries in this product do not contain mercury, lead or cadmium. • The batteries used in this product comply with EU Directive 91/ 157/ EEC, EU Directive 93/ 86/ EEC, EU Directive 98/101/EEC, and EU Directive 2006/66/EC. • The product documentation includes instructional information on the proper removal and disposal of the batteries used in this product.
EU Battery Directive: The following statement either appears in the printed product user documentation or on a CD shipped with the product. Batteries Directive – Information for Users In the European Union, this label indicates that the batteries in this product should be collected separately and not be disposed of with household waste.
About RADVISION RADVISION (NASDAQ: RVSN) is the industry’s leading provider of market-proven products and technologies for unified visual communications over IP and 3G networks.
