Specifications

Board-level updates for the ATCA-45xx CPM and RTM

Updating from the LAN (Shelf Manager)

RecordtheIPaddressoftheactiveShelfManagerandtheIPMBaddressoftheCPMtobe

upgraded.Fortheexamplecommandsinthisprocedure,theIPaddressis10.100.18.20and

thetargetmoduleisinslot10(IPMBaddress0x8C).Thisinformationcanbeobtainedby

runningthefruinfotoolprovidedintheupdatebundlepackage.

1. VerifythatLANconnectivitytotheShelfManagerIPaddressisestablished:

./rsys‐ipmitool‐Ilan‐H10.100.18.20‐Anonemcinfo

Ifthecommandissuccessfulthencontinuetothenextstep.Ifthecommandfails,contact

yoursystemadministratortore‐establishtheLANinterfacefortheShelfManager.

Note:SomeshelfmanagerRMCPserversrequirelevelsofauthentication,includinga

usernameandpassword.Seethersys‐ipmitoolmanpageforotherrequiredoptions.

2. MakesurethetargetCPMexistsandiscommunicating:

./rsys‐ipmitool‐Ilan‐H10.100.18.20‐Anone‐t0x8cmcinfo

Ifthecommandfails,theCPMcannotbeupgradedinitscurrentstate.Extractandreinsert

theCPM,thenretrythecommand.Ifitstillfails,contactSupportforassistance.

3. Verifyifthefirmwarewasupdatedtothelatestversion.Thiscommandidentifiesthe

active,backup,andfileversions:

./rsys‐ipmitool‐Ilan‐H10.100.18.20‐Anone‐t0x8chpmcheckcpm7_all.hpm

4. Starttheupgradewiththiscommand:

./rsys‐ipmitool‐Ilan‐H10.100.18.20‐Anone‐t0x8chpmupgradecpm7_all.hpm

activate

Thefollowingpromptappears:

Servicesmaybeaffectedduringupgrade.Doyouwishtocontinue?y/n

Enterytocontinue.Theupgradetake sseveralminutes.Allcomponentsareupgradedon

theCPM(boot,application,andFPGA)thatdonotmatchtheversionsinthehpmfile.

WARNING:Donotinterrupttheupgradeonceyoustartit.Ifproblemsoccur,donotpoweroff

themodulebeforecontactingSupport.

Ifthecommandfails,retryitthreetimesbeforecontactingSupportforassistance.

Componentsareskippedifthetooldeterminestheyarealreadyuptodate.Thisisespecially

importantfor

thebootloader.Ifthefirmwareisresetorlosespowerwhileupdatingthe

bootloader,thefirmwareneedstobereprogrammedoverJTAG.

5. Aftertheupgradeiscomplete,upgradeandactivatetheapplicationcomponentagain.

Thiscommandupdatesthebackupcopy:

./rsys‐ipmitool‐Ilan‐H10.100.18.20‐Anone‐t0x8chpmupgradecpm7_all.hpm

component1activate

6. Enterytocontinuewhenthefollowingpromptappears:

Servicesmaybeaffectedduringupgrade.Doyouwishtocontinue?y/n

7. Enterthiscommandtoverifythatthenewfirmwareversionsarebeingused:

./rsys‐ipmitool‐Ilan‐H10.100.18.20‐Anone‐t0x8chpmcheckcpm7_all.hpm