Installation guide

EN | 5
D9124 | Operation & Installation Guide |
Bosch Security Systems | 11/03 | 39352E
Contents
Figures
Figure 1: Enclosure ........................................................... 12
Figure 2: Mounting Locations ........................................ 12
Figure 3: High Voltage on D9142 ................................. 13
Figure 4: Wire Connection to Earth Ground Stud ... 14
Figure 5: Ground Fault Detect ....................................... 14
Figure 6: D1601 Installation ........................................... 15
Figure 7: Modules Installed on the Accessory
Module Carrier ................................................. 17
Figure 8: Reset Pin ........................................................... 18
Figure 9: D1255/D1255R Command Center ........... 19
Figure 10: D1256 Command Center ............................. 19
Figure 11: D1257 Remote Fire Annunciator ................ 20
Figure 12: D192/D192G Bell Silence Switch ............23
Figure 13: D8125 Jumper Setting ...................................25
Figure 14: Connecting Field Wiring to Motherboard .26
Figure 15: Program Record Sheet ..................................27
Figure 16: Checking Resistance of Data Loops .........28
Figure 17: Connecting POPITs to Data Cable ............29
Figure 18: Connecting Devices to the Motherboard.. 29
Figure 19: Connecting Four-Wire Smoke Detectors ..30
Figure 20: Connecting Heat Detectors and Other
Mechanical Devices .......................................30
Figure 21: D166 (RJ31X Jack) Wiring ........................... 37
Figure 22: Telephone Connector and LED and
Operation Monitor LED Connections ........ 37
Figure 23: Terminals 7 and 8 Relays and
Ground Start .....................................................39
Figure 24: Phone Monitor Select ....................................39
Figure 25: D928 Dual Phone Line Switcher ................ 40
Figure 26: Service Walk Test Flowchart ........................54
Figure 27: Central Stations or Local Systems
Ampere-Hour Calculation Formula ..............59
Figure 28: Remote Station or Auxiliary Systems
Ampere-Hour Calculation Formula ..............59
Figure 29: D9142 Power Supply ..................................... 61
Figure 30: D9142 Factory Switch Settings .................. 62
Tables
Table 1: Related Documentation .................................... 7
Table 2: D9124 Operation and Installation Guide
Organization ......................................................... 8
Table 3: Specifications ...................................................... 9
Table 4: High Voltage (120 V) Connections to the
D9124 System................................................... 15
Table 5: Wiring Additional Modules ............................. 18
Table 6: D1256/D1257 Specifications.......................20
Table 7: Command Center Address Settings ............ 21
Table 8: Command Center Connections .................... 21
Table 9: D8125 Wiring .................................................... 26
Table 10: Resistance by Wire Size .................................28
Table 11: Data Loops and POPITs ..................................29
Table 12: Examples of Standby Power
Requirements (12 V Devices) ........................ 31
Table 13: Battery Discharge and Recharge Cycles... 33
Table 14: Charging Status and Low Battery LEDs ....33
Table 15: Examples of Standby Power Requirements
(24 V Devices)................................................... 34
Table 16: Self-Diagnostic Tests .......................................45
Table 17: Control Panel Programming ........................... 46
Table 18: Command Centers ........................................... 47
Table 19: Phone Line .......................................................... 47
Table 20: Communication Failure ...................................48
Table 21: Points ...................................................................49
Table 22: Data Expansion Loop Wire
Specifications .................................................... 51
Table 23: Terminal Grouping Ground Fault ..................55
Table 24: Determining Battery Requirements for
12 VDC Devices ............................................... 57
Table 25: Determining Battery Requirements for
24 VDC Devices ............................................... 58
Table 26: 24-Hour Standby ..............................................59
Table 27: 60-Hour Standby ..............................................59
Table 28: D9124 24 V Power Supply
Specifications ....................................................62