IMPORTANT Should you encounter any problems with your new product, please fever ta this instruction manual, Be sear to fife this manual in & sac [ZIT ace for future reference, [Xe l 4 rein this APR he store! WE CAN HELP YOU! online at: www.radiosys.
Satyriasis eal Tenn TEE TABLE OF CONTENTS: I. Introduction S II. Installation 6 III. Training your pet 10 IV. Maintenance il V. Troubleshooting 12 VI. Return procedure 14 VII. Accessories 14 What your Pet Containment System IS and IS NOT IS a deterrent to train pets to remain within the boundary established. IS a great training aid. 1S for residential use only. 1S for healthy dogs. If you have doubts, contact your veterinarian. IS NOT a solid barrier. It will not work without proper training.
won. Layered SLEEVE Bll 2d Frequently asked questions Q: How much area can the transmitter in my kit enclose? A: The Standard transmitter will enclose up to 25 acres, the Deluxe transmitter up to 100 acres. Q: Will the correction hurt my pet? A: The correction will get your dogs attention, but will not hand him, The static shock is similar to that of static electricity, and is designed to startle, not punish, Q: How deep do you have to bury the wire? A: 1to 3 inches.
da BEAR ROUE EHD Sin L Introduction I] How The System Works Boundary Wire The Pet Containment System consists of three primary components: i TRANSMITTER, RECEIVER, and Warning BOUNDARY WIRE (antenna). The transmitter is a very low frequency radio transmitter that plugs into a standard outlet. The signal it transmits is carried by the boundary wire which serves as an antenna } Find wire The range of the signal (i.e.
= Lee FLT HG, EH, 159s COTE FLT SISTERS HILL CT 11. Installation Lay out the sea you plan to fence on a sheet of graph paper, The transmitter will : transmit a signal from your boundary wire. Be sure to leave enough area so that your dog can move about freely within the boundaries. Basic Planning rules * The wire must make a continuous Loop back to the Transient transmitter. | Ena ee + Twisting the wires cancels the signal However, twisting 78 twists per foot three or more wires does not cancel the signal.
conger RAID LISTENS Ls Pledge DO'S and DON'TS of Installation DO read all installation instructions before starting, DON'T nin wire along electrical wires. telephone wires, television cables or antenna, or near satellite dishes DON'T run parallel to power, telephone or other scabies Cross at 90° angles.
BL BIE Cumin Ean STEVENS [5] Crossing hard surfaces Lay the wire in a convenient expansion joint or use a circular saw with a masonry SEN) : As blade to create & groove. Place the wire in p | the groove and cover with an appropriate fy) patching compound. Your local hardware store can help you choose the right Y | — compound for your type of driveway. [6] Hooking up your transmitter, Standard Transmitter 1. Connect boundary wire to boundary wire terminals. 2.
£219 12 PAID ESTES 16.215 F © FIG TL ey 8 Grounding your transmitter Proper grounding is necessary to reduce the chance of lightning damage 10 your transmitter. Connect a wire between the transmitter and a ground rod buried at least 3 fi into the ground. You may use an existing ground rod. Ground rods with clamps and 14 10 18 gauge wire may be obtained at most electrical supply stores, Locate the transmitter as close as possible to the grounding rod. Receiver Callas Assembly Attaching the supplied collar 1.
IV. Training Your Pet Training tips + Even though your dog may appear trained after one or twe days, it is important ta continue the training for the entire fourteen day period. * During the training period, your pet should only be allowed in your yard on a leash.
FIDEL ep REMS aL als Polo ie DAYS 2 THROUGH 14 Repeat steps 4 through 7 at least once per day. Days 15-30 When yarn pet shows learning progress, remove the training leash and ratio it full use of the “safe zone” After 30 days from the start of training, remove the boundary flags every other one every other day. Imaginary Gate Training 1! . L=I Remove the receiver collar and replace with a regular collar and leash. [z] Walk your pet out 10 a specific place in your yard, preferably the end of your driveway.
V. Troubleshooting System Test Using Short Loop Disconnect the boundary wire and ground wire. Then, connect a 10 foot piece of wire to the terminals and spread it out in a circle. Set the boundary size switch to B (middies) position with Standard transmitter or low with Deluxe transmitter. ey [2] Turn the Range Knob full clockwise 4 Power light on? If not, check fuses, If the fuse is good. see “Return Procedure”. 4 Loop light on? If not, see “Return Procedure”.
Wt oe mh, EIRE CORE CARDIO BEETS fa, 21% Fold Testing Correction Buy a test light (A Radio Shack™ (model # 272.1 100) or call our Service Center to purchase one) and attach to probes. Carry the receiver to the boundary wire When beep changes from high tone to low tone, the test light should light. If not, see "Rewrite Procedure” Pet Does Not Appear to Receive Correction? i Trim hair in the area of the probes to insure contact, Ww Use long probes.
VI. Return Procedure Send your product with a brief description back to the address below complete with a legible return address. No prior authorization is needed We recommend you ship your return via a carrier that offers tracking capabilities. Yor mitts pay the shipping or freight charges to ux. We will then pay the freight charges back ie yan. Your product will be repaired or replaced immediately and shipped back to you.
WARRANTY Misuse or incorrect handling is not covered If importunity cannot be repaired, Radio Systems Corporation may replace it with new or reconditioned merchandise. Randi Systems Corporation will not pay for loss of time, inconvenience, loss of use of your product, or its failure to work, or any incidental or consequential damages.
