PRO-94 Trunking Scanner Tutorials (200-0524) (PRO-94) General Scanner Tutorial Index and Table Of Contents Section 1 - Scanner Basics Section 2 - General Information and Accessories Section 3 - Racing & Conventional Scanners Section 4 - TrunkTracking Scanners PRO-94 Scanner Tutorial Conventional Programming Pro-94 Tutorial - Bank Search Pro-94 Tutorial - Direct Search Pro-94 Tutorial - Limit Search Pro-94 Tutorial - Moving a Frequency from Monitor Memory Pro-94 Tutorial - Programming Trunked Frequencies Pr
Scanner Frequently Asked Questions Index ● ● ● ● Section 1: Scanner Basics Section 2: General Information and Accessories Section 3: Racing and Conventional Scanners Section 4: TrunkTracking Scanners SECTION 1: SCANNER BASICS What is a scanner and why would I want / need one? What different types of scanners are available? What can I legally listen to? What accessories are available to improve my scanning? A broadcaster in my area now uses a digital system.
Troubleshooting My scanner hangs up on a particular frequency; however, the problem goes away when I remove the antenna. Why does my RadioShack scanner pick up the same transmission on a different frequency from the frequency I receive on a superheterodyne or dual-conversion scanner? I need a service manual, and the local store said there isn't one for my scanner.
SECTION 3 RACING SCANNERS General Questions How is a racing scanner different from a regular scanner? What racing scanners does RadioShack currently sell? What accessories are available to improve my day at the races? How do I get the most out of my scanner on race day? Do you have lists of racing frequencies? Product-specific Questions 200-0513 / PRO-74: What is the impedance of the headphone jack? 200-0513 / PRO-74: How do I use limit search? 200-0514 / PRO-89: Is there a cable for wired programming for m
200-0195 / PRO-2066: Does this have a backlight? 200-0195 / PRO-2066: What are the specifications on micro volt reception on the VHF high band (108-176 MHz)? 200-0300 / PRO-43: What is the impedance of the external speaker jack? 200-0303 / PRO-39: Is this dual or triple conversion and what are the IF frequencies? 200-0305 / PRO-46: Why won't this scanner pick up the Blue Angels frequencies? 200-0305 / PRO-46: What adapter works with this? 200-0308 / PRO-51: What charger does this require? 200-0308 / PRO-51:
200-0196 / PRO-2067: What is the attenuation for this scanner, when ATT is active? 200-0196 / PRO-2067: Why doesn't this auto-scan? 200-0310 / PRO-70: The scanner is locked and I cannot unlock it; what do I do? 200-0310 / PRO-70: Can I use NiMH batteries with this scanner and charger? 200-0310 / PRO-70: What does this use for memory backup? 200-0314 / PRO-79: Why can't I use a DC Adapter to charge batteries and why can't I use High-Capacity NiCd's? 200-0432 / PRO-2052: How do I get information on the softwa
Scanner Frequently Asked Questions Section 1 - Scanner Basics What is a scanner and why would I want / need one? What different types of scanners are available? What can I legally listen to? What accessories are available to improve my scanning? A broadcaster in my area now uses a digital system; why can't I find a digital scanner? What are birdies? Reception Notes General Troubleshooting A Guide To The Action Bands A Guide To Frequencies ❍ ❍ ❍ ❍ ❍ National Weather Frequencies Ham Radio Frequencies Citizen
Early scanners were crystal-controlled. These scanners had one or more internal slots for a crystal which allowed the radio to receive a single frequency. Crystal-controlled scanners are not currently being sold. However, a number of them turn up in pawn shops and garage sales. For example, the PRO-25 (Cat. No. 200-0106), PRO-27 (Cat. No. 200-0108), and PRO-53 (Cat. No. 200-0122) scanners were of this type.
PRO-2017 Desktop Scanner (Cat. No. 20-423) Memory Channels: 200 Computer Interface: Scanner PC Programming Kit (Cat. No. 20-048) Conversion System: Dual Conversion Size: 2 1/8" x 8 1/2" x 7" Weather Alert: Yes Frequency Range: 29-54 MHz, 108-174 MHz, 380-512 MHz User's Manual Available On-line Back to Top Back to Main Index Trunking Programmable Scanners: The newest innovation in scanners is Trunking Scanners.
PRO-93 Handheld Trunking Scanner (Cat. No. 20-523) Memory Channels: 300 Computer Interface: Can clone another PRO-93 Conversion System: Triple Conversion Weather Alert: Yes Frequency Range: 25-54, 108-174, 216-225, 406-512, 806-960 (excluding cellular) and 1240-1300 MHz User's Manual Available On-line Back to Top Back to Main Index PRO-94 Handheld Trunking Scanner (Cat. No.
PRO-2053 Desktop Trunking Scanner (Cat. No. 20-466) Memory Channels: 300 Computer Interface: Scanner PC Programming Kit (Cat. No. 20-048) Conversion System: Triple Conversion Size: 3 3/8" x 8 7/16" x 6 9/16" Weather Alert: Yes Frequency Range: 29-54, 108-174, 216-225, 406-512, 806-960 (excluding cellular) and 1240-1300 MHz User's Manual Available On-line Back to Top Back to Main Index PRO-2052 Desktop Trunking Scanner (Cat. No. 20-432) Memory Channels: 1000 Computer Interface: with Cable (Cat. No.
What can I legally listen to? You can hear police and fire departments, ambulance services, government agencies, private companies, amateur radio services, aircraft, and military operations. It is legal to listen to almost every transmission your scanner can receive. However, there are some electronic and wire communications that are illegal to intentionally intercept.
Antennas for Base Stations Outdoor Scanner/Ham Discone Antenna (Cat. No.
Indoor Scanner Antenna (Cat. No. 20-161) Product Features: ● ● ● Covers 30 to 512MHz Extends to 40" Accepts PL-259 connector (Use plug adapter 278-117 for scanners that have BNC connector) Back to Top Back to Main Index Antennas for Mobile Stations Magnet-Mount Mobile Scanner Antenna (Cat. No. 20-032) Product Features: ● ● ● Covers 25 to 1300 MHz About 36" high Includes 16 foot cable with BNC type adapter connector Note: Magnetic-mount antennas are not recommended for use on vinyl roofs.
Center-Loaded Telescoping Whip Antenna (Cat. No. 20-006) Product Features: ● ● ● Receives 25 to 1300MHz Transmits on 144 MHz, 220 MHz and 440MHz Ham bands Nine sections Back to Top Back to Main Index A broadcaster in my area now uses a digital system; why can't I find a digital scanner? Currently, most radio systems are analog systems; however, some areas have begun using digital radio systems. At this time, all of our scanners are analog only; we do not currently sell a digital scanner.
General Troubleshooting Check that you are following the correct steps per the manual. Check the frequency to be sure you are entering it correctly. Check the scanner's frequency coverage to be sure that the scanner can receive that frequency. Check the scanner's reception ability by programming a known continuous voice broadcast such as NOAA on 162.4Mhz – 162.55Mhz. You can do this by going to the Weather service band (if available on your scanner) or by programming a limit search from 160Mhz – 170Mhz.
Tel.Maint. U.S.C.G.S. Telephone Maintenance U.S. Coastal & Geodetic Survey USN U.S. Navy U.S.W.B. U.S. Weather Bureau Attention: Your scanner may not be able to receive all frequencies and/or modes of reception that are contained within this document. For complete information of your scanner's capabilities, be sure to read your owner's manual completely.
Frequency Range Allocation VHF Television 54.0 - 72.0 MHz VHF Television 76.0 - 88.0 MHz Standard FM 88.0 - 108.0 MHz VHF Television 174.0 - 216.0 MHz UHF Television 470.0 - 805.75 MHz International Broadcast Bands Several short-wave bands are allocated for international broadcasting because of the nature of propagation of high frequencies. The bands are sometimes identified according to the approximate wavelength of the signals in meters. Your scanner may receive the 11-meter band, from 25.6 26.
Primary Usage As a general rule, most of the radio activity is concentrated on the following frequencies: VHF Band (30.00 - 300.0 MHz) 144.00 - 148.00 MHz 2-Meter Amateur 153.785 - 155.980 MHz Government, Police, and Fire 158.730 - 159.460 MHz Emergency Services 160.000 - 161.900 MHz Railroad UHF Band (300.00 MHz - 3.0 GHz) 440.00 - 450.00 MHz 0.6-Meter Amateur Band FM Repeaters 450.000 - 470.000 MHz Land Mobile "Paired" Frequencies 451.025 - 454.950 MHz Base Stations 456.025 - 459.
USXX Government Classified UTIL Power & Water Utilities Frequency Bands High Frequency (HF) - (3 - 30 MHz) Very High Frequency (VHF) - (30 - 300 MHz) Ultra High Frequency (UHF) - (300 MHz - 3 GHz) High Band - (25.00 - 27.36 MHz) 25.020 - 25.320 IND 25.870 - 26.470 RTV 26.62 CAP 26.966 - 27.405 CB 27.430 - 27.630 BUS 10-Meter Amateur Band - (28.0 - 29.7 MHz) 28.000 - 29.700 HAM Low Band - (29.7 - 50 MHz - in 5 kHz steps) 29.700 - 29.790 IND 29.900 - 30.550 GOVT, MIL 30.580 - 31.
6-Meter Amateur Band (50 - 54 MHz) 50.00 - 54.00 HAM FM-TV Audio Broadcast, Wide Band (54 - 72 MHz) 59.750 TV Channel 2 65.750 TV Channel 3 71.750 TV Channel 4 Land Mobile Service Band (72 - 76 MHz) FM-TV Audio Broadcast, Wide Band (76 - 88 MHz) 81.750 TV Channel 5 87.750 TV Channel 6 FM Radio Broadcast, Wide Band (88 - 108 MHz) Aircraft Band (108 - 136 MHz) 108.000 - 121.490 AIR 121.500 AIR Emergency 121.510 - 136.000 AIR U. S. Government Band (138 - 144 MHz) 137.000 - 144.
154.600 - 154.625 BUS 154.665 - 156.240 MED, ROAD, POL, PUB 165.255 OIL 156.275 - 157.425 MARI 157.450 MED 157.470 - 157.515 TOW 157.530 - 157.725 IND, TAXI 157.740 BUS 157.770 - 158.100 TELB 158.130 - 158.460 BUS, IND, OIL, TELM, UTIL 158.490 - 158.700 TELB 158.730 - 159.465 POL, PUB, ROAD 159.480 OIL 159.495 - 161.565 TRAN 161.580 OIL 161.600 - 162.000 MARI, RTV 162.0125 - 162.35 GOVT, MIL, USXX 162.400 - 162.550 WTHR 162.5625 - 162.6375 GOVT, MIL, USXX 162.
203.750 TV Channel 11 209.750 TV Channel 12 215.750 TV Channel 13 New Mobile Narrow Band (220 - 222 MHz) 220.000 - 222.000 NEW 1.3-Meter Amateur Band (222 - 225 MHz) 222.000 - 225.000 HAM Military Aircraft Band (237.9 - 287.8 MHz) 237.900 Coast Guard Search & Rescue 239.800 FAA Weather 241.000 Army Aircraft 243.000 Military Aircraft Emergency 255.400 FAA Flight Service 257.800 Civilian Towers 287.800 Coast Guard Air/Sea Rescue Military Aircraft Band (319.1 - 383.9 MHz) 319.
462.4625 - 462.525 IND, OIL, TELM, UTIL 462.550 - 462.725 GMR 462.750 - 462.925 BUS 462.9375 - 463.1875 MED 463.200 - 467.925 BUS Family Radio Service (462.5625 - 467.7125 MHz) (Channels 1 - 14) 462.5625 FRS Channel 1 462.5875 FRS Channel 2 462.6125 FRS Channel 3 462.6375 FRS Channel 4 462.6625 FRS Channel 5 462.6875 FRS Channel 6 462.7125 FRS Channel 7 467.5625 FRS Channel 8 467.5875 FRS Channel 9 467.6125 FRS Channel 10 467.6375 FRS Channel 11 467.
577.750 TV Channel 31 583.750 TV Channel 32 589.750 TV Channel 33 595.750 TV Channel 34 601.750 TV Channel 35 607.750 TV Channel 36 613.750 TV Channel 37 619.750 TV Channel 38 625.750 TV Channel 39 631.750 TV Channel 40 637.750 TV Channel 41 643.750 TV Channel 42 649.750 TV Channel 43 655.750 TV Channel 44 661.750 TV Channel 45 667.750 TV Channel 46 673.750 TV Channel 47 679.750 TV Channel 48 685.750 TV Channel 49 691.750 TV Channel 50 697.
775.750 TV Channel 64 781.750 TV Channel 65 787.750 TV Channel 66 793.750 TV Channel 67 799.750 TV Channel 68 805.750 TV Channel 69 Note: Some cities use the 470 - 512 MHz band for land/mobile service. Conventional Systems Band - Locally Assigned 851.0125 - 855.9875 CSB Conventional/Trunked Systems Band - Locally Assigned 856.0125 - 860.9875 CTSB Trunked Systems Band - Locally Assigned 861.0125 - 865.9875 TSB Public Safety Band - Locally Assigned 866.0125 - 868.
Back to Top Back to Main Index Image Reception Radios work by simple mathematics. For example, most tune to a frequency by mixing that frequency with another (local oscillator) frequency which is slightly different. This mixing process primarily gives us the two original frequencies, their sum, and their difference. Well, the radio's Intermediate Frequency (IF) filter normally passes either the sum or difference frequency, and this is then processed into the sound we hear.
Image: A "false" signal generated by the scanner during reception and demodulation. Intermediate Frequency A frequency used in the demodulation process (see Dual-conversion and Triple-conversion). (IF): kHz (kilohertz): A unit of frequency equal to 1000 Hz. Lock-out: To mark a channel to not be scanned. MHz (megahertz): A unit of frequency equal to 1000 kHz or 1,000,000 Hz. Priority Channel: A channel which is scanned regularly during normal scanning. Reset: Return the scanner to factory settings.
Scanner Frequently Asked Questions Section 2 - General Information and Accessories GENERAL SCANNER INFORMATION Programming Do you have scanner frequency lists available? How do I enter a 7-digit frequency when the scanner only takes 6 digits? Terminology What is meant by the "step-rate" of a scanner? How do I tell if my scanner uses dual or triple conversion? What does "SMR" mean in call book lists? Troubleshooting My scanner hangs up on a particular frequency; however, the problem goes away when I remove t
200-0176 Antenna: How is it mounted and does it come with cable? 200-0188 Adapter: What replaces this adapter? 200-0282 Headphones: How much noise do these block out? 200-0282 Headphones: What is the sensitivity (dB rating)? 200-0284 Headphones: How much noise do these block out and what is it designed for? 200-0284 Headphones: What are the specifications on these headphones? GENERAL SCANNER INFORMATION Product: Programming Question: Do you have scanner frequency lists available? Answer: The only source we
Product: Terminology Question: What does "SMR" mean in call book lists? Answer: "SMR" indicates a Service Maintenance Repeater. Radio operators must be a member of that club to transmit to that repeater. Back to Index Back to Top of Section 2 Product: Troubleshooting Question: My scanner hangs up on a particular frequency; however, the problem goes away when I remove the antenna.
To the extent that service manuals exist and are in stock, schematics (service manuals) for scanners that cannot receive 800 MHz or above will continue to be available to customers and others. Modified scanners (regardless of frequency or date of manufacture) will not be serviced by RadioShack.
Product: Troubleshooting Question: My scanner stops on a particular channel or frequency when using the DC adapter and the engine is running; it works fine when the engine is not running. Answer: Something in the engine is generating RF interference. You would need to determine where this is coming from and install a filter.
Back to Index Back to Top of Section 2 Product: Usage Question: How can I record my scanner's broadcasts? Answer: You would need to connect the headphone output jack to a tape player using the 274-889 1/8" Mono Plug to Two RCA Jacks Adapter and RCA A/V Patch Cables.
Product: Usage Question: Can I use an external CB antenna with my scanner? Answer: CB antennas are optimized for the low end of the spectrum; CB frequencies are 26-28 MHz. While it may work, your reception in the higher frequencies would not be equivalent to what you would get with a scanner antenna.
Question: Is there a replacement? Answer: Yes, it is available as Cat. No. 200-0043. Back to Index Back to Top of Section 2 Product: Rubber Duckie Antenna Cat. No.
Answer: The diameter is 0.190"; the length is 31.875". Back to Index Back to Top of Section 2 Product: Discone Scanner / Ham Base Station Antenna Cat. No.: 200-0043 Question: What are the frequencies of the bottom radials? Answer: What is being referred to as "radials" are the radiating (or center) elements. In a discone antenna, the horizontal elements are connected to the shield and the cone is connected to the coax center conductor. The actual configuration is an upside down half-bow-tie.
Answer: The headphones are rated at: Impedance: 60 ohms Frequency Range: 40 Hz - 20 kHz Sensitivity: 102 1 M / 1 mW Back to Index Copyright© RadioShack Corporation 2001. All rights reserved.
Scanner Frequently Asked Questions Section 3 - Racing & Conventional Scanners RACING SCANNERS General Questions How is a racing scanner different from a regular scanner? What racing scanners does RadioShack currently sell? What accessories are available to improve my day at the races? How do I get the most out of my scanner on race day? Do you have lists of racing frequencies? Product-specific Questions 200-0513 / PRO-74: What is the impedance of the headphone jack? 200-0513 / PRO-74: How do I use limit se
200-0149 / PRO-2046: Is it digital or analog? 200-0195 / PRO-2066: I need a replacement DC adapter.
Answer: We regret we do not have on-line lists of racing frequencies. However, you can find links to on-line lists by doing a web-search for the words RACING FREQUENCIES and the specific race. We are aware of the following sites which have scanner frequencies; however, please note that these internet sites are not affiliated with RadioShack Corporation and off-site information is neither created, maintained nor verified by RadioShack Corporation.
Question: How do you program this? Answer: This is crystal-controlled, rather than programmable. While RadioShack no longer carries crystals, you may find what you need by contacting International Crystal Manufacturing Co., Inc. for assistance. International Crystal Manufacturing Co., Inc. 10 North Lee Street Oklahoma City, OK 73102 Customer Service: 606-283-5000 Technical Assistance: 800-725-1426 Please note: this company is not affiliated with RadioShack Corporation.
Answer: This scanner uses 16 switches set to either 1 or 0 to program the frequency. Here is the formula, with an example to work with: Take the display and divide it into groups of 4 bits each: 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 1 2 3 4 Group 1 is as follows: Band MHz 1 2 3 X VHF Lo 30-50 0 0 0 0 VHF Hi 150-172 0 0 1 120 UHF LO 450-470 0 1 0 420 UHF Mid 470-490 0 1 1 440.0025 UHF Hi 490-512 1 0 0 460.
Answer: The frequency ranges are as follows: VHF Mid: 30-50 MHz Aircraft: 108-136 MHz VHF High: 138-174 MHz UHF: 410-512 MHz Back to Index Back to Top of Section 3 Product: PRO-2021 Programmable Scanner Cat. No.: 200-0113 Question: How many channels and what is the frequency range? Answer: This has 200 channels.
Answer: This scanner did not come with crystals installed. While RadioShack no longer carries crystals, you may find what you need by contacting International Crystal Manufacturing Co., Inc. for assistance. International Crystal Manufacturing Co., Inc. 10 North Lee Street Oklahoma City, OK 73102 Customer Service: 606-283-5000 Technical Assistance: 800-725-1426 Please note: this company is not affiliated with RadioShack Corporation.
Question: What jack does the power cord go into? There are two jacks. Answer: For either a DC or AC power source, connect the barrel plug to the jack on the left side of the antenna - the jack on the back side of the battery pack is for charging only. Back to Index Back to Top of Section 3 Product: PRO-36 Programmable Scanner Cat. No.: 200-0137 Question: What is the recommended power adapter? Answer: This requires a 9V, 300 mA (minimum) adapter with a 2.1 mm / 5.5 mm plug.
Question: Is it triple conversion? What are the IF frequencies? Answer: No, it is dual-conversion. The IF Frequencies are 10.85 MHz and 450 kHz. Back to Index Back to Top of Section 3 Product: PRO-2046 100-Channel Programmable Mobile Scanner Cat. No.: 200-0149 Question: Is this a digital or analog scanner? Answer: This is an analog scanner. Back to Index Back to Top of Section 3 Product: PRO-2066 Trunk-Mounted Mobile Scanner Cat. No.: 200-0195 Question: I need a replacement DC adapter.
Answer: This requires a 9V, 300 mA (minimum) adapter with a 1.3 mm / 3.4 mm plug. The 273-1810 DC/DC adapter meets these requirements and includes the correct adaptaplug. The 273-1767 AC/DC adapter meets these requirements and comes with your choice of one free plug (plug "H", Cat. No. 273-1711). Back to Index Back to Top of Section 3 Product: PRO-51 200-Channel Scanner Cat. No.: 200-0308 Question: Is this a trunking scanner? Answer: No.
Back to Index Back to Top of Section 3 Product: PRO-2034 60-Channel Programmable Base Scanner Cat. No.: 200-0411 Question: Why am I not getting the last digit on the display between 29-54 MHz and 137-174 MHz? Answer: In order to enter the last digit, you need to enter frequency manually. However, you will not see the last digit -- you will see a (0) for it instead. These frequencies have a step rate of 5 kHz. Back to Index Back to Top of Section 3 Product: PRO-2036 200-Channel Scanner Cat. No.
Product: PRO-2050 VHF/UHF/Air/800 MHz 300-Channel Scanner Cat. No.: 200-0430 Question: What type of antenna does it come with? Answer: This comes with a telescoping antenna. Back to Index Back to Top of Section 3 Product: PRO-2050 VHF/UHF/Air/800 MHz 300-Channel Scanner Cat. No.: 200-0430 Question: Why do I have to turn squelch all the way for aircraft channels? Answer: Aircraft frequencies have limited access.
Product: PRO-66 Scanner Cat. No.: 200-0511 Question: What is the power adapter tip size & polarity for this scanner? Answer: 5.5 mm (Outer), 2.1 mm (Inner), Tip = Positive. This tip is available as the "M" size adaptaplug for our adapters, sold as Cat. No. 2731716. Back to Index Back to Top of Section 3 Product: PRO-67 200-Channel 800 MHz Scanner Cat. No.: 200-0512 Question: Can you charge NiMH batteries in this scanner? Answer: No.
Scanner Frequently Asked Questions Section 4 - TrunkTracking Scanners TRUNKTRACKING SCANNERS General Questions What is trunktracking and where can I get more information? How do I convert EDACS SYSTEM ID format (decimal to AFS)? I can't scan an EDACS system, and I know the frequencies are right.
200-0522 / PRO-92: What are the differences between the PRO-92 and the PRO-94 scanners? 200-0522 / PRO-92: Between the PRO-92 and PRO-94, which has the better scanning scheme? 200-0523 / PRO-93: How do I get the software & cable for this scanner? 200-0524 / PRO-94: What are the differences between the PRO-92 and the PRO-94 scanners? 200-0524 / PRO-94: Between the PRO-92 and PRO-94, which has the better scanning scheme? 200-0524 / PRO-94: How do I calculate Base Frequency? I am looking for the mathematical f
Question: I can't scan an EDACS system, and I know the frequencies are right. Answer: With an EDACS system, the frequencies have to be in a particular order. Also, unless indicated otherwise in the scanner's manual, you should not mix other frequencies in the same bank as the EDACS frequencies. We do not have information on the correct order for specific EDACS frequencies.
Product: PRO-70 50-Channel Scanner Cat. No.: 200-0310 Question: Can I use NiMH batteries with this scanner and charger? Answer: You can use NiMH batteries; however, you will need to use an external charger. The charger is for NiCD batteries only. Back to Index Back to Top of Section 4 Product: PRO-70 Scanner Cat. No.: 200-0310 Question: What does this use for memory backup? Answer: The PRO-70 does not have an internal battery.
Product: PRO-90 300-Channel TrunkTracker Scanner Cat. No.: 200-0520 Question: How should I maintain my battery pack in the best condition? Answer: To keep the battery in good condition, run the batteries completely down once a month and then recharge fully. Back to Index Back to Top of Section 4 Product: PRO-90 300-Channel TrunkTracker Scanner Cat. No.: 200-0520 Question: How long does it take to charge the battery when it is fully discharged? Answer: It takes about 14-16 hours to recharge.
Product: PRO-90 300-Channel TrunkTracker Scanner Cat. No.: 200-0520 Question: Can you store a limit search in a bank? Answer: No. Back to Index Back to Top of Section 4 Product: PRO-90 300-Channel TrunkTracker Scanner Cat. No.: 200-0520 Question: How do I reset this scanner? Answer: Turn the scanner off, hold down 2 & 9 and turn it back on. Back to Index Back to Top of Section 4 Product: PRO-90 300-Channel TrunkTracker Scanner Cat. No.
Back to Index Back to Top of Section 4 Product: PRO-92 Multi-trunking Scanner Cat. No.: 200-0522 Question: What is the difference between the 200-0522, 200-0522A and 200-0522B versions of the PRO-92? Answer: The primary differences are either in the firmware version and/or the trunked scanning method. PRO-92 200-0522 Firmware: Version 1.0 Trunked Scanning: Low Speed Handshake PRO-92 200-0522A Firmware: Version 3.
Press To Enter a Character from this Group Press To Enter a Character from this Group 1 1234567890 7 PQRS 2 ABC 7 FUNC pqrs 2 FUNC abc 8 TUV 3 DEF 8 FUNC tuv 3 FUNC def 9 WXYZ 4 GHI 9 FUNC wxyz 4 FUNC ghi 0 .-#_@+*/' 5 JKL 0 FUNC $ % ! ^ ( , ) ? -> ` 5 FUNC jkl . [SPACE] 6 MNO CL [BACKSPACE] 6 FUNC mno Back to Index Back to Top of Section 4 Product: PRO-92 Multi-trunking Scanner Cat. No.
Answer: This procedure will only work on the PRO-92, since it tracks by the SID's, and not the data channel, and only in the open mode. In closed mode, the scanner will look for programmed SID's before it stops on a transmission. Here are the steps to set this up: 1. Enter all the frequencies (both conventional and Motorola II) in the same bank with the manual programming. a.
Answer: The PC interface for the PRO-93 is not available, and it will not work with any of our currently-available interfaces. While this software is in development, we do not have a due date; however, it is currently expected to be sold under part number 940-1666. When the interface is available, it will be listed on our website. A cable and software which will work with the PRO-93 is available on-line through http://www.pro93.com/. Please note: this website is not associated with RadioShack Corporation.
Product: PRO-94 Scanner Cat. No.: 200-0524 Question: How do I turn off Hypersearch? I can't get HYPER off of the display. Answer: Hypersearch can only be turned on and off through a limit or direct search. To turn it off, you should do the following: Through Limit Search: 1. 2. 3. 4. 5. 6. 7. Press PROG, then LIMIT (SRC). Lo and 29.000 MHz appear. 29.000 MHz is the low end of the scanner's range.
PRO-94 Tutorial: Programming Conventional Frequencies This is an introduction to programming conventional (non-trunking) frequencies into your PRO-94 scanner. This tutorial will involve programming a frequency into either Bank "A" or "B", selecting which channel number to store a frequency in and storing the frequency. It will also show you how to set the delay to the "on" or "off" mode. For this tutorial, frequency 866.1625 will be stored in Bank A with delay off.
Use the number keys (0-9) to enter the channel number where you want to store a frequency. Step 4: Entering Program Mode Pro94-keypad-PROG Press PROG. The channel number you chose and PGM appear on the display. L/O (lock-out) appears at the bottom of the screen when a channel is locked out or empty (000.000). Step 5: Entering the Frequency BankA-1ch-866.1625-PGM Use the number keys (0-9) and MON/CLR (.) to enter the frequency (including the decimal point) you want to store.
BankA-1ch-866.1625-PGM Pro94-keypad-SVC(E) Press E (SVC) to the store the frequency into the channel. Step 7: Clearing a Mistake If you entered an invalid frequency in Step 5, Error appears and the scanner beeps three times. Use the number keys (0-9) to enter a valid frequency. Step 8: Storing the Delay Setting Press DELAY to pause scanning 2 seconds after the end of a transmission before scanning proceeds to the next channel. The scanner stores the setting for each channel individually.
Pro94-keypad-PROG To program the next channel in sequence, press PROG and repeat from Step 3. Step 10: Returning to Manual Mode Press the last channel number that you programmed, then press MAN to exit the programming mode. Copyright© RadioShack Corporation 2002. All rights reserved.
PRO-94 Tutorial: Service Bank Search The Service Bank Search allows you to search for weather, ham, marine, aircraft, or police (fire/emergency) transmissions without knowing the specific frequencies used in your area. The scanner is programmed with all the frequencies allocated to these services. "A Guide to the Action Bands" under Scanner Basics has detailed information on the frequencies allocated to each service band.
When the scanner stops on a transmission, quickly press HOLD (A/B) to stop searching and to listen to the transmission. HOLD will appear on the display. Step 4: Storing a Frequency Press MON/CLR (.) to store the displayed frequency from the previous step into the current monitor memory. Step 5: Searching for Additional Frequencies Press HOLD (A/B) or UP or DOWN arrow keys for at least 1 second to continue searching. Or if you didn't press MON/CLR (.
Pro94-keypad-MAN Press MAN to exit the service bank. Copyright© RadioShack Corporation 2002. All rights reserved.
PRO-94 Tutorial: Direct Search This tutorial covers running a direct search on your PRO-94. A direct search lets you search up or down from the currently displayed frequency. -dappears during searching until the scanner stops. For additional information on this product, see the links below: ● ● ● ● 20-524 PRO-94 User's Manual 20-524A PRO-94 User's Manual Scanner Basics Scanner FAQ's Step 1: Entering Direct Search Mode Pro94-keypad-MAN Press MAN. MAN appears in the display.
If you enter an invalid frequency, the scanner displays Error. Press MON/CLR (.) and return to Step 2 to re-enter the frequency or enter a new frequency. Step 4: Searching for Frequencies Press the DOWN arrow to search down or the UP arrow to search up from the selected frequency. -d-, SEARCH, and an UP or DOWN arrow appear. Go to Step 8 for information on listening to and storing frequencies.
Use the number keys (0-9) to enter the channel number, then press MAN or PROG again. Step 7: Searching for Frequencies The frequency in that channel appears on the display. Press the DOWN arrow to search down or the UP arrow to search up from the selected frequency. -d-, SEARCH, and an UP or DOWN arrow appear. Step 8: Stopping on a Frequency When the scanner stops on a transmission you want to listen to, quickly press HOLD. HOLD appears on the display.
Press MON/CLR (.) to store the display frequency into the current monitor memory. The scanner remains in HOLD mode. Step 10: Searching for Additional Frequencies Press HOLD (A/B) or either the UP or DOWN arrow keys for at least 1 second to continue searching. If you didn't press MON/CLR (.), simply press the UP or DOWN arrow keys to continue searching. Step 11: Exiting Direct Search Mode Pro94-keypad-MAN Press MAN to exit search mode. MAN appears on the display. Copyright© RadioShack Corporation 2002.
PRO-94 Tutorial: Limit Search A Limit Search lets you search with a specific range of frequencies. -L- appears during a limit search. This tutorial will show you how to set a low frequency and high frequency and then search between those frequencies. Our example shows a search between 822.7375 MHz and 867.8875 MHz.
Using the number pad, enter the frequency that is the lower limit of the range you want to search (including the decimal point). Press E (SVC). In this example, the low frequency is 822.7375. Step 4: Setting the Upper Limit Hi-1300.000-PGM Pro94-keypad-SRC(LIMIT) Press LIMIT (SRC). Hi and 1300.000 MHz (or the previous high limit frequency) appear. 1300.000 MHz is the upper limit of the scanner's range. Step 5: Entering the High Frequency Hi-867.
L-867.8375-SEARCH Press the DOWN arrow key to search from the upper to the lower limit, or the UP arrow key to search from the lower to the upper limit. -L- will appear on the display. In this example, we have pressed down to search from the upper limit to the lower limit. Step 7: Stopping on a Transmission When the scanner stops on a transmission, quickly press HOLD (A/B) to stop searching and listen to the transmission. HOLD will appear on the display.
To continue searching, press HOLD (A/B) or the UP or DOWN arrow key for at least 1 second. If you didn't press MON/CLR (.), simply press the UP or DOWN arrow key. Step 10: Exiting Limit Search Mode Pro94-keypad-MAN Press MAN. This will return you to manual mode. Copyright© RadioShack Corporation 2002. All rights reserved.
PRO-94 Tutorial: Moving a Frequency From a Monitor Memory to a Channel This tutorial shows how to move the frequencies you have stored in monitor memory to a channel. In this example, we are moving frequency 864.925 from monitor memory 3 to channel 6. For additional information on this product, see the links below: ● ● ● ● 20-524 PRO-94 User's Manual 20-524A PRO-94 User's Manual Scanner Basics Scanner FAQ's Step 1: Selecting Manual Mode Pro94-keypad-MAN Press MAN. MAN appears in the display.
Pro94-keypad-PROG Press PROG. PGM appears on the display, along with the channel number and the frequency stored in that channel. Step 4: Entering the Monitor Memory Number Press MON/CLR (.) then enter the number (0-9) of the monitor memory containing the frequency that you want to save to the channel. The frequency changes to the new frequency. For our example, you will press 3. Step 5: Storing the Frequency Pro94-keypad-SVC(E) Press E (SVC).
Repeat from Step 2 to store additional monitor memory frequencies into channels, as necessary. Step 6: Returning to Manual Mode Pro94-22b.jpg (10683 bytes) Press MAN to return to manual mode. PGM on the display changes to MAN. Copyright© RadioShack Corporation 2002. All rights reserved.
PRO-94 (20-524) Tutorial: Programming Trunked Frequencies This tutorial covers programming trunked frequencies into the PRO-94 Scanner (Cat. No. 20-524). For the tutorial on the PRO-94 Scanner (Cat. No. 20-524A), click here. The PRO-94 scanner will allow you to use the following trunk systems: Motorola Type I, Motorola Type II, and EDACS. For this tutorial, Bank A, system E1, and frequency 866.1625 are used.
Pro94-keypad-UP-DOWNnumberpad Press the number key (1-10) of the desired target storage bank. Select one of the following trunk system types by repeatedly pressing the UP or DOWN arrow keys. An E (EDACS) or M (Motorola) will also appear on the display depending on the trunk system selected.
Use the number keys (0-9) to enter a valid frequency within the trunk system. Click Here for the Police Call Frequency Lists on CD Step 6: Storing the Frequency within the Trunk System Pro94-keypad-SVC(E) Press E (SVC). Bank A and the bank number (1), the channel number, and E (EDACS) or M (Motorola) appears depending upon the trunk system selected. Notes: ● If you enter an invalid frequency (outside the selected range), the scanner beeps, the channel number flashes and ERROR appears.
BankA-TRUNK-M-2ch-000.000-PGM Press PROG or the UP arrow key to select the next channel in the bank. Repeat from Step 5 until you enter all the desired frequencies in that bank. Step 8: Activating Trunk Scan and Search Pro94-keypad-SRC(LIMIT) Press SRC to begin searching for the trunk's data channel (the channel that controls the trunk). SEARCH flashes in the lower right corner as the scanner searches for the data channel.
PRO-94 Tutorial: Using Search Skip Memory You can skip up to 50 specified frequencies during a limit or direct search and up to 20 specified frequencies during a service bank search. This lets you avoid unwanted frequencies or those already stored in a channel. For information on getting into and using these search modes, see the Limit Search Tutorial, the Direct Search Tutorial, or the Service Bank Search Tutorial. This tutorial starts with the scanner in the Marine (MRN) service bank search mode.
wx-ham-mrn-air-pol-157.400-l/o-HOLD-SEARCH To review the skipped frequencies, press HOLD to stop the search, and then press and release UP or DOWN to step through the frequencies while HOLD appears. L/O appears when you select a skipped frequency, indicating that the frequency is locked out. Step 3: Removing a Frequency from Skip To clear a single frequency from skip memory so that the scanner will stop on it during a limit, direct, or service bank search, press HOLD (A/B) to stop the search.
Press S/S (L-OUT). L/O disappears from the display screen. Step 6: Clearing All Skipped Frequencies To clear all of the skip frequencies at once while searching, press HOLD (A/B), then hold down S/S (L-OUT) until the scanner beeps twice. Copyright© RadioShack Corporation 2002. All rights reserved.
PRO-94 Tutorial: Storing Talk Group IDs in Talk Group Lists This tutorial shows you how to store a talk group ID in a talk group list. For our example, we will use the Motorola Type I as the trunk system in Bank A. For additional information on this product, see the links below: ● ● ● ● 20-524 PRO-94 User's Manual 20-524A PRO-94 User's Manual Scanner Basics Scanner FAQ's Step 1: Selecting Trunk Mode Pro94-man-keypad After the scanner begins trunk scanning, press MAN. MAN will appear on the display.
Pro94-prog-keypad Press PROG. PGM will appear on the display. Step 4: Entering ID Pro94-list-trunk-m-2-pgm-000-12 Enter the type of ID number you want to store. Notes: ● To enter a Type I ID, use the number keys to enter the block number and the fleet number, then press (.). Enter the subfleet number. ● To enter a EDACS ID, use the number keys to enter the agency number, then press (.). Next enter the fleet number and the subfleet number.
Step 6: Programming More Talk Group IDs Repeatedly press PROG or UP arrow to select the next scan list location you want to program. Then repeat Step 4 to enter another ID. Step 7: Finishing Manual Storing Pro94-svce-keypad When you finish, press E (SVC) to store the entries. Step 8: Exiting Manual Storing To exit manual storing, press TRUNK. This will automatically default to where you left manual scan before trunking. Copyright© RadioShack Corporation 2002. All rights reserved.
PRO-94 Tutorial: Setting and Testing the WX (Weather) Alert This tutorial shows you how to turn on and test the SAME (Specific Area Message Encoding) alert feature. The scanner displays this data as codes corresponding to the levels of severity (L1, L2, and L3).
When the scanner receives a SAME-coded signal, ALERT flashes and an associated "L" code appears. Press any key to turn off the alarm. The scanner displays one of the following codes to indicate the alert level: ● L1: Warning ● L2: Watch ● L3: Statement ● ----: Non-emergency Step 4: Turning Off Alert Mode Press ALT (DATA) to exit Alert mode.
To hear and test the tones for the three alert levels, press SVC (E) to select the weather service. Step 6: Initiating the Test Sequence Hold down ALT (DATA) for about 1 second. The tones sound in order L3, L2, then L1, and TEST flashes. Each alert code appears as its tone sounds. Step 7: Turning Off the Test Sequence Press any key to end the test sequence. Step 8: Returning to Manual Mode Pro94-keypad-MAN Press MAN to return to manual mode.
Copyright© RadioShack Corporation 2002. All rights reserved.
PRO-94 (20-524A) Tutorial: Programming Trunked Frequencies This tutorial covers programming trunk frequencies into the PRO-94 Scanner (Cat. No. 20-524A). For the tutorial on the PRO-94 Scanner (Cat. No. 20-524), click here. The PRO-94 scanner will allow you to use the following trunk systems: Motorola Type I, Motorola Type II, and EDACS. For this tutorial, Bank A, system E1, and frequency 866.1625 are used.
Pro94-keypad-UP-DOWNnumberpad Press the number key (1-10) of the desired target storage bank. Select one of the following trunk system types by repeatedly pressing the UP or DOWN arrow keys. E (EDACS) or M (Motorola) appear on the display depending on which trunk system you have selected.
Use the number keys (0-9) to enter a valid frequency within the trunk system. Click Here for the Police Call Frequency Lists on CD Step 6: Storing the Frequency within the Trunk System Pro94-keypad-SVC(E) Press E (SVC). Bank A and the bank number (1), the channel number, and E (EDACS) or M (Motorola) appears depending upon the trunk system selected. Notes: ● If you enter an invalid frequency (outside the selected range), the scanner beeps, the channel number flashes and ERROR appears.
BankA-TRUNK-M-2ch-000.000-PGM Press PROG or the UP arrow key to select the next channel in the bank. Repeat from Step 5 until you enter all the desired frequencies in that bank. Step 8: Activating Trunk Scan and Search Press SCAN, then SRC to begin searching for the trunk's data channel and scan conventional frequencies at the same time. Note: As the scanner looks through the frequencies, you will see them on the display. When the scanner finds the controlling data channel, the scanner begins trunking.
