Specifications

Due to the dynamic nature of the product design, the information contained in this document is subject to change without notice. Viking Electronics, and its affiliates and/or subsidiaries
assume no responsibility for errors and omissions contained in this information. Revisions of this document or new editions of it may be issued to incorporate such changes.
DOD# 178
ZF303270 Rev A
Printed in the U.S.A.
P
P
r
r
o
o
d
d
u
u
c
c
t
t
S
S
u
u
p
p
p
p
o
o
r
r
t
t
L
L
i
i
n
n
e
e
.
.
.
.
.
.
7
7
1
1
5
5
.
.
3
3
8
8
6
6
.
.
8
8
6
6
6
6
6
6
F
F
a
a
x
x
B
B
a
a
c
c
k
k
L
L
i
i
n
n
e
e
.
.
.
.
.
.
7
7
1
1
5
5
.
.
3
3
8
8
6
6
.
.
4
4
3
3
4
4
5
5
8
O
O
p
p
e
e
r
r
a
a
t
t
i
i
o
o
n
n
When the “Call” button is pressed, the E-35 phone goes off-hook, and dials a pre-programmed telephone number. The front panel LED
will light any time the phone is off hook, and flash to show dialing. In the event that the line is busy or there is a ring-no answer, the unit
can be programmed to call additional phone numbers. The phone then cycles through up to 5 pre-programmed speed dial numbers until
the call is answered. The E-35 will hang up on CPC, silence, busy signal, return to dial tone, time out or Touch Tone command (Q#). If
programmed to auto-answer, the E-35 will also answer any incoming call. The E-35 color video camera operates completely independ-
ently of the E-35 phone board. With power supplied to the camera, it will continuously output a video signal.
To Program the E-35 Phone...
...to store 123456 as the security code
...to store a Touch Tone 9, a four second pause and then a pulse
dialed 333-4444 in the first speed dial position
...to store 555-1234 in the second speed dial position
Step 2 - Enter Digits:
1 2 3 4 5 6 # 1 9
9
Q7 Q6 3 3 3 4 4 4 4 # 0 0
5 5 5 1 2 3 4 # 0 1
Step 1 -
See Section A
Enter Programming
Enter Programming
Enter Programming
I. Programming Examples
Microphone
Sensitivity
Speaker
Volume
ON
OFF
ON
OFF
1 2 3
A
B
Standard
OFF ON
EWP
A B
Standard
OFF ON
1
2
3
EWP
H. DIP Switch Programming/Speaker and Microphone Adjustments
Two POTs are provided to increase or decrease speaker volume and microphone sensitivity. In certain noisy locations
the microphone sensitivity may need to be decreased as shown below. Caution: Setting the microphone gain too high
may cause distorted audio, prevent the distant party from breaking over and inhibit second number redialing.
G. Assisted Programming
When attempting to program the E-35 phone, if the phone number of the line it is connected to is not known, the phone can be set
to automatically call Viking technical support for assistance. With DIP switch 3 set to OFF (programming mode), pushing the CALL
button will cause the E-35 phone to call Viking, whether it be connected directly to a CO line, or behind a "dial 9" PBX.
The E-35 phone will first dial 9, and then listen for second dial tone; if detected it will continue to dial Viking’s assisted programming
phone number. If a second dial tone is not detected, it then knows is not behind a PBX, so it will momentarily hang up and then
directly dial Viking’s assisted programming phone number. Since this is a long distance phone call, the line must be capable of plac-
ing long distance calls for the call to go through. When finished programming, it is very important to set DIP switch 3 back to ON
(normal operating mode), and place a test emergency call to be sure all programming was done properly.
Warning: Failure to set DIP switch 3 back to ON when finished programming will cause the E-35 phone to only call Viking Technical
Support, instead of your programmed emergency number.
DIP
Switch
1
1
2
2
3
3
Position
ON
OFF
ON
OFF
ON
OFF
Description
“CALL” button alternately connects and disconnects
calls (factory default)
“CALL” button connects calls only
Incoming calls answered (factory setting)
Incoming calls are not answered
Normal operation mode (factory setting)
Learn mode - Any incoming calls are automatically entered
into the programming mode (no security code required). Use
this option if you have forgotten your security code. Any out-
bound call will dial Viking Technical Support (see section G).
Warning: When finished programming, set this switch back to the ON
position, otherwise the E-35 phone will only call Viking Technical
Support instead of your programmed emergency number.
Switch
A
ON
OFF
Description
Normal audio detection
Increase audio detect sensitivity for low level lines. Useful
in applications in which voice or busy signals have trouble
breaking over the speaker.
Switch
B
ON
OFF