Please read before using this equipment. Owner’s Manual 2.
The FCC Wants You to Know ........................................................................................... 2 Features .................................................................................................................................. 4 Installation .............................................................................................................................. Camera Mounting Tips .........................................................................................
ˆ FCC Information FCC DECLARATION OF CONFORMITY THE FCC WANTS YOU TO KNOW This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
IMPORTANT SAFETY INSTRUCTIONS cause the product and cart combination to overturn. Read Instructions — All the safety and operating instructions should be read before the product is operated. Ventilation — Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating. Do not block or cover these openings. These openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface.
age points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product. • if the product does not operate normally by following the operating instructions Servicing — Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
RECEIVER Rotary Antenna — lets you easily adjust the antenna for the best reception. Audio/Video Out Jacks — let you see and hear activity in the monitored area through your TV or monitor, and record the action on a standard VCR. Non-Slip Rubber Feet — keep the video receiver in place on a hard, flat surface. ˆ Installation Note: Microwave ovens can cause interference. Be sure you do not position the video camera or its receiver near a microwave.
supplied mounting screws desired mounting surface. on the 2. Drill a pilot hole at each marked location. Drill a third hole, if necessary, below and between the mounting holes for the camera’s power socket cord. Thread the camera’s power socket cord through the hole, if necessary. SETTING UP THE CAMERA 1. Gently grasp the rubber cover on the front of the camera and lift it up to remove it. 2. Use a pointed object (such as a straightened paper clip) to slide the channel switch to the desired channel.
CONNECTING THE RECEIVER 3. Place the receiver in a convenient location. You can power the receiver using the supplied 12V, 400 mA AC adapter. 4. Adjust the receiver’s antenna so its flat side faces the direction where the camera is set up. Cautions: You must use a Class 2 power source that supplies regulated 12V DC and delivers at least 400 mA. Its center tip must be set to positive and its plug must fit the receiver’s DC 12V jack. The supplied adapter meets these specifications.
To a TV with a DBS Receiver or Other A/V Device tem to control any camera(s) set to the same house code. If your DBS receiver or other A/V component is connected to the TV using A/V cables, you can connect the receiver to the free LINE IN jacks on the component. If there are no LINE IN jacks, use a TV antenna splitter (available at your local RadioShack store). After you install the battery, the remote control is preset to house code A.
ˆ Operation Set the receiver’s ON/OFF switch to ON. The red indicator on the front of the receiver lights. Turn on the connected devices. If necessary, remove the camera’s focus panel cap, then adjust the lens to set the focus. Press the ON/OFF keys that have been set to the corresponding unit codes to turn the camera(s) on or off. Notes: • The cameras are preset to on when they are connected to power.
Note: The Plug ‘n Power adapter’s transceiver sends the signal to turn each camera on or off every 5 seconds. While the signal is transmitting, you cannot use other Plug ‘n Power control systems to control devices connected with the same AC line. It takes about 2 seconds for the signal to travel, so your control system should respond by the second key press. If you use the programmable timer control center (Cat.No. 612470), a device might not respond. 3.
ˆ Specifications CAMERA Imager ......................................................................................................................... CMOS Color Sensor Format .................................................................................................................................................. 1/3 in Focal Length ..................................................................................................................................... 5.6 mm Focus Distance ...........
Limited Ninety-Day Warranty This product is warranted by RadioShack against manufacturing defects in material and workmanship under normal use for ninety (90) days from the date of purchase from RadioShack companyowned stores and authorized RadioShack franchisees and dealers.
