Instructions
Table Of Contents
- 1. This manual...
- 1.1 How to use this manual
- 2. Hazard symbols
- 2.1 Levels of danger and signal words
- 2.2 Symbols and depictions used
- 3. Safety instructions
- 3.1 Intended use
- 3.2 Improper use
- 3.3 Required expert knowledge of the installer
- 3.4 Glossary - definition
- 4. Included in delivery
- 5. General view of the operating unit
- 5.1 General view of the installation housing
- 5.2 Electrical connections
- 5.3 Display and its symbols
- 5.4 Views of the standard display
- 6. Product description
- 6.1 Overview of functions
- 6.2 Functions and sample applications
- 7. Technical specifications
- 7.1 Factory settings
- 7.2 Conduct in the event of a power failure
- 8. Safety instructions for the electrical connection
- 8.1 Important information prior to the electrical connection and installation
- 8.2 Electrical connection
- 8.3 Connection diagram with a 230 V control valve
- 8.4 Connection diagram with a 24 V control valve
- 9. Installation after the electrical connection
- 10. Introduction to opening the menus and setting the functions
- 11. Initial commissioning with the help of the installation wizard
- 12. Manually changing the target temperature
- 13. Switching automatic mode on/off directly on the standard display
- 14. Calling up and displaying weather data
- 15. Menu overview
- 15.1 Menu 1 - Switching automatic mode on/off
- 15.2 Menu 2 - Setting automatic heating phases
- 15.3 Menu 3 - Setting target temperatures centrally
- 16. Menu 9 - System settings
- 16.1 Menu 9.1 - Setting the time and date
- 16.2 Menu 9.5 - Setting the week programme
- 16.3 Menu 9.7 - Installer settings
- 16.4 Menu 9.7.1 - Setting the heating mode
- 16.5 Menu 9.7.2 - Setting the sensor offset
- 16.6 Menu 9.7.3 - Setting the hysteresis / minimum on-time
- 16.7 Menu 9.7.4 - Setting the valve protection
- 16.8 Menu 9.7.5 - Setting the frost protection
- 16.9 Menu 9.7.6 - Setting the valve mode
- 16.10 Menu 9.7.7 - Performing a sensor test
- 17. Menu 9.8 - Device settings
- 17.1 Menu 9.8.1 - Switching the automatic summer/ winter time on/off
- 17.2 Menu 9.8.3 - Setting the display lighting
- 17.3 Menu 9.8.5 - Switching the button lock on/off
- 17.4 Menu 9.8.6 - Setting the holiday mode incl. the setback temperature
- 17.5 Menu 9.8.7 - Setting the party mode incl. the comfort temperature
- 17.6 Menu 9.8.0 - Displaying the software version
- 18. Menu 9.9 - DuoFern settings
- 18.1 Menu 9.9.1 - Logging DuoFern devices on/off
- 18.2 Menu 9.9.2 - Setting the DuoFern mode
- 18.3 Menu 9.9.3 - Setting the transmission channel
- 18.4 Menu 9.9.4 - Switching the weather data on/off
- 18.5 Menu 9.9.5 - Displaying the DuoFern address (radio code)
- 19. Logging on to the HomePilot®
- 20. Deleting all settings, software reset
- 21. Carrying out a hardware reset
- 22. Error messages
- 23. Dismantling
- 24. Simplified EU Declaration of Conformity
- 25. Accessories
- 26. Warranty conditions
112
EN
18.4 Menu 9.9.4 - Switching the weather
data on/off
1. Open menu 9.9.4.
2. Switch the weather data display on/
off and confirm.
OFF = Off
On = On
3. The last four digits of the DuoFern
address (radio code) of the current
environmental sensor are displayed.
Display if no environmental sensor
has been received or is in radio range
so far.
4. / Select and confirm the desired
environmental sensor.
Deleting all detected environmental sensors
Briefly press the SET button.
All environmental sensors are deleted.