Manualshelf

Specifications

ManualsBrandsRACOM ManualsComputer equipmentPROFI MR400
31323334353637383940
If the Master is located on the side of the MRxxx, the border MRxxx should be set to Slave. Depending
on the SCC interface used the MRxxx should use Multiaddressing with addresses of all the Slave units
on the RipEX network.
If the Master is located on the side of the RipEX, the border MRxxx is set like it was connected to the
Master and the Node of the connected SCC interface has to correspond to the Master's address.
5
5
9
9
8
8
7
7
6
6
1
1
2
2
3
3
4
4
RS232 RS232
3
5
5
2
2
3
Fig. 6.2: Crosslink serial cable
6.2. RipEX in Router mode
There are two basic scenarios:
• Terminal devices are connected over Ethernet
• Terminal devices are connected over COM interface
6.2.1. Terminal devices connected over Ethernet
In this scenario the border RipEX and MRxxx should be interconnected with an Ethernet cable.
Routing in both parts of the network should be set up so that communication between them is channeled
over the border modems. It is recommended that terminal devices in the two parts of the network are
located on separate LAN's.
The picture shows MORSE network settings.
S
S
Back2Back
EthIP:192.168.10.254
IP (hex):C0.A8.0A.FE
RadioIP:10.10.10.254
Routing
192.168.20.00/24via10.10.10.20
192.168.30.00/24via10.10.10.30
DefaultGW:192.168.10.253
EthIP:192.168.20.254
IP (hex):C0.A8.14.FE
RadioIP:10.10.10.20
Routing
192.168.30.00/24via10.32.10.30
Default GW:10.32.10.254
EthIP:192.168.30.254
IP (hex):C0.A8.1E.FE
RadioIP:10.10.10.30
Routing
192.168.30.00/24via10.10.10.30
Default GW:10.10.10.254
Morseaddress:69010101
EthIP:192.168.1.254
IP (hex):C0.A8.01.FE
ARP:proxyNORMAL
Mode:IP-M-IP
Art1:192.168.20.1via690101FD
192.168.30.2via690101FD
192.168.2.2via69010102
Morseaddress:690101FD
EthIP:192.168.10.253
IP (hex):C0.A8.0A.FD
GW:192.168.10.254
ARP:proxyNORMAL
Mode:IP-M-IP
Art1:192.168.1.1via69010101
192.168.2.12via69010102
Morseaddress:69010102
EthIP:192.168.2.254
IP (hex):C0.A8.02.FE
ARP:proxyNORMAL
Mode:IP-M-IP
Art1:192.168.20.2via690101FD
192.168.30.2via690101FD
192.168.1.1via69010101
EthIP:192.168.30.3
IP (hex):C0.A8.1E.03
Mask:255.255.255.0
Routing
GW:192.168.30.254
S
S
Ethcable
EthIP:192.168.20.2
IP (hex):C0.A8.14.02
Mask:255.255.255.0
Routing
GW:192.168.20.254
EthIP:192.168.1.1
Mask:255.255.255.0
Routing
IP (hex):C0.A8.01.01
GW:192.168.1.254
EthIP:192.168.30.3
IP (hex):C0.A8.02.02
Mask:255.255.255.0
Routing
GW:192.168.30.254
f1
f2
f2
f1
Fig. 6.3: RipEX - MR400 in Router mode
35© RACOM s.r.o. – RipEX Application notes
Combining MORSE and RipEX networks